EN ISO 10140-1:2016

SLOVENSKI STANDARD
01-november-2016
1DGRPHãþD
SIST EN ISO 10140-1:2010
SIST EN ISO 10140-1:2010/A1:2012
SIST EN ISO 10140-1:2010/A2:2014
$NXVWLND/DERUDWRULMVNRPHUMHQMH]YRþQHL]ROLUQRVWLJUDGEHQLKHOHPHQWRYGHO
3UDYLODXSRUDEH]DGRORþHQHL]GHONH,62
Acoustics - Laboratory measurement of sound insulation of building elements - Part 1:
Application rules for specific products (ISO 10140-1:2016)
Akustik - Messung der Schalldämmung von Bauteilen im Prüfstand - Teil 1:
Anwendungsregeln für bestimmte Produkte (ISO 10140-1:2016)
Acoustique - Mesurage en laboratoire de l'isolation acoustique des éléments de
construction - Partie 1: Règles d'application pour produits particuliers (ISO 10140-
1:2016)
Ta slovenski standard je istoveten z: EN ISO 10140-1:2016
ICS:
17.140.01 $NXVWLþQDPHUMHQMDLQ Acoustic measurements and
EODåHQMHKUXSDQDVSORãQR noise abatement in general
91.060.01 Stavbni elementi na splošno Elements of buildings in
general
91.120.20 $NXVWLNDYVWDYEDK=YRþQD Acoustics in building. Sound
L]RODFLMD insulation
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 10140-1
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2016
EUROPÄISCHE NORM
ICS 91.120.20 Supersedes EN ISO 10140-1:2010
English Version
Acoustics - Laboratory measurement of sound insulation
of building elements - Part 1: Application rules for specific
products (ISO 10140-1:2016)
Acoustique - Mesurage en laboratoire de l'isolation Akustik - Messung der Schalldämmung von Bauteilen
acoustique des éléments de construction - Partie 1: im Prüfstand - Teil 1: Anwendungsregeln für
Règles d'application pour produits particuliers (ISO bestimmte Produkte (ISO 10140-1:2016)
10140-1:2016)
This European Standard was approved by CEN on 14 August 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10140-1:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 10140-1:2016) has been prepared by Technical Committee ISO/TC 43
"Acoustics" in collaboration with Technical Committee CEN/TC 126 “Acoustic properties of building
elements and of buildings” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2017, and conflicting national standards
shall be withdrawn at the latest by February 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 10140-1:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10140-1:2016 has been approved by CEN as EN ISO 10140-1:2016 without any
modification.
INTERNATIONAL ISO
STANDARD 10140-1
Second edition
2016-08-15
Acoustics — Laboratory measurement
of sound insulation of building
elements —
Part 1:
Application rules for specific products
Acoustique — Mesurage en laboratoire de l’isolation acoustique des
éléments de construction —
Partie 1: Règles d’application pour produits particuliers
Reference number
ISO 10140-1:2016(E)
©
ISO 2016
ISO 10140-1:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 10140-1:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 General . 2
4 Structure of application rules for specific products . 2
Annex A (normative) Walls — Airborne sound insulation . 3
Annex B (normative) Doors — Airborne sound insulation . 5
Annex C (normative) Windows — Airborne sound insulation . 6
Annex D (normative) Glazing — Airborne sound insulation . 8
Annex E (normative) Small technical elements — Airborne sound insulation.15
Annex F (normative) Floors — Airborne and impact sound insulation .19
Annex G (normative) Acoustical linings — Improvement of airborne sound insulation .20
Annex H (normative) Floor coverings — Improvement of impact sound insulation .24
Annex I (normative) Shutters — Airborne sound insulation .33
Annex J (normative) Joints filled with fillers or seals — Sound reduction index .38
Annex K (normative) Roofs, roof/ceiling systems, roof windows and skylights — Rainfall sound .49
Bibliography .54
ISO 10140-1:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 43, Acoustics, Subcommittee SC 2, Building
acoustics.
This second edition cancels and replaces the first edition (ISO 10140-1:2010), which has been technically
revised.
It also incorporates the Amendments ISO 10140-1:2010/Amd 1:2012 and ISO 10140-1:2010/Amd 2:2014.
ISO 10140 consists of the following parts, under the general title Acoustics — Laboratory measurement
of sound insulation of building elements:
— Part 1: Application rules for specific products
— Part 2: Measurement of airborne sound insulation
— Part 3: Measurement of impact sound insulation
— Part 4: Measurement procedures and requirements
— Part 5: Requirements for test facilities and equipment
iv © ISO 2016 – All rights reserved

ISO 10140-1:2016(E)
Introduction
ISO 10140 (all parts) concerns laboratory measurement of the sound insulation of building elements
(see Table 1).
This part of ISO 10140 specifies the application rules for specific elements and products, including
specific requirements for preparation, mounting, operating and test conditions. ISO 10140-2 and
ISO 10140-3 contain the general procedures for airborne and impact sound insulation measurements,
respectively, and refer to ISO 10140-4 and ISO 10140-5 where appropriate. For elements and products
without a specific application rule described in this part of ISO 10140, it is possible to apply ISO 10140-2
and ISO 10140-3. ISO 10140-4 contains basic measurement techniques and processes. ISO 10140-5
contains the requirements for test facilities and equipment. For the structure of ISO 10140 (all parts),
see Table 1.
ISO 10140 (all parts) was created to improve the layout for laboratory measurements, ensure
consistency and simplify future changes and additions regarding mounting conditions of test elements
in laboratory and field measurements. It is intended for ISO 10140 (all parts) to present a well-written
and arranged format for laboratory measurements.
It is intended to update this part of ISO 10140 with application rules for other products. It is also
intended to incorporate ISO 140-18 into ISO 10140 (all parts).
Table 1 — Structure and contents of ISO 10140 (all parts)
Relevant
part of Main purpose, contents and use Detailed content
ISO 10140
ISO 10140-1 It indicates the appropriate test procedure Appropriate references to ISO 10140-2 and
for elements and products. For certain types ISO 10140-3 and product-related, specific and
of element/product, it can contain additional additional instructions on:
and more specific instructions about
— specific quantities measured;
quantities and test element size and about
preparation, mounting and operating — size of test element;
conditions. Where no specific details are
— boundary and mounting conditions;
included, the general guidelines according
ISO 10140-2 and ISO 10140-3. — conditioning, testing and operating
conditions;
— additional specifics for test report.
ISO 10140-2 It gives a complete procedure for airborne — Definitions of main quantiti
...