EN 10113-1:1993
(Main)Hot-rolled products in weldable fine grain structural steels - Part 1: General delivery conditions
Hot-rolled products in weldable fine grain structural steels - Part 1: General delivery conditions
1.1 This European Standard specifies requirement for long products and flat products of hot-rolled weldable fine grain structural quality and special steels. Part 1 of this European Standard specifies the general delivery conditions Part 2 of this European Standard specifies the delivery conditions for normalized steels in the grades and qualities given in table 1 (chemical composition) and tables 3 and 4 (mechanical properties) of part 2. NOTE: Whenever normalized is mentioned, normalized rolled is also covered (see 7.2 of part 2). Part 3 of this European Standard specifies the delivery conditions for thermomechanical rolled steels in the grades and qualities given in table 1 (chemical composition) and tables 3 and 4 (mechanical properties) of part 3. The steels specified in this European Standard are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storages tanks, water supply tanks, etc., for service at ambient and low temperatures. 1.2 This European Standard does not apply to products for which other EURONORMS exist or European Standards dealing with steels for general structural applications are being prepared: - Hot-rolled products of non-alloy structural steels - (see EN 10025), - Semi-finished products for forging in general purpose structural stee~s - (see EURONORM 30). - Weathering steels for structural purposes - (see EN 10155). - Plates and wide flats made of weldable fine-grained structural steels in the quenched and tempered condition - (see prEN 10137). - Flat products in high yield strength steels for cold forming - wide flats, sheet/plate, wide and narrow strip - (see prEN 10149). - Steels for shipbuilding - normal and high strength qualities - (see EURONORM 156). - Hot finished structural hollow sections (see prEN 10210-1).
Warmgewalzte Erzeugnisse aus schweißgeeigneten Feinkornbaustählen - Teil 1: Allgemeine Lieferbedingungen
Diese europäische Norm enthält die Anforderungen an Langerzeugnisse und Flacherzeugnisse aus warmgewalzten schweissgeeigneten Feinkornbaustählen, die als Qualitäts- und Edelstähle gelten. Teil 1 dieser europäischen Norm enthält die allgemeinen Lieferbedingungen. Teil 2 dieser europäischen Norm enthält die Lieferbedingungen für normalgeglühte Stähle der in Tabelle 1 (chemische Zusammensetzung) sowie in den Tabellen 3 und 4 (mechanische Eigenschaften) des Teiles 2 genannten Sorten und Gütegruppen.
Produits laminés à chaud en aciers de construction soudables à grains fins - Partie 1: Conditions générales de livraison
La présente norme européenne spécifie les caractéristiques des produits longs et des produits plats laminés à chaud, en aciers de construction de qualité et spéciaux, à grains fins, soudables. La partie 1 de la présente norme européenne traite des conditions générales de livraison. La partie 2 de la présente norme européenne traite des conditions de livraison des aciers à l'état normalisé dans les nuances et qualités données au tableau 1 (composition chimique) et aux tableaux 3 et 4 (caractéristiques mécaniques).
Vroče valjani izdelki iz varivih drobnozrnatih konstrukcijskih jekel - 1. del: Splošni dobavni pogoji
General Information
- Status
- Withdrawn
- Publication Date
- 08-Mar-1993
- Withdrawal Date
- 09-Nov-2004
- Technical Committee
- ECISS/TC 103 - Structural steels other than reinforcements
- Drafting Committee
- ECISS/TC 10 - Structural steels - Qualities
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 10-Nov-2004
- Completion Date
- 10-Nov-2004
- Directive
- 97/23/EC - Pressure equipment
Relations
- Effective Date
- 22-Dec-2008
- Effective Date
- 22-Dec-2008
- Effective Date
- 22-Dec-2008
- Effective Date
- 22-Dec-2008
- Effective Date
- 22-Dec-2008
Get Certified
Connect with accredited certification bodies for this standard
Element Materials Technology
Materials testing and product certification.
Inštitut za kovinske materiale in tehnologije
Institute of Metals and Technology. Materials testing, metallurgical analysis, NDT.
Sponsored listings
Frequently Asked Questions
EN 10113-1:1993 is a standard published by the European Committee for Standardization (CEN). Its full title is "Hot-rolled products in weldable fine grain structural steels - Part 1: General delivery conditions". This standard covers: 1.1 This European Standard specifies requirement for long products and flat products of hot-rolled weldable fine grain structural quality and special steels. Part 1 of this European Standard specifies the general delivery conditions Part 2 of this European Standard specifies the delivery conditions for normalized steels in the grades and qualities given in table 1 (chemical composition) and tables 3 and 4 (mechanical properties) of part 2. NOTE: Whenever normalized is mentioned, normalized rolled is also covered (see 7.2 of part 2). Part 3 of this European Standard specifies the delivery conditions for thermomechanical rolled steels in the grades and qualities given in table 1 (chemical composition) and tables 3 and 4 (mechanical properties) of part 3. The steels specified in this European Standard are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storages tanks, water supply tanks, etc., for service at ambient and low temperatures. 1.2 This European Standard does not apply to products for which other EURONORMS exist or European Standards dealing with steels for general structural applications are being prepared: - Hot-rolled products of non-alloy structural steels - (see EN 10025), - Semi-finished products for forging in general purpose structural stee~s - (see EURONORM 30). - Weathering steels for structural purposes - (see EN 10155). - Plates and wide flats made of weldable fine-grained structural steels in the quenched and tempered condition - (see prEN 10137). - Flat products in high yield strength steels for cold forming - wide flats, sheet/plate, wide and narrow strip - (see prEN 10149). - Steels for shipbuilding - normal and high strength qualities - (see EURONORM 156). - Hot finished structural hollow sections (see prEN 10210-1).
1.1 This European Standard specifies requirement for long products and flat products of hot-rolled weldable fine grain structural quality and special steels. Part 1 of this European Standard specifies the general delivery conditions Part 2 of this European Standard specifies the delivery conditions for normalized steels in the grades and qualities given in table 1 (chemical composition) and tables 3 and 4 (mechanical properties) of part 2. NOTE: Whenever normalized is mentioned, normalized rolled is also covered (see 7.2 of part 2). Part 3 of this European Standard specifies the delivery conditions for thermomechanical rolled steels in the grades and qualities given in table 1 (chemical composition) and tables 3 and 4 (mechanical properties) of part 3. The steels specified in this European Standard are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storages tanks, water supply tanks, etc., for service at ambient and low temperatures. 1.2 This European Standard does not apply to products for which other EURONORMS exist or European Standards dealing with steels for general structural applications are being prepared: - Hot-rolled products of non-alloy structural steels - (see EN 10025), - Semi-finished products for forging in general purpose structural stee~s - (see EURONORM 30). - Weathering steels for structural purposes - (see EN 10155). - Plates and wide flats made of weldable fine-grained structural steels in the quenched and tempered condition - (see prEN 10137). - Flat products in high yield strength steels for cold forming - wide flats, sheet/plate, wide and narrow strip - (see prEN 10149). - Steels for shipbuilding - normal and high strength qualities - (see EURONORM 156). - Hot finished structural hollow sections (see prEN 10210-1).
EN 10113-1:1993 is classified under the following ICS (International Classification for Standards) categories: 77.140.10 - Heat-treatable steels. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 10113-1:1993 has the following relationships with other standards: It is inter standard links to EN 10025-4:2004, EN 10025-1:2004, EN 10025-3:2004; is excused to EN 10113-2:1993, EN 10113-3:1993. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 10113-1:1993 is associated with the following European legislation: EU Directives/Regulations: 97/23/EC; Standardization Mandates: M/071, M/BC/CEN/86/1. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 10113-1:1993 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Warmgewalzte Erzeugnisse aus schweißgeeigneten Feinkornbaustählen - Teil 1: Allgemeine LieferbedingungenProduits laminés a chaud en aciers de construction soudables a grains fins - Partie 1: Conditions générales de livraisonHot-rolled products in weldable fine grain structural steels - Part 1: General delivery conditions77.140.10Jekla za toplotno obdelavoHeat-treatable steelsICS:Ta slovenski standard je istoveten z:EN 10113-1:1993SIST EN 10113-1:1997en01-maj-1997SIST EN 10113-1:1997SLOVENSKI
STANDARD
S
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...