iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 455-1:2000

(Main)

Medical gloves for single use - Part 1: Requirements and testing for freedom from holes

Medical gloves for single use - Part 1: Requirements and testing for freedom from holes

This part of this Standard specifies requirements and gives the test method for medical gloves for single use in order to determine freedom from holes. NOTE Attention is drawn to EN 374-1 "Protective gloves against chemicals and micro-organisms - Part 1: Terminology and performance requirements".

Medizinische Handschuhe zum einmaligen Gebrauch - Teil 1: Anforderungen und Prüfung auf Dichtheit

Diese Norm legt Anforderungen und Prüfung auf Dichtheit von medizinischen Handschuhen zum einmaligen Gebrauch fest. ANMERKUNG Zu beachten ist EN 374-1 "Schutzhandschuhe gegen Chemikalien und Mikroorganismen - Teil 1: Terminologie und Leistungsanforderungen".

Gants médicaux non réutilisables - Partie 1: Détection des trous - Prescriptions et essais

La présente partie de cette norme a pour objet de fixer les exigences qui s'appliquent à l'absence de trous dans les gants médicaux non réutilisables et aux méthodes d'essai correspondantes. NOTE L'attention est attirée sur l'exigence de l'EN 374-1 "Gants de protection contre les produits chimiques et les micro-organismes - Partie 1: Terminologie et performances requises".

Medicinske rokavice za enkratno uporabo - 1. del: Zahteve in preskusi za ugotavljanje odsotnosti lukenj

General Information

Status
Withdrawn
Publication Date
17-Oct-2000
Withdrawal Date
12-May-2020
ICS
13.340 - Protective equipment
Technical Committee
CEN/TC 205 - Non-active medical devices
Drafting Committee
CEN/TC 205/WG 3 - Medical gloves
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
13-May-2020
Directive
93/42/EEC - Council Directive 93/42/EEC of 14 June 1993 concerning medical devices
98/79/EC - Directive 98/79/EC of the European Parliament and of the Council of 27 October 1998 on in vitro diagnostic medical devices
Mandate
M/023 - Standardization mandate to CEN/CENELEC concerning the development of European standards relating to medical devices
Ref Project
SIST EN 455-1:2001 - Medical gloves for single use - Part 1: Requirements and testing for freedom from holes

Relations

Replaces
EN 455-1:1993/A1:1998 - Medical gloves for single use - Part 1: Requirements and testing for freedom from holes
Effective Date
22-Dec-2008
Replaces
EN 455-1:1993 - Medical gloves for single use - Part 1: Requirements and testing for freedom from holes
Effective Date
22-Dec-2008
Replaced By
EN 455-1:2020 - Medical gloves for single use - Part 1: Requirements and testing for freedom from holes
Effective Date
15-Jul-2018

Buy Standard

EN 455-1:2001EN 455-1:2001
PreviousNext
Standard
EN 455-1:2001
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-november-2001
1DGRPHãþD
SIST EN 455-1:2000
SIST EN 455-1:2000/A1:2000
Medicinske rokavice za enkratno uporabo - 1. del: Zahteve in preskusi za
ugotavljanje odsotnosti lukenj
Medical gloves for single use - Part 1: Requirements and testing for freedom from holes
Medizinische Handschuhe zum einmaligen Gebrauch - Teil 1: Anforderungen und
Prüfung auf Dichtheit
Gants médicaux non réutilisables - Partie 1: Détection des trous - Prescriptions et essais
Ta slovenski standard je istoveten z: EN 455-1:2000
ICS:
11.140 Oprema bolnišnic Hospital equipment
2003-01.Slovenski inštitut za standardizacijo. Raz
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
CEN/TS 16931-8:2024(Main)
Electronic invoicing - Part 8: Semantic data model of the elements of an e-receipt or a simplified electronic invoice
kSIST FprEN 16931-8:2024

This document establishes a semantic data model of an e-receipt or a simplified electronic invoice.
NOTE   In the remainder of this document, when “e-receipt” is mentioned, “simplified invoice” is also meant.
The semantic model includes essential information elements that an electronic receipt needs to ensure legal (including fiscal) compliance and to enable interoperability for cross-border, cross sector and domestic trade. The semantic model can be used by organizations in the private and the public sector for documenting by issuing a receipt for the purchase of services and /or goods. It can also be used for documenting a purchase between private sector enterprises. In addition, it has been designed for the use of consumers.

  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19403-5:2024(Main)
Paints and varnishes - Wettability - Part 5: Determination of the polar and dispersive fractions of the surface tension of liquids from contact angles measurements on a solid with only a disperse contribution to its surface energy (ISO 19403-5:2024)
kSIST FprEN ISO 19403-5:2024

This document specifies a test method to determine the polar and dispersive fractions of the surface tension of liquids by optical methods. The method can be applied for the characterization of liquid coating materials.
If applied to liquids with non-Newtonian flow behaviour (see ISO 3219-1:2021, 3.22), restrictions can apply.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16286-1:2024(Main)
Railway applications - Gangway systems between vehicles - Part 1: Main applications
SIST EN 16286-1:2024

This document specifies the technical and safety requirements applicable to gangway systems used in heavy rail and urban rail vehicles that are designed to allow passengers or staff to move between adjacent vehicles.
It also specifies:
- the requirements for the safety for passengers and/or staff in the gangway while the train is running,
- the assessment methods as well as pass/fail criteria for gangways installed on vehicles.
NOTE Some requirements in this document may not be applicable for gangways designed for use by staff only.
This document is not intended to specify requirements for articulation systems which can be an integral part of gangway systems.
This document is not applicable for rubber tube gangways and interconnecting gangways for coaches travelling at speeds of up to 200 km/h on high-speed lines with tunnel sections. Information about these types of gangway systems are given in Annex A and Annex B.

  • Draft
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17966:2024(Main)
Fire protection equipment - Carbon dioxide extinguishing systems for use on premises - Design and installation (ISO 6183:2022, modified)
SIST EN 17966:2024

This document specifies requirements and gives recommendations for the design, installation, testing, maintenance and safety of fixed carbon dioxide firefighting systems in buildings, plants or other structures. It is not applicable to extinguishing systems on ships, in aircraft, on vehicles or on mobile fire appliances, or to below ground systems in the mining industry; nor does it apply to carbon dioxide pre-inerting systems.
Design of systems where unclosable opening(s) of the protected volume exceed a specified area and where the opening(s) can be subject to the effect of wind is not specified, although general guidance on the procedure to be followed in such cases is given (see 7.4.3.2).

  • Draft
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21009-2:2024(Main)
Cryogenic vessels - Static vacuum-insulated vessels - Part 2: Operational requirements (ISO 21009-2:2024)
SIST EN ISO 21009-2:2024

This document specifies operational requirements for static vacuum insulated vessels designed for a maximum allowable pressure of more than 50 kPa (0,5 bar). It can also be used as a guideline for vessels designed for a maximum allowable pressure of less than 50 kPa (0,5 bar).
This document applies to vessels designed for cryogenic fluids specified in ISO 21009-1.
Static cryogenic vessels are often partly equipped by the manufacturer, but can be installed or re- installed by another party, such as the operator, user or owner.
NOTE 1        For the installation of these vessels, additional requirements can apply.
NOTE 2        Some requirements of this document can be covered by local regulations, e.g. safety distances, occupational safety and health.
NOTE 3        Additional requirements can apply to the operation of large scale and field-fabricated vessels.

  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19403-6:2024(Main)
Paints and varnishes - Wettability - Part 6: Measurement of dynamic advancing and receding angle by changing the volume of a drop (ISO 19403‑6:2024)
kSIST FprEN ISO 19403-6:2024

This document specifies a method to measure the dynamic contact angle with an optical method. The dynamic advancing and the dynamic receding contact angles are determined.
By using the measurement specified in this document, the wetting and dewetting properties can be characterized. The morphological and chemical homogeneity of interfaces can also be determined.

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17936:2024(Main)
Railway applications - Acoustics - Measurement of source terms for environmental noise calculations
SIST EN 17936:2024

This document addresses the measurement of source terms for environmental noise calculation for rail traffic (including light rail, such as trams, metros, etc.). It is applicable to the measurement of in-service trains on operational tracks.
It is not applicable to type acceptance testing of rolling-stock or tracks, or to derive source terms for time domain models.
The following rail traffic noise source types are in the scope:
-   rolling noise;
-   traction and equipment noise;
-   aerodynamic noise;
-   impact noise (e.g. rail joints, switch and crossings, wheel flats);
-   braking noise;
-   bridge noise;
-   squeal noise.
Noise from rail vehicles at standstill, such as stationary engine idling and auxiliary equipment at yards and stations, is covered by EN ISO 3095:2013 for measurement procedures and operating conditions, and by EN ISO 3740:2019 and EN ISO 3744 for the determination of sound power. It is therefore not in the scope of this document.
The calculation of the propagation of sound is part of generally standardized propagation models which are not addressed in this document.
Noise from fixed installations (e.g. stations, depots, electricity sub-stations) is not in the scope of this document.
Source terms are specific to a vehicle and track type. The scope includes measurement procedures and conditions and sampling requirements.

  • Draft
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19403-7:2024(Main)
Paints and varnishes - Wettability - Part 7: Measurement of the dynamic contact angles and the roll-off angle on a tilt stage (ISO 19403-7:2024)
kSIST FprEN ISO 19403-7:2024

This document specifies a method for the dynamic measurement of the roll-off angle on a tilt stage of a liquid drop on a solid surface. This document also specifies how the dynamic advancing and receding contact angles of the drop rolling off can be determined. The roll-off angle determined through this method can be applied when evaluating easy-to-clean or anti-adherent surfaces.

  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13172:2024(Main)
Thermal insulation products - Common evaluation rules
kSIST FprEN 13172:2024

This document specifies common evaluation rules useful for the assessment and verification of constancy of performance of a thermal insulation product with harmonised technical specifications, product standards and any other assessment documents. Harmonised technical specifications, product standards and other assessment documents are called European product specifications in this document.
This document applies to factory made products for buildings, factory made products for building equipment and industrial installations, in situ products for buildings, in situ products for building equipment and industrial installations, to products for civil engineering applications, and to external thermal insulation composite kits.

  • Draft
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16838:2024(Main)
Refrigerated display scooping cabinets and pozzetto for gelato - Classification, requirements, performance and energy consumption testing
kSIST FprEN 16838:2024

This document specifies classification, requirements for the construction, performance and energy consumption testing of:
-   gelato scooping cabinets used for sale and display of artisan and self-made gelato;
-   pozzetto used for sale of artisan and self-made gelato, without any display function.
It specifies test conditions and methods for checking that the requirements have been satisfied, their marking and the list of their characteristics to be declared by the manufacturer.

  • Draft
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day