Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2013)

ISO 14113:2013 specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied, and dissolved gases up to a maximum working pressure of 450 bar (45 MPa), within the ambient temperature range of −20 °C to +60 °C.
It applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage. It does not cover rubber or thermoplastic hoses for welding, cutting, and allied processes (see ISO 3821 and ISO 12170). It does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG).

Gasschweißgeräte - Gummi- und Kunststoffschläuche und Schlauchleitungen für Industriegase bis zu einem Druck von 450 bar (45 MPa) (ISO 14113:2013)

In dieser Norm sind Anforderungen für Gummi- und Kunststoffschläuche und Schlauchleitungen für Druck- oder Flüssiggase bis zu einem maximalen Betriebsdruck von 450 bar (45 MPa) im Bereich der Umgebungstemperatur zwischen –20 °C bis +60 °C festgelegt.
Diese Norm ist anwendbar für Hochdruckschlauchleitungen, welche verwendet werden, um industrielle Gas-flaschen oder Bündel ohne Hauptstellendruckregler zu Batterien zusammenzuschließen.
Diese Norm gilt nicht für Gummi- oder thermoplastische Schläuche für Schweißen, Schneiden und verwandte Prozesse (siehe ISO 3821 und ISO 12170).
Diese Norm gilt nicht für tiefkalte verflüssigte Gase oder LPG (en: liquified petroleum gases) (Flüssiggas).

Matériel de soudage aux gaz - Tuyaux souples et flexibles en caoutchouc et en plastique pour des gaz industriels jusqu'à 450 bar (45 MPa) (ISO 14113:2013)

L'ISO 14113:2013 spécifie les exigences relatives aux tuyaux souples et fiexibles en caoutchouc et en plastique devant être utilisés avec des gaz comprimés, liquéfiés ou dissous jusqu'à une pression maximale de service de 450 bar (45 MPa) à des températures ambiantes comprises entre −20 °C et +60 °C.
Elle s'applique aux flexibles utilisés pour relier les bouteilles de gaz industriels aux collecteurs et aux cadres de bouteilles avant toute opération de détente.
L'ISO 14113:2013 ne couvre pas les tuyaux souples en caoutchouc et en matière thermoplastique pour le soudage, le coupage et les techniques connexes.
L'ISO 14113:2013 ne s'applique pas aux gaz liquides cryogéniques ou aux gaz de pétrole liquéfiés (GPL).

Oprema za plamensko varjenje - Cevi in napeljave iz gume in umetnih snovi za tehnične pline do tlaka 450 bar (45 MPa) (ISO 14113:2013)

Ta mednarodni standard določa zahteve za cevi in napeljave iz gume in umetnih snovi za stisnjene, utekočinjene in raztopljene pline pri delovnem tlaku do 450 barov (45 MPa) in temperaturi okolice od –20 °C do +60 °C. Ta mednarodni standard velja za napeljave, ki se uporabljajo za priključitev tehničnih plinskih jeklenk na zbiralnike ali na snope pred zmanjšanjem tlaka. Ta mednarodni standard ne zajema cevi iz gume ali termoplastike za varjenje, rezanje in podobne postopke (glej ISO 3821 in ISO 12170). Ta mednarodni standard se ne uporablja za ohlajene utekočinjene pline ali utekočinjene naftne pline (LPG).

General Information

Status
Published
Publication Date
01-Oct-2013
Withdrawal Date
29-Apr-2014
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
02-Oct-2013
Completion Date
02-Oct-2013

Relations

Buy Standard

Standard
EN ISO 14113:2013
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2013
1DGRPHãþD
SIST EN ISO 14113:2009
2SUHPD]DSODPHQVNRYDUMHQMH&HYLLQQDSHOMDYHL]JXPHLQXPHWQLKVQRYL]D
WHKQLþQHSOLQHGRWODNDEDU 03D  ,62
Gas welding equipment - Rubber and plastics hose and hose assemblies for use with
industrial gases up to 450 bar (45 MPa) (ISO 14113:2013)
Gasschweißgeräte - Gummi- und Kunststoffschläuche und Schlauchleitungen für
Industriegase bis zu einem Druck von 450 bar (45 MPa) (ISO 14113:2013)
Matériel de soudage aux gaz - Tuyaux souples et flexibles en caoutchouc et en plastique
pour des gaz industriels jusqu'à 450 bar (45 MPa) (ISO 14113:2013)
Ta slovenski standard je istoveten z: EN ISO 14113:2013
ICS:
25.160.30 Varilna oprema Welding equipment
83.140.40 Gumene cevi Hoses
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 14113
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2013
ICS 25.160.30; 83.140.40 Supersedes EN ISO 14113:2008
English Version
Gas welding equipment - Rubber and plastics hose and hose
assemblies for use with industrial gases up to 450 bar (45 MPa)
(ISO 14113:2013)
Matériel de soudage aux gaz - Tuyaux souples et flexibles Gasschweißgeräte - Gummi- und Kunststoffschläuche und
en caoutchouc et en plastique pour des gaz industriels Schlauchleitungen für Industriegase bis zu einem Druck
jusqu'à 450 bar (45 MPa) (ISO 14113:2013) von 450 bar (45 MPa) (ISO 14113:2013)
This European Standard was approved by CEN on 3 September 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14113:2013: E
worldwide for CEN national Members.

Contents
Page
Foreword .3

Foreword
This document (EN ISO 14113:2013) has been prepared by Technical Committee ISO/TC 44 “Welding and
allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied processes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2014, and conflicting national standards shall be withdrawn at the
latest by April 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14113:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 14113:2013 has been approved by CEN as EN ISO 14113:2013 without any modification.

INTERNATIONAL ISO
STANDARD 14113
Third edition
2013-10-01
Gas welding equipment — Rubber
and plastics hose and hose assemblies
for use with industrial gases up to
450 bar (45 MPa)
Matériel de soudage aux gaz — Tuyaux souples et flexibles en caoutchouc
et en plastique pour des gaz industriels jusqu’à 450 bar (45 MPa)
Reference number
ISO 14113:2013(E)
©
ISO 2013
ISO 14113:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO 14113:2013(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Construction . 3
4.1 Hose . 3
4.2 End fittings . 3
4.3 Hose assemblies . 3
5 Dimensions and tolerances . 3
5.1 Bore size . 3
5.2 Concentricity. 3
5.3 Cut lengths and tolerances . 4
5.4 Length of hoses assemblies . 4
6 Physical properties of lining and cover — Type tests . 4
6.1 General . 4
6.2 Resistance to ignition requirement for oxygen hose lining . 5
6.3 Resistance to acetone (acetylene hose only). 5
7 Performance requirements — Type tests . 5
7.1 Pressure resistance requirements . 5
7.2 Adhesion (rubber hoses only) . 6
7.3 Flexibility . 6
7.4 Low temperature flexibility . 6
7.5 Ozone resistance (for hoses with an outer protective cover of rubber) . 6
7.6 UV resistance (for hoses with plastics cover) . 6
7.7 Permeability to gas . 6
7.8 Electrical conductivity . 6
7.9 End fitting integrity . 6
8 Performance requirements — Production tests . 7
8.1 Pressure tests for hose assemblies . 7
8.2 Leak test . 7
8.3 Cleaning for oxygen service . 7
9 Marking . 7
10 Packaging . 8
11 Instructions . 8
Annex A (normative) Acetylene decomposition test for hose assemblies used in high pressure
acetylene installations . 9
Annex B (normative) Oxygen pressure surge test
...............................................................................................................................10
Annex C (normative) Oxygen system installation considerations .12
Bibliography .13
ISO 14113:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents sh
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.