EN ISO 2080:2022

SLOVENSKI STANDARD
01-maj-2022
Nadomešča:
SIST EN ISO 2080:2009
Kovinske in druge anorganske prevleke - Površinska obdelava kovinskih in drugih
anorganskih prevlek - Slovar (ISO 2080:2022)
Metallic and other inorganic coatings - Surface treatment, metallic and other inorganic
coatings - Vocabulary (ISO 2080:2022)
Metallische und andere anorganische Überzüge - Oberflächenbehandlung, metallische
und andere anorganische Überzüge - Wörterbuch (ISO 2080:2022)
Revêtements métalliques et autres revêtements inorganiques - Traitement de surface,
revêtements métalliques et autres revêtements inorganiques - Vocabulaire (ISO
2080:2022)
Ta slovenski standard je istoveten z: EN ISO 2080:2022
ICS:
01.040.25 Izdelavna tehnika (Slovarji) Manufacturing engineering
(Vocabularies)
25.220.40 Kovinske prevleke Metallic coatings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 2080
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2022
EUROPÄISCHE NORM
ICS 01.040.25; 25.220.40 Supersedes EN ISO 2080:2009
English Version
Metallic and other inorganic coatings - Surface treatment,
metallic and other inorganic coatings - Vocabulary (ISO
2080:2022)
Revêtements métalliques et autres revêtements Metallische und andere anorganische Überzüge -
inorganiques - Traitement de surface, revêtements Oberflächenbehandlung, metallische und andere
métalliques et autres revêtements inorganiques - anorganische Überzüge - Wörterbuch (ISO 2080:2022)
Vocabulaire (ISO 2080:2022)
This European Standard was approved by CEN on 8 January 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2080:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 2080:2022) has been prepared by Technical Committee ISO/TC 107 "Metallic
and other inorganic coatings" in collaboration with Technical Committee CEN/TC 262 “Metallic and
other inorganic coatings, including for corrosion protection and corrosion testing of metals and alloys”
the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2022, and conflicting national standards
shall be withdrawn at the latest by September 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2080:2009.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 2080:2022 has been approved by CEN as EN ISO 2080:2022 without any modification.

INTERNATIONAL ISO
STANDARD 2080
Fourth edition
2022-03
Metallic and other inorganic
coatings — Surface treatment, metallic
and other inorganic coatings —
Vocabulary
Revêtements métalliques et autres revêtements inorganiques —
Traitement de surface, revêtements métalliques et autres revêtements
inorganiques — Vocabulaire
Reference number
ISO 2080:2022(E)
ISO 2080:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 2080:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 General types of surface-finishing processes and treatments . 1
3.2 Terms used in the industry . 4
Bibliography .28
iii
ISO 2080:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 107, Metallic and other inorganic coatings,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 262, Metallic and other inorganic coatings, including for corrosion protection and corrosion testing of
metals and alloys, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 2080:2008), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— new terms have been introduced;
— previous entries have been rationalized;
— some entries have been deleted.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO 2080:2022(E)
Introduction
The terms and definitions in this document apply to electroplating and other related surface-finishing
processes. The terms and definitions are not necessarily arranged in English alphabetical order. Related
terms, giving different alternatives for a given process, have been grouped under a leading term, as, for
example, in the case of “chemical plating”, “electrodeposition”, “blasting”, “cleaning” or “colour anodized
aluminium”.
Basic terms and definitions relating to corrosion and electrochemical techniques used in corrosion
science are given in ISO 8044 and are not included. Basic terms used in chemistry, electrochemistry
or physics are also not included in this document. The definitions for such terms can be found in
handbooks or dictionaries of chemistry or physics.
v
INTERNATIONAL STANDARD ISO 2080:2022(E)
Metallic and other inorganic coatings — Surface treatment,
metallic and other inorganic coatings — Vocabulary
1 Scope
This document defines the terms related to the general types of surface-finishing processes. Emphasis
is placed on practical usage in surface-finishing technology in the metal-finishing field.
This document does not include terms for porcelain and vitreous enamel, thermally sprayed coatings
and galvanising for which specialized vocabularies and glossaries exist. For the most part, basic terms
that have the same meaning in surface finishing as in other fields of technology, and that are defined in
handbooks and dictionaries of chemistry and physics, are not included.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1 General types of surface-finishing processes and treatments
3.1.1
chemical plating
deposition of a metallic coating by chemical, non-electrolytic methods
3.1.1.1
autocatalytic plating
DEPRECATED: electroless plating
deposition of a metallic coating by a controlled chemical reduction that is catalysed by the metal or
alloy being deposited
3.1.1.2
contact plating
deposition of a metal by use of an internal source of current by immersing the work (3.2.218) in contact
with another metal in a solution containing a compound of the metal to be deposited
3.1.1.3
immersion coating
metallic coating produced by a displacement reaction in which one metal displaces another from a
solution
2+ 2+
EXAMPLE Fe + Cu → Cu + Fe
3.1.2
chemical vapour deposition
CVD
deposition of a coating by a chemical reaction, induced by heat or gaseous reduction of vapour
condensing on a substrate (3.2.205)
ISO 2080:2022(E)
3.1.3
conversion coating
conversion layer
coating obtained by conversion treatment (3.1.4)
3.1.4
conversion treatment
chemical or electrochemical process producing a superficial layer containing a compound of the
substrate (3.2.205) metal
EXAMPLE Passivation (3.2.163) coatings on zinc and zinc alloys; aluminium and phosphate coatings on steel;
chromate conversion coatings (3.2.72).
Note 1 to entry: Anodiz
...