EN ISO 10256-4:2024

SLOVENSKI STANDARD
oSIST prEN ISO 10256-4:2022
01-januar-2022
Varovalna oprema za uporabo pri hokeju na ledu - 4. del: Zaščita glave in obraza
za vratarje (ISO/DIS 10256-4:2021)
Protective equipment for use in ice hockey - Part 4: Head and face protection for
goalkeepers (ISO/DIS 10256-4:2021)
Schutzausrüstung zum Gebrauch beim Eishockey - Teil 4: Kopf- und Gesichtsschutz für
Torhüter (ISO/DIS 10256-4:2021)
Équipements de protection destinés à être utilisés en hockey sur glace - Partie 4:
Protections de tête et de visage pour les gardiens de but (ISO/DIS 10256-4:2021)
Ta slovenski standard je istoveten z: prEN ISO 10256-4
ICS:
13.340.20 Varovalna oprema za glavo Head protective equipment
97.220.20 Oprema za zimske športe Winter sports equipment
oSIST prEN ISO 10256-4:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN ISO 10256-4:2022
oSIST prEN ISO 10256-4:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 10256-4
ISO/TC 83/SC 5 Secretariat: SCC
Voting begins on: Voting terminates on:
2021-11-16 2022-02-08
Protective equipment for use in ice hockey —
Part 4:
Head and face protection for goalkeepers
ICS: 97.220.20; 13.340.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 10256-4:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2021

oSIST prEN ISO 10256-4:2022
ISO/DIS 10256-4:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
oSIST prEN ISO 10256-4:2022
ISO/DIS 10256-4:2021(E)
Contents Page
Foreword .v
European foreword . vi
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 2
4.1 Materials and construction . 2
4.1.1 General . 2
4.1.2 Types of goalkeeper head and face protectors . 2
4.2 Design . 2
4.2.1 Welded wire component . 2
4.2.2 Obstruction of vision . 2
4.2.3 Airway access . 3
4.2.4 Overlap . 3
4.2.5 Maximum distance (headform to face protector) . 3
4.2.6 Minimum load bearing area . 3
4.3 Protected area . 3
4.3.1 Protected area of the head . 3
4.3.2 Protected area of the face . 3
4.4 Penetration (test blade/disk) . 3
4.4.1 General . 3
4.4.2 Type D1 . 3
4.4.3 Type D3 . 3
4.5 Shock-absorbing capacity . 3
4.6 Puck impact resistance . 4
4.6.1 Contact test . 4
4.6.2 Toughness test . 4
4.7 Retention system . 4
4.8 Field of vision . 4
5 Test methods . 5
5.1 General . 5
5.1.1 Tolerances . 5
5.1.2 Samples . 5
5.1.3 Complete goalkeeper protector assembled from separate head and face
protectors . 5
5.2 Conditioning. 5
5.3 Goalkeeper protector positioning . 5
5.3.1 Helmet-positioning index (HPI) . 5
5.3.2 Placing and adjusting goalkeeper protector . 5
5.4 Protected area (coverage) test . 5
5.4.1 Protected area of the head . 5
5.4.2 Protected area of the face . 5
5.5 Penetration test . 6
5.5.1 General . 6
5.5.2 Penetration test over the protected area of the head . . 6
5.5.3 Penetration test over the protected area of the face . 6
5.6 Shock absorbing capacity test . . 6
5.7 Puck impact resistance test . 6
5.8 Retention system . 6
5.9 Field of vision . 7
6 Test report . 7
iii
oSIST prEN ISO 10256-4:2022
ISO/DIS 10256-4:2021(E)
7 Markings . 7
8 Information for users . 7
ANNEX ZA (informative) Relationship between this European Standard and the essential
requirements of Annex II of Regulation (EU) 2016/425 of the European Parliament
and of the Council of 9 March 2016 on personal protective equipment aimed to be
covered, .13
iv
oSIST prEN ISO 10256-4:2022
ISO/DIS 10256-4:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particula
...