EN 10017:2004

SLOVENSKI STANDARD
01-december-2004
-HNOHQHSDOLFH]DYOHþHQMHLQDOLKODGQRYDOMDQMH±0HUHLQWROHUDQFH
Steel rod for drawing and/or cold rolling - Dimensions and tolerances
Walzdraht aus Stahl zum Ziehen und/oder Kaltwalzen - Maße und Grenzabmaße
Fil machine en acier destiné au tréfilage et/ou laminage a froid - Dimensions et
tolérances
Ta slovenski standard je istoveten z: EN 10017:2004
ICS:
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 10017
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2004
ICS 77.140.65 Supersedes EURONORM 17:1970
English version
Steel rod for drawing and/or cold rolling - Dimensions and
tolerances
Fil machine en acier non allié destiné au tréfilage et/ou Walzdraht aus Stahl zum Ziehen und/oder Kaltwalzen -
laminage à froid - Dimensions et tolérances Maße und Grenzabmaße
This European Standard was approved by CEN on 9 July 2004.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10017:2004: E
worldwide for CEN national Members.

Contents
Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions.4
4 Information to be supplied by the purchaser .4
4.1 Information to be supplied by the purchaser .4
4.2 Examples .4
5 Nominal sections and nominal mass.5
6 Dimensions and tolerances .6
6.1 Round rod (Fig. 1).6
6.2 Square rod (Fig. 2) .8
6.3 Rectangular rod (Fig. 3).9
6.4 Hexagonal Rod (Fig. 4).12
7 Mass of coils and checks on dimensional tolerances.14
8 Claims .14
Bibliography .15

Foreword
This document (EN 10017:2004) has been prepared by Technical Committee ECISS/TC 15 “Wire rod - Qualities,
dimensions, tolerances and specific tests”, the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by
April 2005.
This document supersedes EURONORM 17 (1970).
This document includes a Bibliography.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

1 Scope
This document specifies the dimensions, the tolerances, the nominal cross-section and the nominal mass of steel
rod for drawing.
This document concerns round, square, rectangular and hexagonal rod in steel grades specified in European
Standards.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
The requirements of this document rule when they differ from those in the standards and documents referred to
below.
EN 10021, General technical delivery requirements for steel and iron products
EN 10079:1992, Definition of steel products
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 10079:1992 apply.
4 Information to be supplied by the purchaser
4.1 Information to be supplied by the purchaser
The following information shall be supplied by the purchaser at the time of enquiry and order, to enable the supplier
to comply satisfactorily with the requirements of this document:
a) quantity to be delivered
b) product denomination (rod)
c) section (round, square, rectangular, hexagonal)
d) reference to this document
e) nominal dimensions in millimetres
f) information included in the quality product European Standard
4.2 Examples
Round rod with a diameter of 10 mm in steel C10D according EN 10016-2:
EXAMPLE 1 Round rod EN 10017 - 10 - EN 10016-2 - C10D
Rectangular rod with a width of 30 mm and thickness 5 mm in steel C3D1 according EN 10016-3:
EXAMPLE 2 Rectangular rod EN 10017 - 30 x 5 - EN 10016-3 - C3D1
Hexagonal rod with a wrench opening of 10 mm in steel C70D2 according EN 10016-4:
EXAMPLE 3 Hexagonal rod EN 10017 - 10 - EN 10016-4 - C70D2
5 Nominal sections and nominal mass
The values for sections and mass are shown in Tables 1 to 4 and are given as a guide.
3.
They have been calculated and rounded off on the basis of nominal sizes and a density of 7,85 kg/dm
For stainless steels to calculate the nominal mass, densities should be obtained from EN 10088-1.
6 Dimensions and tolerances
6.1 Round rod (Fig. 1)
Figure 1 — Round rod
Table 1 — Dimensions, tolerances, nominal section and nominal mass
Tolerance on
Tolerance on Nominal Nominal
Nominal diameter d
a
diameter section mass
ovality
(mm) (mm) (mm) (kg/m)
(mm)
5 19,63 0,154
± 0,3
5,5 23,76 0,187
± 0,3
6 28,27 0,222
± 0,3
...