EN 10025-4:2004
(Main)Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
Part 4 of this document, in addition to Part 1, specifies requirements for flat and long products of hot rolled weldable fine grain structural steels in the thermomechanical rolled condition in the grades and qualities given in Tables 2 to 4 (chemical composition) and Tables 5 to 7 (mechanical properties) in thickness £ 120 mm for flat products and in thickness £ 150 mm for long products.
In addition to EN 10025-1 the steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storage tanks, water supply tanks, etc., for service at ambient and low temperatures.
Warmgewalzte Erzeugnisse aus Baustählen - Teil 4: Technische Lieferbedingungen für thermomechanisch gewalzte schweißgeeignete Feinkornbaustähle
Teil 4 dieses Dokumentes legt zusätzlich zu Teil 1 die technischen Lieferbedingungen fest für Flach- und Langerzeugnisse aus schweißgeeigneten Feinkornbaustählen im thermomechanisch gewalzten Lieferzustand in den Sorten und Gütegruppen nach den Tabellen 2 bis 4 (chemische Zusammensetzung) und den Tabellen 5 bis 7 (mechanische Eigenschaften) in Dicken 120 mm für Flacherzeugnisse und in Dicken 150 mm für Langer-zeugnisse.
Zusätzlich zu EN 10025-1 sind die in diesem Dokument erfassten Stähle vorwiegend für die Verwendung in hochbeanspruchten geschweißten Bauteilen, z. B. Brücken, Schleusentore, Lagerbehälter, Wassertanks usw. bei Umgebungstemperatur und niedrigen Temperaturen bestimmt.
Produits laminés à chaud en aciers de construction - Partie 4: Conditions techniques de livraison pour les aciers de construction soudables à grains fins obtenus par laminage thermomécanique
Vroče valjani izdelki iz konstrukcijskih jekel – 4. del: Tehnični dobavni pogoji za termomehansko obdelana valjana variva drobnozrnata konstrukcijska jekla
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steelsProduits laminés a chaud en aciers de construction - Partie 4: Conditions techniques de livraison pour les aciers de construction soudables a grains fins obtenus par laminage thermomécaniqueWarmgewalzte Erzeugnisse aus Baustählen - Teil 4: Technische Lieferbedingungen für thermomechanisch gewalzte schweißgeeignete Feinkornbaustähle77.140.50SROL]GHONLFlat steel products and semi-products77.140.10Jekla za toplotno obdelavoHeat-treatable steelsICS:SIST EN 10025-4:2004enTa slovenski standard je istoveten z:EN 10025-4:200401-december-2004SIST EN 10025-4:2004SLOVENSKI
STANDARDSIST EN 10113-1:19971DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10025-4
November 2004 ICS 77.140.10; 77.140.50 Supersedes EN 10113-1:1993, EN 10113-3:1993 English version
Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
Produits laminés à chaud en aciers de construction -Partie 4: Conditions techniques de livraison pour les aciers de construction soudables à grains fins obtenus par laminage thermomécanique
Warmgewalzte Erzeugnisse aus Baustählen - Teil 4: Technische Lieferbedingungen für thermomechanisch gewalzte schweißgeeignete Feinkornbaustähle This European Standard was approved by CEN on 1 April 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10025-4:2004: E
List of corresponding former designations.22 Annex B (informative)
List of national standards which correspond with EURONORMS referenced.23 Bibliography.24
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.