EN 1680:1997
(Main)Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms
Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms
This draft standard specifies a method for testing the ability of a valve, intended for use in PE piping systems for gas supply, to maintain its pressure retaining capabilities under and after being subject to a bending moment appliedto the operating mechanism (cap).
Kunststoff-Rohrleitungssysteme - Armaturen für Systeme aus Polyethylen (PE) - Prüfverfahren für die Dichtheit während und nach der Aufbringung eines Biegemomentes auf den Betätigungsmechanismus
Dieser Normentwurf legt ein Verfahren zur Bestimmung der Fähigkeit einer Armatur für den Einsatz in PE-Rohrleitungssystemen für Gas fest, ihr Vermögenzur Aufrechterhaltung des Drucks während und nach Aufbringung eines Biegemoments auf den Betätigungsmechanismus (Kappe) zu behalten.
Systèmes de canalisations en plastique - Robinets pour les systèmes de canalisations en polyéthylène (PE) - Méthode d'essai d'étanchéité sous et après une flexion appliquée au mécanisme d'entraînement
Cette norme spécifie une méthode pour vérifier la capacité d'un robinet, prévu pour être utilisé dans les systèmes de canalisation en PE pour la distribution de gaz, de maintenir ses possibilités de retenue de la pression sous flexion et après être soumis à un moment de flexion appliqué au mécanisme d'entraînement (carré).
Cevni sistemi iz polimernih materialov - Ventili za cevne sisteme iz polietilena (PE) - Metoda za preskus neprepustnosti med upogibanjem zaradi uporabe zapiralnih mehanizmov in po njem
General Information
- Status
- Withdrawn
- Publication Date
- 21-Jan-1997
- Withdrawal Date
- 20-Jan-2026
- Technical Committee
- CEN/TC 155 - Plastics piping systems and ducting systems
- Drafting Committee
- CEN/TC 155/WG 32 - Valves
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 05-Mar-2025
- Completion Date
- 21-Jan-2026
- Directive
- 89/106/EEC - Construction products
Relations
- Effective Date
- 22-Jan-2023
Frequently Asked Questions
EN 1680:1997 is a standard published by the European Committee for Standardization (CEN). Its full title is "Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms". This standard covers: This draft standard specifies a method for testing the ability of a valve, intended for use in PE piping systems for gas supply, to maintain its pressure retaining capabilities under and after being subject to a bending moment appliedto the operating mechanism (cap).
This draft standard specifies a method for testing the ability of a valve, intended for use in PE piping systems for gas supply, to maintain its pressure retaining capabilities under and after being subject to a bending moment appliedto the operating mechanism (cap).
EN 1680:1997 is classified under the following ICS (International Classification for Standards) categories: 23.060.01 - Valves in general. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 1680:1997 has the following relationships with other standards: It is inter standard links to EN 1680:2025. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 1680:1997 is associated with the following European legislation: EU Directives/Regulations: 305/2011, 89/106/EEC. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 1680:1997 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov - Ventili za cevne sisteme iz polietilena (PE) - Metoda za preskus neprepustnosti med upogibanjem zaradi uporabe zapiralnih mehanizmov in po njemKunststoff-Rohrleitungssysteme - Armaturen für Systeme aus Polyethylen (PE) - Prüfverfahren für die Dichtheit während und nach der Aufbringung eines Biegemomentes auf den BetätigungsmechanismusSystemes de canalisations en plastique - Robinets pour les systemes de canalisations en polyéthylene (PE) - Méthode d'essai d'ét
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...