iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 837-1:1996

(Main)

Pressure gauges - Part 1: Bourdon tube pressure gauges - Dimensions, metrology, requirements and testing

Pressure gauges - Part 1: Bourdon tube pressure gauges - Dimensions, metrology, requirements and testing

This European standard specifies requirements for Bourdon tube (designated by B, see clause 12) indicating pressure gauges, vacuum gauges and combined vacuum and pressure gauges (compound gauges), with circular, spiral or coiled forms, from 40 to 250 nominal size with ranges up to 1600 bar for the measurement of gauge pressure. A reading of zero bar is atmospheric pressure.

Druckmessgeräte - Teil 1: Druckmessgeräte mit Rohrfedern -Masse, Messtecknik, Anforderungen und Prüfung

Diese Europäische Norm legt die Anforderungen für anzeigende Druckmeßgeräte  mit Rohrfedern (Kurzzeichen B, siehe Abschnitt 12) in Kreis-, Spiral- oder Schraubenform zum Messen von positiven und/oder negativen Überdrücken fest. S Sie gilt für Nenngrößen von 40 bis 250 und für Anzeigebereiche bis 1600 bar. Der atmosphärische Luftdruck entspricht der Anzeige 0 bar. 1 bar = 10 5 Pa. Die hier behandelten Druckmeßgeräte haben ein rundes Zifferblatt mit konzentrischer Skale und sind für industrielle Anwendungen und als Prüfmeßgeräte vorgesehen.

Manomètres - Partie 1: Manomètres à tubes de Bourdon - Dimensions, métrologie, prescriptions et essais

La présente norme européenne définit les prescriptions des manomètres, vacuomètres et manovacuomètres à tube de Bourdon (désigné par B, voir article 12), de forme circulaire, spirale ou hélicoïde, de dimensions nominales comprises entre 40 et 250, utilisée pour la mesure des pressions relatives sur une plage allant jusqu'à 1600 bar. La pression atmosphérique correspond à une lecture égale à zéro.

Merilniki tlaka - 1. del: Merilniki tlaka z Bourdonovo cevjo - Mere, meroslovje, zahteve in preskušanje

General Information

Status
Published
Publication Date
10-Dec-1996
ICS
17.100 - Measurement of force, weight and pressure
Technical Committee
CEN/TC 141 - Pressure gauges - Thermometers - Means of measuring and/or recording temperature in the cold chain
Drafting Committee
CEN/TC 141/WG 6 - Tube Bourdon pressure gauges
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
08-Jun-2022
Ref Project
SIST EN 837-1:1997 - Pressure gauges - Part 1: Bourdon tube pressure gauges - Dimensions, metrology, requirements and testing

Relations

Corrected By
EN 837-1:1996/AC:1998 - Pressure gauges - Part 1: Bourdon tube pressure gauges - Dimensions, metrology, requirements and testing
Effective Date
22-Dec-2008

Buy Standard

EN 837-1:1997EN 837-1:1997
PreviousNext
Standard
EN 837-1:1997
English language
39 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Merilniki tlaka - 1. del: Merilniki tlaka z Bourdonovo cevjo - Mere, meroslovje, zahteve in preskušanjeDruckmessgeräte - Teil 1: Druckmessgeräte mit Rohrfedern -Masse, Messtecknik, Anforderungen und PrüfungManometres - Partie 1: Manometres a tubes de Bourdon - Dimensions, métrologie, prescriptions et essaisPressure gauges - Part 1: Bourdon tube pressure gauges - Dimensions, metrology, requirements and testing17.100Merjenje sile, teže in tlakaMeasurement of force, weight and pressureICS:Ta slovenski standard je istoveten z:EN 837-1:1996SIST EN 837-1:1997en01-april-1997SIST EN 837-1:1997SLOVENSKI
STANDARD
SIST EN 837
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 837-1:1996/AC:1998(Corrigendum)
Pressure gauges - Part 1: Bourdon tube pressure gauges - Dimensions, metrology, requirements and testing
SIST EN 837-1:1997/AC:2001

TC - Mistake

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 837-2:1997(Main)
Pressure gauges - Part 2: Selection and installation recommendations for pressure gauges
SIST EN 837-2:1998

This part of prEN 837               only applies to those pressure gauges whose pressure responsive element measuring system is a metal part which deforms under the effect of the pressure measured, as defined in prEN 837-1 and   EN 837-3. This standard has been prepared to assist in the selection, installation and use of pressure gauges to ensure that they give satisfactory service for the intended application with the maximum level of safety.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 837-3:1996(Main)
Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing
SIST EN 837-3:1997

This European Standard specifies requirements for diaphragm and capsule (designated by D and C respectively, see clause 12) indicating pressure gauges, vacuum gauges and combined vacuum and pressure gauges (compound gauges), from 50 to 250 nominal size with ranges up to 25 bar for the measurement of gauge pressure. A reading of zero bar is atmospheric pressure.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 472:1994(Main)
Pressure gauges - Vocabulary
SIST EN 472:1996

This European Standard defines the fundamental and general terms to be used for pressure gauges.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16661:2015(Main)
Road vehicles and Tyre Pressure Gauges (TPG) - Interoperability between Tyre Information Systems (TIS) and TPG - Interfaces and Requirements
SIST EN 16661:2015

This European Standard applies to the tyre pressure gauges (TPG) which operate using pressure equipment (devices used in fixed or mobile installations) to inflate the tyres of road using vehicles (M1 and M2 categories) and which may be capable of interacting with vehicles equipped with tyre pressure monitoring systems (TPMS) whereby the TPG may be steered by the TPMS/vehicle.
To set the correct tyre inflation, this European Standard defines requirements and processes for the interoperability of TPG with TPMS/vehicle, through standardized interfaces and data exchange formats allowing advanced information, management and control systems between TPG and TPMS/vehicle. The architecture is open and scalable to support the different levels of interoperability (from full interoperability to fully manual).
This European Standard does not define communication protocols (works specifically made under M/453 European mandate).
This European Standard may be applied to all TPG categories referenced in the revision of EN 12645.
The driver/operator is considered as being responsible for the validation of the parameters and tyre pressure.
This European Standard will be applicable upon development of Infrastructure solution (V2I-I2V communication solutions).

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 45501:2015(Main)
Metrological aspects of non-automatic weighing instruments
SIST EN 45501:2015

This European Standard has been adapted from the OIML Recommendation R 76-1, Edition 2006, Non-automatic weighing instruments Part 1 - Metrological and technical requirements – Tests by a Joint Working Group from CEN and CENELEC. It was elaborated following a standardization request from the Commission of the European Communities to CEN and CENELEC to establish a European Standards related to Council Directive 2009/23/EC on Non-automatic weighing instruments.

  • Standard
    142 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12645:2014(Main)
Tyre pressure measuring instruments - Devices for inspection of pressure and/or inflation / deflation of tyres for motor vehicles - Metrology, requirements and testing
SIST EN 12645:2014

This European Standard defines metrological and technical requirements and tests of tyre pressure measuring instruments.
Tyre pressure measuring instruments (often referred to as Tyre Pressure Gauges, [TPG]) are for the inspection of pressure and/or inspection of inflation/deflation of tyres of motor vehicles.
It establishes in the context of motor vehicles tyres, the minimum characteristics of the chain of measurement of tyre pressure measuring instruments intended to increase, inspect or adjust the pressure of tyres inflated by air or nitrogen.
These devices, classified in different categories, are hereinafter referred to by generic term, "tyre pressure measuring instruments".
This chain of measurement consists of all the elements between the tyre valve and the display device (connector, hose, control device, measurement components, reservoir, preset device etc.).
They indicate the pressure difference (pe) between the air or the nitrogen in the tyre and the atmosphere.
The field of application established above can be extended to other applications where no specific standard exists.
Because of the influence of tyre pressure on road safety and energy efficiency, periodical reverification is strongly advised.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 837-1:1996/AC:1998(Corrigendum)
Pressure gauges - Part 1: Bourdon tube pressure gauges - Dimensions, metrology, requirements and testing
SIST EN 837-1:1997/AC:2001

TC - Mistake

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 837-2:1997(Main)
Pressure gauges - Part 2: Selection and installation recommendations for pressure gauges
SIST EN 837-2:1998

This part of prEN 837               only applies to those pressure gauges whose pressure responsive element measuring system is a metal part which deforms under the effect of the pressure measured, as defined in prEN 837-1 and   EN 837-3. This standard has been prepared to assist in the selection, installation and use of pressure gauges to ensure that they give satisfactory service for the intended application with the maximum level of safety.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 837-3:1996(Main)
Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing
SIST EN 837-3:1997

This European Standard specifies requirements for diaphragm and capsule (designated by D and C respectively, see clause 12) indicating pressure gauges, vacuum gauges and combined vacuum and pressure gauges (compound gauges), from 50 to 250 nominal size with ranges up to 25 bar for the measurement of gauge pressure. A reading of zero bar is atmospheric pressure.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day