EN ISO 4413:2010

SLOVENSKI STANDARD
01-januar-2011
1DGRPHãþD
SIST EN 982:1998+A1:2008
Fluidna tehnika - Hidravlika - Splošna pravila in varnostne zahteve za fluidne
sisteme in njihove komponente (ISO 4413:2010)
Hydraulic fluid power - General rules and safety requirements for systems and their
components (ISO 4413:2010)
Fluidtechnik - Allgemeine Regeln und sicherheitstechnische Anforderungen an
Hydraulikanlagen und deren Bauteile (ISO 4413:2010)
Transmissions hydrauliques - Règles générales et exigences de sécurité relatives aux
systèmes et leurs composants (ISO 4413:2010)
Ta slovenski standard je istoveten z: EN ISO 4413:2010
ICS:
23.100.01 +LGUDYOLþQLVLVWHPLQDVSORãQR Fluid power systems in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 4413
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2010
ICS 23.100.01 Supersedes EN 982:1996+A1:2008
English Version
Hydraulic fluid power - General rules and safety requirements for
systems and their components (ISO 4413:2010)
Transmissions hydrauliques - Règles générales et Fluidtechnik - Allgemeine Regeln und sicherheitstechnische
exigences de sécurité relatives aux systèmes et leurs Anforderungen an Hydraulikanlagen und deren Bauteile
composants (ISO 4413:2010) (ISO 4413:2010)
This European Standard was approved by CEN on 6 November 2010.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4413:2010: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Annex ZA .4

Foreword
This document (EN ISO 4413:2010) has been prepared by Technical Committee ISO/TC 131 “Fluid power
systems” in collaboration with Technical Committee CEN/TC 114 “Safety of machinery” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2011, and conflicting national standards shall be withdrawn at the
latest by November 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 982:1996+A1:2008.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 4413:2010 has been approved by CEN as a EN ISO 4413:2010 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2006/42/EC on machinery.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard confers, within the limits of the scope of this standard, a presumption of conformity with the
relevant Essential Requirements, except Essential Requirements 1.5.8 and 1.7.4.2 u), of that Directive and
associated EFTA regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling
within the scope of this standard.
INTERNATIONAL ISO
STANDARD 4413
Third edition
2010-11-15
Hydraulic fluid power — General rules
and safety requirements for systems and
their components
Transmissions hydrauliques — Règles générales et exigences de
sécurité relatives aux systèmes et leurs composants

Reference number
ISO 4413:2010(E)
©
ISO 2010
ISO 4413:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved

ISO 4413:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 List of significant hazards .3
5 General rules and safety requirements.3
5.1 General .3
5.2 Basic requirements for the design and specification of hydraulic systems.3
5.3 Additional requirements .5
5.4 Specific requirements for components and controls.7
6 Verification of safety requirements and acceptance testing .26
7 Information for use.26
7.1 General requirements .26
7.2 Final information for systems on stationary industrial machinery.26
7.3 Maintenance and operating data .27
7.4 Marking and identification.28
8 Identification statement (reference to this International Standard) .30
Annex A (informative) List of significant hazards .31
Annex B (informative) Form for collecting hydraulic system and component data to ensure
conformance with ISO 4413 .33
Bibliography.45

ISO 4413:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4413 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 9,
Installations and systems.
This third edition cancels and replaces the second edition (ISO 4413:1998), which has been technically
revised, specifically with regards to the following:
a) integration of ISO 4413:1998 and EN 982:1996;
b) integration of safety requirements to comply with the European Machinery Directive 2006/42/EC;
c) updating of safety requirements, taking into account International Standards on machine safety.

iv © ISO 2010 – All rights reserved

ISO 4413:2010(E)
Introduction
This International Standard is a type B standard as defined in ISO 12100. The provisions of this International
Standard can be supplemented or modified by a type C standard. For machines that are covered by the scope
of a type C standard and that have been designed and built in accordance with the provisions of that standard,
the provisions of that type C standard take precedence over the provisions of this type B standard.
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an
enclosed circuit.
In the past, ISO 4413 was intended to provide assistance in the understanding between the supplier and the
purchaser. This edition of ISO 4413 now includes, in addition, general requirements for the engineering of a
hydraulic system and safety requirements that support the essential health and safety requirements of the
European Machinery Directive.
Equivalent requirements for pneumatic systems are defined in ISO 4414.

INTERNATIONAL STANDARD ISO 4413:2010(E)

Hydraulic fluid power — General rules and safety requirements
for systems and their components
1 Scope
This International Standard specifies general rule
...