EN ISO 12543-1:2021

SLOVENSKI STANDARD
01-julij-2022
Nadomešča:
SIST EN ISO 12543-1:2012
Steklo v gradbeništvu - Lepljeno steklo in lepljeno varnostno steklo - 1. del: Slovar
in opis sestavnih delov (ISO 12543-1:2022)
Glass in building - Laminated glass and laminated safety glass - Part 1: Vocabulary and
description of component parts (ISO 12543-1:2021)
Glas im Bauwesen - Verbundglas und Verbund-Sicherheitsglas - Teil 1: Definitionen und
Beschreibung von Bestandteilen (ISO 12543-1:2022)
Verre dans la construction - Verre feuilleté et verre feuilleté de sécurité - Partie 1:
Vocabulaire et description des composants (ISO 12543-1:2021)
Ta slovenski standard je istoveten z: EN ISO 12543-1:2021
ICS:
01.040.81 Steklarska in keramična Glass and ceramics
industrija (Slovarji) industries (Vocabularies)
81.040.20 Steklo v gradbeništvu Glass in building
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 12543-1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2021
EUROPÄISCHE NORM
ICS 01.040.81; 81.040.20 Supersedes EN ISO 12543-1:2011
English Version
Glass in building - Laminated glass and laminated safety
glass - Part 1: Vocabulary and description of component
parts (ISO 12543-1:2021)
Verre dans la construction - Verre feuilleté et verre Glas im Bauwesen - Verbundglas und Verbund-
feuilleté de sécurité - Partie 1: Vocabulaire et Sicherheitsglas - Teil 1: Definitionen und Beschreibung
description des composants (ISO 12543-1:2021) von Bestandteilen (ISO 12543-1:2021)
This European Standard was approved by CEN on 25 October 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12543-1:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 12543-1:2021) has been prepared by Technical Committee ISO/TC 160 "Glass
in building" in collaboration with Technical Committee CEN/TC 129 “Glass in building” the secretariat
of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2022, and conflicting national standards shall be
withdrawn at the latest by June 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12543-1:2011.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 12543-1:2021 has been approved by CEN as EN ISO 12543-1:2021 without any
modification.
INTERNATIONAL ISO
STANDARD 12543-1
Third edition
2021-12
Glass in building — Laminated glass
and laminated safety glass —
Part 1:
Vocabulary and description of
component parts
Verre dans la construction — Verre feuilleté et verre feuilleté de
sécurité —
Partie 1: Vocabulaire et description des composants
Reference number
ISO 12543-1:2021(E)
ISO 12543-1:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 12543-1:2021(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 General . 1
3.2 Laminated glass and laminated safety glass . 2
4 Description of component parts . .4
4.1 General . 4
4.2 Glass composition and type . 4
4.2.1 General . 4
4.2.2 Glass composition . 4
4.2.3 Glass type . 4
4.2.4 Other characteristics of glass . 5
4.3 Plastic glazing sheet material . 5
4.4 Interlayers . 5
4.5 Films, plates, wires and grids . 5
Bibliography . 6
iii
ISO 12543-1:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 160, Glass in building, Subcommittee
SC 1, Product considerations, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 129, Glass in building, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 12543-1:2011), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— editorial changes have been made;
— definitions in Clause 3 has been modified.
A list of all parts in the ISO 12543 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
INTERNATIONAL STANDARD ISO 12543-1:2021(E)
Glass in building — Laminated glass and laminated safety
glass —
Part 1:
Vocabulary and description of component parts
1 Scope
This document defines terms and describes component parts for laminated glass and laminated safety
glass for use in building.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 12543-2, Glass in building — Laminated glass and laminated safety glass — Part 2: Laminated safety
glass
ISO 12543-3, Glass in building — Laminated glass and laminated safety glass — Part 3: Laminated glass
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1 General
3.1.1
laminated glass
assembly consisting of one sheet of glass with one or more sheets of glass and/or plastic glazing sheet
material joined together with one or more interlayers (3.2.7)
Note 1 to entry: See ISO 12543-3.
3.1.2
laminated safety glass
laminated glass (3.1.1) classified in accordance with a soft body impact standard where in the case of
breakage the interlayer (3.2.7) serves to retain the glass fragments, limits the size of opening, offers
residual resistance and reduces the risk o
...