97.220.20 - Winter sports equipment
ICS 97.220.20 Details
Winter sports equipment
Wintersportgerate
Équipements de sports d'hiver
Oprema za zimske športe
General Information
Frequently Asked Questions
ICS 97.220.20 is a classification code in the International Classification for Standards (ICS) system. It covers "Winter sports equipment". The ICS is a hierarchical classification system used to organize international, regional, and national standards, facilitating the search and identification of standards across different fields.
There are 349 standards classified under ICS 97.220.20 (Winter sports equipment). These standards are published by international and regional standardization bodies including ISO, IEC, CEN, CENELEC, and ETSI.
The International Classification for Standards (ICS) is a hierarchical classification system maintained by ISO to organize standards and related documents. It uses a three-level structure with field (2 digits), group (3 digits), and sub-group (2 digits) codes. The ICS helps users find standards by subject area and enables statistical analysis of standards development activities.
e-Library Subscription
Create subscription and get permanent access to documents within 97.220.20 - Winter sports equipment
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document defines terms for the specification of important characteristics of alpine skis, cross-country skis (XC-skis) and snowboards.
- Standard25 pagesEnglish languagesale 15% off
- Standard25 pagesFrench languagesale 15% off
This document specifies requirements, test methods and marking for alpine ski-boots with improved walking soles that are used with systems of alpine ski-bindings for improved walking soles with attachment at the boot front and boot rear, the proper release function of which depends on the dimensions and design of the interfaces. Alpine ski boots with improved walking soles are intended to a better walkability without affecting the function of the alpine ski binding designed for improved walking soles. This document is applicable to ski-boots of sizes 15,0 and larger [Types A (Adults) and C (Children)] in the Mondopoint system (see Annex A).
- Standard41 pagesEnglish languagesale 15% off
- Standard42 pagesFrench languagesale 15% off
This document specifies general requirements and test methods for head, face, eye, neck, and body protectors (hereafter referred to as protectors) for use in ice hockey.
This document is intended only for protectors used for ice hockey.
- Standard18 pagesEnglish languagee-Library read for1 day
This document specifies performance requirements and test methods for eye and face protectors for use in ice hockey only.
This document is applicable to eye and face protectors worn by ice hockey players other than goalkeepers and by referees.
- Standard37 pagesEnglish languagee-Library read for1 day
This document specifies performance requirements and test methods for head protectors for use in ice hockey.
This document is applicable to head protectors worn by ice hockey players excluding goalkeepers and by referees.
- Standard30 pagesEnglish languagee-Library read for1 day
This document specifies performance requirements and test methods for head and face protectors for use by ice hockey goalkeepers only.
- Standard24 pagesEnglish languagee-Library read for1 day
This document specifies general requirements and test methods for head, face, eye, neck, and body protectors (hereafter referred to as protectors) for use in ice hockey.
This document is intended only for protectors used for ice hockey.
- Standard18 pagesEnglish languagee-Library read for1 day
This document specifies performance requirements and test methods for head and face protectors for use by ice hockey goalkeepers only.
- Standard24 pagesEnglish languagee-Library read for1 day
This document specifies performance requirements and test methods for eye and face protectors for use in ice hockey only.
This document is applicable to eye and face protectors worn by ice hockey players other than goalkeepers and by referees.
- Standard37 pagesEnglish languagee-Library read for1 day
This document specifies performance requirements and test methods for head protectors for use in ice hockey.
This document is applicable to head protectors worn by ice hockey players excluding goalkeepers and by referees.
- Standard30 pagesEnglish languagee-Library read for1 day
This document specifies performance requirements and test methods for head and face protectors for use by ice hockey goalkeepers only.
- Standard12 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
This document specifies performance requirements and test methods for eye and face protectors for use in ice hockey only. This document is applicable to eye and face protectors worn by ice hockey players other than goalkeepers and by referees.
- Standard26 pagesEnglish languagesale 15% off
- Standard26 pagesFrench languagesale 15% off
This document specifies general requirements and test methods for head, face, eye, neck, and body protectors (hereafter referred to as protectors) for use in ice hockey. This document is intended only for protectors used for ice hockey.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
This document specifies performance requirements and test methods for head protectors for use in ice hockey. This document is applicable to head protectors worn by ice hockey players excluding goalkeepers and by referees.
- Standard18 pagesEnglish languagesale 15% off
- Standard18 pagesFrench languagesale 15% off
This document specifies the dimensions and characteristics of the interface, requirements, test methods and marking of ski-boots with a rigid ski boot sole that are used with current systems of touring ski-bindings with attachment at the boot toe and boot heel, the proper release function of which depends on the dimensions and design of the interfaces. This document is not necessarily applicable to touring ski boots that function independent of the sole shape with certain ski-binding systems. This document is applicable to ski-boots of sizes 15,0 and larger in the Mondopoint system (see Annex A). It is applicable to rigid touring boots. Boots with softer shells such as Telemark boots are excluded as they do not have the necessary shell stability to act as part of the release systems.
- Standard20 pagesEnglish languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
SIGNIFICANCE AND USE
2.1 A standard terminology is needed to allow freestyle terrain park designers, builders, ski resorts, accident investigators, and scientists to use a common language in describing freestyle terrain park jumps and related parameters for a jumper using the feature.
2.2 Angles are taken with respect to horizontal, with positive values indicating an increase in elevation and negative values indicating a decrease in elevation along the path of travel for a terrain park participant using the jump.
SCOPE
1.1 This terminology covers the terms required to describe a cross sectional profile of a snow sport freestyle terrain park jump and related parameters for a jumper using the feature and does not cover any other terrain park feature.
1.2 The terms are presented in a sequence considered to be the most logical with definitions presented later calling upon those presented earlier. This terminology standard does not require the use of any specific units; Imperial units (feet, seconds, degrees) or metric units (meters, seconds, degrees) can be used.
1.3 The depictions used in this standard are intended to aid in understanding the definitions and are not intended to depict or describe how any particular terrain park jump or its component features should be designed, built or maintained. Some terrain park jumps may use different configurations or combinations of features, or they may not incorporate all of the features depicted or defined in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with the use of snow sport terrain park features. Snow sports and the use of terrain park features involve inherent risks, and a terrain park feature that complies with all applicable standards or guidelines cannot eliminate all risks associated with terrain park features. Therefore, it is to be clearly understood that compliance with these applicable standards or guidelines in no way guarantees that injury can be prevented.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesEnglish languagesale 15% off
This document specifies assembly, adjustment and inspection procedures for the binding mechanisms of skis, integrating, in a practical way, the requirements of International Standards which are related to skis, bindings and boots. It is applicable to a ski-binding-boot system (S-B-B) for alpine skiing, of which at least one component is owned by the user. This document is applicable for complete and incomplete alpine ski-binding-boot systems which are owned by the user or rented for 15 days or more. NOTE ISO 13993 gives a method of measurement for equipment which is rented for less than 15 days.
- Standard14 pagesEnglish languagesale 15% off
- Standard16 pagesFrench languagesale 15% off
This document defines test soles representing - an alpine ski-boot (form A) or at least the bottom part of it used for testing alpine ski-bindings for alpine skiing in accordance with ISO 9462 and ISO 9465, and - a touring ski-boot (form T) or at least the bottom part of it used for testing touring ski-bindings for touring skiing in accordance with ISO 13992 and ISO 9465. This document also defines a test body representing alpine ski-boots with improved walking soles in accordance with ISO 23223. NOTE Ski-boots have their own International Standards (ISO 5355, ISO 9523 and ISO 23223), which allow relatively large tolerances in defining the test sole that are generally believed to be suitable for on-slope use by skiers, but too large for reproducible laboratory measurements.
- Standard10 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
This document specifies the main characteristics of ski-bindings and describes, as an example, test methods A and B. This document applies to ski-bindings for alpine skiing for children, juniors and adults.
- Standard41 pagesEnglish languagesale 15% off
- Standard42 pagesFrench languagesale 15% off
SIGNIFICANCE AND USE
5.1 This practice serves the purpose of measuring snow sports freestyle terrain jump features and may be used as a method for recreating jumps in the field or two-dimensional jump profiles of existing jumps.
SCOPE
1.1 This practice is intended to standardize field measurements of existing snow sport freestyle terrain park jumps. It does not cover other types of terrain park features or asymmetric jumps.
1.2 This practice is for measuring jumps that are used in public access snow sport freestyle terrain parks discussed in Terminology F3237.
1.3 For features with multiple takeoffs, each takeoff should be considered as an independent jump and measured according to this practice.
1.4 The depictions and terrain features used in this standard are intended to aid understanding the definitions and methods and are not intended to depict or describe how any particular terrain park jump or its component features should be designed, built or maintained. Some terrain park features may use components that are not depicted or described in this standard, or they may use different configurations or combinations of components, or they may not incorporate all of the components depicted or defined in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with the use of snow sport terrain park features. Snow sports and the use of terrain park features involve inherent risks, and a terrain park feature that complies with all applicable standards or guidelines cannot eliminate all risks associated with terrain park features. Therefore, it is to be clearly understood that compliance with these applicable standards or guidelines in no way guarantees that injury can be prevented.
1.6 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard4 pagesEnglish languagesale 15% off
SIGNIFICANCE AND USE
4.1 The purpose of this practice is to aid in providing the end user with an appropriately functioning ski/binding/boot system with appropriate release/retention values.
4.2 The definitions and ranges defined in this practice do not necessarily apply to procedures incorporating an inspection interval or schedule, in which such procedures are specified by the binding manufacturer. This practice is not intended to be a method for evaluating equipment design.
SCOPE
1.1 This practice provides procedures for inspection and adjustment of alpine ski/binding/boot systems, including ski binding systems designated as multi-norm bindings and those compatible with “improved walking soles.”
1.2 This practice should be followed for all ski/binding/boot systems, whether newly mounted or previously mounted, when work is performed on the system that may affect its release function, unless otherwise specified by the binding manufacturer in non-rental applications.
1.3 This standard is not applicable to ski/binding/boot rental systems, including incomplete systems, except when a customer intends to use his or her own skis/bindings with the shop’s boots (as provided in Subsection 7.3 of Practice F1064). For more information on ski/binding/boot rental shop practices, for both complete and incomplete systems, consult Practice F1064.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard9 pagesEnglish languagesale 15% off
- Standard9 pagesEnglish languagesale 15% off
This document applies to all goggles with plano lenses, intended for eye protection against hazards including ultraviolet and visible solar radiation, rain, snow and wind, during downhill skiing, snowboarding and other similar activities.
This document applies to downhill skiing and snowboarding goggles fitted with an insert to carry prescription lenses.
It specifies requirements and testing for materials, performance, marking of goggles and information to be supplied by the manufacturer.
Information on the selection and use of downhill skiing and snowboarding goggles is given in Annex A.
This document does not apply to
a) eye protectors for protection when operating or travelling on a motorized vehicle,
b) eye protectors for protection against optical radiation from artificial sources, such as those used in solaria,
c) eye protectors for direct observation of the sun, and
d) eye protectors intended for sports with unrelated hazards and risks.
- Standard34 pagesEnglish languagee-Library read for1 day
SIGNIFICANCE AND USE
5.1 This test method involves simulation in the laboratory of potential injury-producing loads that can occur in skiing, without implying the frequency or the magnitude of the danger. This test method does not include the simulation of all or part of a skier, and care must be taken not to confuse the values of moments measured by the test shaft with the loads subjected to the tibia of a skier under the same conditions.
SCOPE
1.1 This test method covers a procedure for the measurement of release moments of ski bindings under conditions where inertia loadings of the ski binding system are not significant.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard13 pagesEnglish languagesale 15% off
ABSTRACT
This document covers specifications and conformity assessment methods for new head and face protectors for ice hockey goaltenders, as offered for initial sale. This specification is intended to reduce the risk of injury associated with playing the position of goaltender in ice hockey. The protectors are classified according to types: Type I and Type II. Optical tests, shock attenuation tests, puck impact tests, penetration resistance tests, and neck strap retention test shall be performed to meet the requirements specified.
SCOPE
1.1 This performance specification2 covers performance requirements for ice hockey goaltender head and face protectors.
1.2 The intent of this performance specification is to reduce the risk of injury to the head and face of ice hockey goaltenders without compromising the form and appeal of the game.
1.3 This specification has requirements for: (1) materials, assembly, and design; (2) protected areas (coverage) and penetration resistance; (3) shock absorption; (4) puck impact resistance; (5) extensibility and strength of the chin strap and its attachment; and (6) optical quality.
1.4 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification15 pagesEnglish languagesale 15% off
- Technical specification15 pagesEnglish languagesale 15% off
This document applies to all goggles with plano lenses, intended for eye protection against hazards including ultraviolet and visible solar radiation, rain, snow and wind, during downhill skiing, snowboarding and other similar activities.
This document applies to downhill skiing and snowboarding goggles fitted with an insert to carry prescription lenses.
It specifies requirements and testing for materials, performance, marking of goggles and information to be supplied by the manufacturer.
Information on the selection and use of downhill skiing and snowboarding goggles is given in Annex A.
This document does not apply to
a) eye protectors for protection when operating or travelling on a motorized vehicle,
b) eye protectors for protection against optical radiation from artificial sources, such as those used in solaria,
c) eye protectors for direct observation of the sun, and
d) eye protectors intended for sports with unrelated hazards and risks.
- Standard34 pagesEnglish languagee-Library read for1 day
SIGNIFICANCE AND USE
5.1 The purpose of this practice is to aid in providing the end user with an appropriate functioning ski/binding/boot system and associated release/retention characteristics by providing the rental facility with an ongoing program for monitoring the appropriateness of functional characteristics of the system. It is assumed that these procedures are integrated into the maintenance and operating procedures specified by the equipment manufacturers (for example, in manufacturer-provided technical manuals). This practice is not intended to create additional or redundant requirements for the rental facility. However, this practice should be the basis for the development of rental procedures if the equipment manufacturer’s maintenance and operating procedures do not specifically state that they are in compliance with this practice. This practice will aid the rental facility in providing the end user with a system that provides appropriate release/retention characteristics.
5.2 This practice is applicable to rental facilities that use releasable alpine ski bindings. It is not intended as a method for evaluating equipment designs or types, such as alpine touring equipment. Mixing components of different system types (for example, using an alpine touring boot in an alpine binding) is discouraged.
SCOPE
1.1 This practice establishes a uniform method for the sampling and inspection of complete and incomplete Alpine ski/binding/boot systems used in rental operations. This practice is appropriate for use in rental applications in which all or part of the functional components of the system are supplied by the rental facility.
1.2 This practice should be followed by any facility that rents complete or incomplete Alpine ski/binding/boot systems to an end user.
1.3 This practice is not intended for use with other ski boot or bindings systems, such as alpine touring or pin/tech systems. Use of ski boots or ski bindings that do not meet the requirements for alpine ski equipment can cause unexpected release and retention characteristics.
1.4 This standard does not apply to a ski/binding/boot system that is rented to one individual for the majority of a season and not returned to the rental inventory until the end of the season (often referred to as a seasonal rental); such systems will follow the practice provided in Practice F1063.
Note 1: Refer to Practice F1063 for equivalent procedures and tolerances for retail systems.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard11 pagesEnglish languagesale 15% off
- Standard11 pagesEnglish languagesale 15% off
SIGNIFICANCE AND USE
2.1 A standard set of definitions is needed to allow manufacturers, consumers, retailers, and scientists to use a common language in describing Alpine skis.
SCOPE
1.1 This terminology covers the terms required to describe the geometry of Alpine skis and does not cover special purpose skis.
1.2 The terms are presented in a sequence considered to be the most logical, with definitions presented later calling upon those presented earlier.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard2 pagesEnglish languagesale 15% off
This document specifies requirements, test methods and marking for alpine ski-boots with improved walking soles that are used with systems of alpine ski-bindings for improved walking soles with attachment at the boot front and boot rear, the proper release function of which depends on the dimensions and design of the interfaces. Alpine ski boots with improved walking soles are intended to a better walkability without affecting the function of the alpine ski binding designed for improved walking soles. This document is applicable to ski-boots of sizes 15,0 and larger (Types A (Adults) and C (Children)) in the Mondo point system (see Annex A).
- Standard41 pagesEnglish languagesale 15% off
- Standard42 pagesEnglish languagesale 15% off
- Standard42 pagesFrench languagesale 15% off
- Standard43 pagesFrench languagesale 15% off
This document applies to all goggles with plano lenses, intended for eye protection against hazards including ultraviolet and visible solar radiation, rain, snow and wind, during downhill skiing, snowboarding and other similar activities. This document applies to downhill skiing and snowboarding goggles fitted with an insert to carry prescription lenses. It specifies requirements and testing for materials, performance, marking of goggles and information to be supplied by the manufacturer. Information on the selection and use of downhill skiing and snowboarding goggles is given in Annex A. This document does not apply to a) eye protectors for protection when operating or travelling on a motorized vehicle, b) eye protectors for protection against optical radiation from artificial sources, such as those used in solaria, c) eye protectors for direct observation of the sun, and d) eye protectors intended for sports with unrelated hazards and risks.
- Standard22 pagesEnglish languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
SIGNIFICANCE AND USE
2.1 A standard set of definitions is needed to allow producers, dealers, users, consumers, general interest individuals, and consultants to use a common language for describing snowboards, snowboard bindings, and snowboard boots.
SCOPE
1.1 This terminology covers terms used to describe the geometry and common hardware used on snowboards (skis), snowboard bindings, and snowboard boots.
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard3 pagesEnglish languagesale 15% off
SIGNIFICANCE AND USE
4.1 This test method provides a means for determining the mass and moment of inertia of adult Alpine skis. It is not intended to evaluate data with regard to the quality of the ski.
SCOPE
1.1 This test method covers test measurement methods for mass and moment of inertia of adult Alpine skis.2
1.2 No limitation to ski size is proposed. This test method is applicable to all adult Alpine skis.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard3 pagesEnglish languagesale 15% off
This document specifies the requirements and test methods for ergonomics, innocuousness, comfort/sizing, restraint, ability to limit wrist extension and attenuate impact force on the palm as well as provisions for marking and instructions supplied by the manufacturer for wrist protectors for all users of snowboard equipment.
It does not apply to protectors used in roller sports, alpine skiing, or other sports. This document does not address protection for the forearm due to axial forces caused by an impact on the fingers or fist. Moreover, this document does not address protection against palmar flexion (terminal flexion) caused by an impact on the dorsal side of the hand.
- Standard24 pagesEnglish languagee-Library read for1 day
This document defines the minimum requirements for safety in poles for alpine and touring skiing. It specifies test methods to check conformity with these requirements. It is applicable to ski-poles for alpine and touring skiing in the following ranges of total length, lT: - group A, lT ≥ 1 050 mm (adults' poles); - group B, 1 050 mm > lT ≥ 700 mm (junior poles); - group C, lT
- Standard18 pagesEnglish languagesale 15% off
- Standard18 pagesFrench languagesale 15% off
This document specifies the requirements and test methods for ergonomics, innocuousness, comfort/sizing, restraint, ability to limit wrist extension and attenuate impact force on the palm as well as provisions for marking and instructions supplied by the manufacturer for wrist protectors for all users of snowboard equipment.
It does not apply to protectors used in roller sports, alpine skiing, or other sports. This document does not address protection for the forearm due to axial forces caused by an impact on the fingers or fist. Moreover, this document does not address protection against palmar flexion (terminal flexion) caused by an impact on the dorsal side of the hand.
- Standard24 pagesEnglish languagee-Library read for1 day
This document specifies the requirements and test methods for ergonomics, innocuousness, comfort/sizing, restraint, ability to limit wrist extension and attenuate impact force on the palm as well as provisions for marking and instructions supplied by the manufacturer for wrist protectors for all users of snowboard equipment. It does not apply to protectors used in roller sports, alpine skiing, or other sports. This document does not address protection for the forearm due to axial forces caused by an impact on the fingers or fist. Moreover, this document does not address protection against palmar flexion (terminal flexion) caused by an impact on the dorsal side of the hand.
- Standard14 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
ABSTRACT
This specification covers requirements for devices used to determine the release moments of ski equipment in retail sales and rental facilities; it is applicable to the manufacture, repair, and calibration of such devices. Classification: Type I-a device capable of indicating both positive and negative release moments (Mz); Type IA-a device type I with specified limits of linear displacement or angular deflection; Type IB-a type I device limited in use to a specified binding or group of bindings; Type II-a device capable of indicating both positive and negative release moments (My); Type IIA-a type II device with specified limits of linear displacement or angular deflection; Type IIB-a type II device limited in use to a specified binding or group of bindings; and Type III-a device other than type I or type II with specified capability. The test device shall be of a design such that when tested will meet the requirements prescribed. If the device is designed to indicate force, and a distance measurement is required to calculate the moment, the magnitude of the smallest increment of the distance measurement shall not be greater than 5 % of the shortest measurement anticipated.
SCOPE
1.1 This specification covers requirements for devices used to determine the release moments of ski equipment in retail sales and rental facilities.
1.2 This specification is applicable to the manufacture, repair, and calibration of such devices.
1.3 This specification is to be used with Test Method F1062.
1.4 The values expressed in newton metres, newtons, and centimetres are to be regarded as the standard.
1.5 The values expressed in units of torque may be converted to the appropriate force values when devices that indicate force are used.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification3 pagesEnglish languagesale 15% off
SIGNIFICANCE AND USE
4.1 This test method is intended for use in evaluating the binding to snowboard insert retention strength resulting from use. This test method may also be used to compare the durability of different materials and designs. This test method references ISO 10958-2, which is considered satisfactory for acceptance testing insert retention for snowboards.
SCOPE
1.1 This test method covers the requirements and test method for snowboards with channel-mounting systems on which bindings are attached to the board by means of a removable insert and screws.
1.2 This test method does not apply to snowboards for children with a mass less than 25 kg. It contains data for the manufacturer of snowboards, bindings, and retention devices concerning dimensions, tests, and other specifications for the binding mounting area.
1.3 For snowboards with fixed inserts, see ISO 10958-2.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard3 pagesEnglish languagesale 15% off
ABSTRACT
This test method covers the determination of center spring constant, forebody spring constant, and afterbody spring constant of Alpine skis. In addition, it covers a method for determination of the spring constant balance. The apparatuses shall be center spring constant equipment and forebody and afterbody spring constant equipment.
SCOPE
1.1 This test method covers the determination of center spring constant, forebody spring constant, and afterbody spring constant of Alpine skis. In addition, it covers a method for determination of the spring constant balance.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesEnglish languagesale 15% off
This document specifies methods for the selection of the release torques for alpine ski-bindings. It gives information necessary to determine the release torques recommended for use by ski-binding manufacturers in their instructions for installation and use, and by ski shops for the adjustment of ski-bindings already mounted. It is applicable to state-of-the-art alpine ski bindings. It might be inappropriate for non-mechanical bindings or bindings used with boots which reach more than half-way up the lower leg. This document describes a specified method for the selection of the recommended release torques considering three types of skiers. The method applies to moment-measuring binding test machines, according to ISO 11110.
- Standard5 pagesEnglish languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
This document specifies test methods for screws used for fastening ski bindings to alpine skis. NOTE 1 Acceptance criteria are specified in ISO 6004. The results of these test methods characterize the properties of the binding screw. NOTE 2 A test method for the mounting and fastening characteristics of different ski models is specified in ISO 8364.
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
This document specifies the requirements, test methods and marking of ski-boots which are used with current systems of alpine ski-bindings with attachment at the boot toe and boot heel, the proper release function of which depends on the dimensions and design of the interfaces. For ski-binding systems that function irrespective of the sole shape or that have different requirements for the sole dimensions, it is not always necessary for the ski-boot soles to comply with this document in order to achieve the desired degree of safety. It applies to ski-boots of sizes 15,0 and larger [types A (for adults) and C (for children)] in the Mondopoint system (see Annex A).
- Standard30 pagesEnglish languagesale 15% off
- Standard31 pagesFrench languagesale 15% off
This document specifies a uniform method for the sampling and inspection of complete and incomplete alpine ski-binding-boot systems used in rental operations. This document is intended for any facility which rents complete and incomplete alpine ski-binding-boot systems as for example when the skier owns the boots. This document is not applicable for alpine touring ski-binding-boot systems. This document is not applicable for complete and incomplete alpine ski-binding-boot systems which are rented for 15 days or more. NOTE 1 A period of less than 15 days is common for equipment being rented. NOTE 2 ISO 11088 gives a method for testing if the equipment is owned or rented for 15 days or more.
- Standard16 pagesEnglish languagesale 15% off
ABSTRACT
This practice establishes procedures for the selection of release torque values for Alpine ski/boot/binding systems. The recommended release torque is chosen based on skier type, age, and other factors such as adjustments for normal, discretionary, and release/retention settings. Also discussed are methods of selecting skier type, determining skier code, and determining release torque value. Procedures discussed in this practice may be used by ski binding manufacturers in their instructions for installation and use and by ski shops for making adjustments on already mounted ski bindings. However, this practice does not cover nonmechanical bindings or bindings used with boots that reach more than halfway up the lower leg.
SCOPE
1.1 This practice provides procedures for the selection of release torque values for Alpine ski/boot/bindings systems. These procedures may be used by ski binding manufacturers in their instructions for installation and use and by ski shops for the adjustment of already mounted ski bindings.
1.2 This practice is applicable to releasable Alpine ski/boot/binding systems.
1.3 Release torque values selected using this practice may not be appropriate for circumstances in which:
1.3.1 The skier carries an object that significantly increases the skier's effective body weight,
1.3.2 The skier grasps or in some manner controls an object such as a sled, or
1.3.3 The skier encounters exceptional snow or terrain conditions not commonly found on developed ski slopes.
1.4 This practice may be inappropriate for non-mechanical bindings or bindings used with boots that reach more than half way up the lower leg.
1.5 Release torque values outside the recommendations of this practice may increase the risk of injury to the skier. However, skiers who are informed of this potential risk may request such settings and have them provided, subject to any guidelines and limitations specified by the binding manufacturer.
1.6 These values refer to recommended release torque for initial adjustment of a ski binding and subsequent readjustment of the binding during routine maintenance or following a suspected malfunction. However, these values are not intended to apply to the condition of the equipment at any time after it is put into use.
1.6.1 For information concerning applicable tolerances to be used for the adjustment and inspection of releasable Alpine ski bindings in retail operations consult Practice F1063; for rental applications consult Practice F1064.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesEnglish languagesale 15% off
ISO 7138:2017 specifies laboratory measurement methods for mass and location of the balance point of cross-country skis.
If laboratory measurement data are determined and published by manufacturers or other institutions, standard measurement procedures can be used to ensure comparability.
ISO 7138:2017 is not the purpose of this document to evaluate the measurement data with regard to their influence on the quality of the ski.
- Standard7 pagesEnglish languagee-Library read for1 day
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
ISO 7139:2017 specifies laboratory measurement methods to determine the elastic properties of cross-country skis. Its purpose is to calculate the resistance of defined parts of the ski to bending.
ISO 7139:2017 applies to cross-country skis with a nominal length greater than or equal to 150 cm.
The standard measurement procedures can be used to ensure comparability between laboratory measurement data, determined and published by ski manufacturers, institutions or others.
In ISO 7139:2017, no attempt is made to relate the measurement data to the quality of the ski
- Standard8 pagesEnglish languagee-Library read for1 day
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
ISO 7798:2017 specifies a method for the determination of the fatigue indexes of cross-country skis (i.e. the resistance of the skis to changes of bottom camber height or irreversible damage) after a bending test with cyclic loading.
ISO 7798:2017 is applicable to cross-country skis with a nominal length of 160 cm to 215 cm.
- Standard11 pagesEnglish languagee-Library read for1 day
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
ISO 10045:2017 specifies the dimensions, mechanical properties and fastening characteristics of test screws used for testing the binding mounting area of alpine skis.
- Standard4 pagesEnglish languagesale 15% off
- Standard9 pagesEnglish languagee-Library read for1 day
- Standard4 pagesFrench languagesale 15% off
ISO 6003:2017 specifies laboratory measurement methods for mass and polar moment of inertia of alpine skis.
If laboratory measurement data are determined and published by the ski manufacturer or other institutions, standard measurement procedures can be used to ensure comparability.
ISO 6003:2017 also specifies a tolerance range which can be met by the measurement data of all manufactured skis, if for the specific model length measurement data are published by the manufacturer of the ski.
NOTE The appropriate ski length can be given with the published measurement data.
ISO 6003:2017 is not the purpose of this document to evaluate the measurement data with regard to their influence on the quality of the ski.
- Standard6 pagesEnglish languagesale 15% off
- Standard10 pagesEnglish languagee-Library read for1 day
- Standard6 pagesFrench languagesale 15% off
SIGNIFICANCE AND USE
4.1 This test method provides information concerning the resistance of a ski to permanent bending and an indication of its basic strength. It is not intended to evaluate the data with regard to the quality of the ski.
SCOPE
1.1 This test method covers the determination of linear deformation load and breaking load for Alpine skis.2
1.2 This test method is applicable to all Alpine skis.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard3 pagesEnglish languagesale 15% off
SIGNIFICANCE AND USE
4.1 This test method describes the steps required to evaluate a step-in snowboard binding system function. The test method consists of a series of laboratory tests that evaluate resistance to static and dynamic loading, function under cold and icy conditions, impact and fatigue behavior and assessment of potential false positive release. All tests must be passed.
4.2 All possible strains on the boot can be attributed to one torque M and one force F each on every axis X, Y, Z of a system of coordinates (see Fig. 1). The point of origin of the coordinates is agreed to be in the center of the ankle joint which is located approximately 100 mm from the plantar surface and 80 mm from the back of the heel.
FIG. 1 Torques and Forces
4.3 The torques and forces illustrated in the drawing in Fig. 1 are positive. The corresponding parameters acting in opposite direction are given negative signs. The arrowheads indicate the sense of rotation of the snowboard boot movement.
SCOPE
1.1 This test method specifies the essential requirements for a snowboard step-in binding—boot system (see 3.1.2); hereafter referred to as step-in snowboard bindings.
1.2 This test method is applicable to step-in snowboard bindings for adults and children. This type of binding system utilizes a mechanical interlocking mechanism, and the interlock mechanism of the system will be specific to the particular manufacturer. Compatibility between different systems is not expected or anticipated thus each potential combination of boot and binding requires testing.
1.3 For snowboard boots interfacing with ski binding, see ISO 11634.
1.4 For snowboard plate bindings, see ISO 14790.
1.5 For snowboard strap bindings made for soft boots, see ISO 14573.
1.6 For snowboard step-in bindings, see ISO 15344.
1.7 This standard does not address how or under what circumstances a snowboard binding with programmable release modes should release in its intended modes nor does it address the safety, desirability, or efficacy of any programmable release mode for snowboard bindings; any testing of such bindings to this standard must be performed with the release modes disabled or adjusted to their highest release value.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard4 pagesEnglish languagesale 15% off