EN 1680:2025
(Main)Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms
Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms
This document specifies a test method for PE valves to maintain tightness during and after being subjected to a force, applied as a bending moment to the operating mechanism.
Valves according to these standards are intended for use in polyethylene (PE) piping systems for the transport of fluids.
When specified in the product standard, this document can be applied to valves of material other than PE.
Kunststoff-Rohrleitungssysteme - Armaturen für Rohrleitungssysteme aus Polyethylen (PE) - Prüfverfahren für die Dichtheit während und nach der Aufbringung eines Biegemoments auf das Betätigungsorgan
Dieses Dokument legt ein Prüfverfahren für Armaturen aus PE zur Aufrechterhaltung der Dichtheit während und nach Einwirkung einer Kraft fest, die als Biegemoment auf das Betätigungsorgan aufgebracht wird.
Armaturen nach diesen Normen sind für den Einsatz in Rohrleitungssystemen aus Polyethylen (PE) für den Transport von Flüssigkeiten vorgesehen.
Wenn in der Produktnorm festgelegt, kann dieses Dokument auf Armaturen aus einem anderen Werkstoff als PE angewendet werden.
Systèmes de canalisations en plastique - Robinets pour les systèmes de canalisations en polyéthylène (PE) - Méthode d'essai d'étanchéité sous et après une flexion appliquée au mécanisme d'entraînement
Le présent document spécifie une méthode d’essai pour les robinets en PE devant maintenir l’étanchéité pendant et après avoir été soumis à une force, appliquée comme un moment de flexion au mécanisme d’entrainement.
Les robinets conformes à ces normes sont destinés à être utilisés dans des systèmes de canalisations en polyéthylène (PE) pour le transport de fluides.
Lorsque cela est spécifié dans la norme produit, le présent document peut être appliqué à des robinets en matériau autre que le PE.
Cevni sistemi iz polimernih materialov - Ventili za cevne sisteme iz polietilena (PE) - Metoda za preskus neprepustnosti med upogibanjem zaradi uporabe zapiralnih mehanizmov in po njem
Ta dokument določa preskusno metodo za ventile iz polietilena (PE), s katero se vzdržuje njihova neprepustnost med upogibanjem zaradi uporabe zapiralnega mehanizma in po njem. Ventili v skladu s temi standardi so namenjeni za uporabo v cevnih sistemih iz polietilena za transport tekočin. Če je tako določeno v standardu za izdelek, je mogoče ta dokument uporabiti tudi za ventile iz drugih materialov.
General Information
- Status
- Published
- Publication Date
- 04-Mar-2025
- Technical Committee
- CEN/TC 155 - Plastics piping systems and ducting systems
- Drafting Committee
- CEN/TC 155/WG 32 - Valves
- Current Stage
- 6060 - Definitive text made available (DAV) - Publishing
- Start Date
- 05-Mar-2025
- Due Date
- 27-Feb-2025
- Completion Date
- 05-Mar-2025
Relations
- Effective Date
- 22-Jan-2023
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
Frequently Asked Questions
EN 1680:2025 is a standard published by the European Committee for Standardization (CEN). Its full title is "Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms". This standard covers: This document specifies a test method for PE valves to maintain tightness during and after being subjected to a force, applied as a bending moment to the operating mechanism. Valves according to these standards are intended for use in polyethylene (PE) piping systems for the transport of fluids. When specified in the product standard, this document can be applied to valves of material other than PE.
This document specifies a test method for PE valves to maintain tightness during and after being subjected to a force, applied as a bending moment to the operating mechanism. Valves according to these standards are intended for use in polyethylene (PE) piping systems for the transport of fluids. When specified in the product standard, this document can be applied to valves of material other than PE.
EN 1680:2025 is classified under the following ICS (International Classification for Standards) categories: 23.060.01 - Valves in general. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 1680:2025 has the following relationships with other standards: It is inter standard links to EN 1680:1997, EN 837-1:1996, EN 1555-2:2025, EN 12201-2:2024, EN 12201-4:2024, EN 1555-4:2021, EN 1555-4:2025, EN ISO 16486-4:2022, EN ISO 16486-4:2025, EN 1555-4:2011, EN 12201-4:2012. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 1680:2025 is associated with the following European legislation: EU Directives/Regulations: 305/2011. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 1680:2025 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...