77.150.20 - Magnesium products

ASTM B557M-15(2023)(Test Method)

Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)

SIGNIFICANCE AND USE
4.1 Tension tests provide information on the strength and ductility of materials under uniaxial tensile stresses. This information may be useful in comparisons of materials, alloy development, quality control, and design under certain circumstances.
4.2 The results of tension tests of specimens machined to standardized dimensions from selected portions of a part or material may not totally represent the strength and ductility properties of the entire end product or its in-service behavior in different environments.
4.3 These test methods are considered satisfactory for acceptance testing of commercial shipments and have been used extensively in the trade for this purpose.
SCOPE
1.1 These test methods cover the tension testing of wrought and cast aluminum- and magnesium-alloy products, with the exception of aluminum foil,2 and are derived from Test Methods E8M, which cover the tension testing of all metallic materials.
Note 1: These metric test methods are the equivalents of those in Test Methods B557, and are compatible in technical content except for the requirement of longer gage lengths for round specimens.
Note 2: Foil is sheet metal less than 0.20 mm thick. There is an overlap in the thickness range 0.15 mm to 0.20 mm defined for foil and sheet. Sheet products in this thickness range are supplied to sheet product specifications and foil products in this thickness range are supplied to foil product specifications. Exceptions to the provisions of these test methods may need to be made in individual specifications or test methods for a particular material.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard
15 pages
English language
sale 15% off

31-Mar-2023
77.150.10
77.150.20
B07

ASTM B80-23(Specification)

Standard Specification for Magnesium-Alloy Sand Castings

ABSTRACT
This specification covers magnesium-alloy sand castings. The castings shall conform to the chemical composition limits specified. The castings may be subjected to such heat treatment as deemed necessary to produce material that will conform to the requirements specified. Heat treatment shall be performed on the whole casting and never on a portion. Foundry control shall consist of examination of the castings by radiographic or other approved methods for determining internal discontinuities until the gating, pouring, and other foundry practices have been established to produce castings meeting the quality standards. The tension test specimens representing the castings shall conform to the requirements.
SCOPE
1.1 This specification covers magnesium-alloy sand castings designated as shown in Table 1.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values in parentheses are provided for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Technical specification
12 pages
English language
sale 15% off
Technical specification
12 pages
English language
sale 15% off

31-Mar-2023
77.150.20
B07

ASTM B557-15(2023)(Test Method)

Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products

SIGNIFICANCE AND USE
4.1 Tension tests provide information on the strength and ductility of materials under uniaxial tensile stresses. This information may be useful in comparisons of materials, alloy development, quality control, and design under certain circumstances.
4.2 The results of tension tests of specimens machined to standardized dimensions from selected portions of a part or material may not totally represent the strength and ductility properties of the entire end product or its in-service behavior in different environments.
4.3 These test methods are considered satisfactory for acceptance testing of commercial shipments and have been used extensively in the trade for this purpose.
SCOPE
1.1 These test methods cover the tension testing of wrought and cast aluminum- and magnesium-alloy products, with the exception of aluminum foil,2 and are derived from Test Methods E8, which cover the tension testing of all metallic materials.
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: Foil is sheet metal less than 0.0079 in. thick. There is an overlap in the thickness range 0.006 to 0.0079 in. defined for foil and sheet. Sheet products in this thickness range are supplied to sheet product specifications and foil products in this thickness range are supplied to foil product specifications. Exceptions to the provisions of these test methods may need to be made in individual specifications or test methods for a particular material.
Note 2: A complete metric companion to Test Methods B557 has been developed—Test Methods B557M; therefore, no metric equivalents are presented in these test methods.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard
15 pages
English language
sale 15% off

31-Mar-2023
77.150.10
77.150.20
B07

ASTM B107/B107M-13(2021)(Specification)

Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire

ABSTRACT
This specification covers magnesium-alloy extruded bars, rods, profiles, tubes, and wire. The bars, rods, profiles, tubes, or wire shall conform to the chemical requirements specified. Tensile properties such as tensile strength, yield strength, and elongation of magnesium alloys shall be determined. All material shall be of uniform quality, free from injurious surface defects, and shall have a workmanlike finish.
SCOPE
1.1 This specification covers magnesium-alloy extruded bars, rods, profiles, tubes, and wire of the composition given in Table 1.
1.2 The values stated in either inch-pound or SI units are to be regarded separately as standards. The SI units are shown in brackets or in separate tables or columns. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.
1.3 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Technical specification
19 pages
English language
sale 15% off

30-Nov-2021
77.150.20
B07

SIST ISO 16220:2021(Main)

Magnesium and magnesium alloys -- Magnesium alloy ingots and castings

ISO 16220:2017

ISO 16220:2017 specifies the chemical composition of magnesium alloy ingots and castings. It also specifies the mechanical properties of separately cast samples of these alloys (see Clause 7). By agreement, it also specifies the mechanical properties of magnesium alloy castings determined from samples cut from a casting.

Standard
23 pages
English language
e-Library read for
AI-Chat
1 day
Standard
18 pages
English language
sale 15% off

ASTM B93/B93M-21(Specification)

Standard Specification for Magnesium Alloys in Ingot Form for Sand Castings, Permanent Mold Castings, and Die Castings

ABSTRACT
This specification covers magnesium alloys in ingot form for remelting for the manufacture of sand castings, permanent mold castings, investment castings, and die castings. The chemical composition shall conform to the requirements and limits prescribed in the specification. Samples for the chemical analysis may be taken from the molten metal when the ingot is poured or from the ingots.
SCOPE
1.1 This specification covers magnesium alloys in ingot form for remelting for the manufacture of sand castings, permanent mold castings, investment castings, and die castings.
Note 1: Supplementary information pertaining to the alloys covered by this specification when used in the form of castings is given in Specifications B80, B94, B199, and B403.
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Technical specification
4 pages
English language
sale 15% off
Technical specification
4 pages
English language
sale 15% off

30-Apr-2021
77.150.20
B07

ASTM B90/B90M-21(Specification)

Standard Specification for Magnesium-Alloy Sheet and Plate

ABSTRACT
This specification covers magnesium-alloy sheet and plate designated as AZ31B in temper types O, H24, and H26. The sheet and plate shall conform to the chemical composition requirements prescribed for magnesium, aluminum, manganese, zinc, calcium, copper, iron, nickel and silicon, and shall meet the specified requirements for the tensile properties such as tensile strength, yield strength, and elongation for the corresponding specified thickness. Requirements for chemical analysis and tensile test including sampling are detailed.
SCOPE
1.1 This specification covers magnesium alloys in sheet and plate form designated as shown in Table 1.
1.2 The values stated in either inch-pound or SI units are to be regarded separately as standards. The SI units are shown in brackets or in separate tables or columns. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.
1.3 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Technical specification
6 pages
English language
sale 15% off
Technical specification
6 pages
English language
sale 15% off

30-Apr-2021
77.150.20
B07

ASTM B403-20(Specification)

Standard Specification for Magnesium-Alloy Investment Castings

ABSTRACT
This specification covers magnesium-alloy investment castings designated as AM100A, AZ81A, AZ91C, AZ91E, AZ92A, EQ21A, EZ33A, K1A, QE22A, ZE41A, and ZK61A. Sufficient stock shall be allowed for shrinkage and, where required, for finishing; but castings of excessive weight shall not be furnished. The castings shall conform to the chemical composition requirements prescribed for magnesium, aluminum, manganese, zinc, zirconium, rare earth elements, copper, nickel, silicon, iron, and other impurities, as determined by chemical analysis, and shall meet the specified requirements for the tensile properties such as tensile strength, yield strength, and elongation. Requirements for heat treatment and tensile test are detailed. The castings shall be of uniform quality and condition, free from cracks and other injurious defects, shall be cleaned before inspection by blasting or other approved process, and shall not be repaired by welding, impregnation, peening, or other method unless it is required.
SCOPE
1.1 This specification covers magnesium-alloy investment castings designated as shown in Table 1.
1.2 Alloy designations are in accordance with Practice E527; temper designations are in accordance with Practice B296.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Technical specification
4 pages
English language
sale 15% off
Technical specification
4 pages
English language
sale 15% off

31-Oct-2020
77.150.20
B07

Magnesium and magnesium alloys - Magnesium alloy ingots and castings

EN 1753:2019(Main)

SIST EN 1753:2019

This document defines the grades and the corresponding requirements for cast alloyed magnesium materials.
This document specifies 2 groups of magnesium alloy grades by a classification based on the chemical composition. The first group deals with grades for magnesium alloy ingots. The second group deals with grades for magnesium alloy castings.
This document also specifies mechanical properties measured on test pieces machined from cast samples.
This document does not cover technical delivery conditions for magnesium alloy castings (see EN 1559-1 [7] and EN 1559-5 [8]).

Standard
31 pages
English language
e-Library read for
AI-Chat
1 day

24-Sep-2019
30-Mar-2020
77.150.20
CEN/TC 190

Magnesium and magnesium alloys - Magnesium alloy ingots and castings

SIST EN 1753:2019(Main)

EN 1753:2019

Standard
31 pages
English language
e-Library read for
AI-Chat
1 day

19-Sep-2018
06-Oct-2019
77.150.20
IFEK

ASTM B951-11(2018)(Practice)

Standard Practice for Codification of Unalloyed Magnesium and Magnesium-Alloys, Cast and Wrought

ABSTRACT
This practice provides a system for the codification of unalloyed magnesium and magnesium alloys in the cast and wrought forms. Code designations shall be based on their chemical composition limits. For alloys, designations shall consist of not more than two letters representing the alloying elements specified in the greatest amount, followed by the respective percentages and a serial letter. The letters that represent the alloying elements are: A for aluminum; C for copper; E for rare earths; J for strontium; K for zirconium; L for lithium; M for manganese; Q for silver; S for silicon; T for tin; V for gadolinium; W for yttrium; and Z for zinc. For unalloyed metals, designations shall consist of the specified minimum purity, followed by a serial letter. For both cases, the full name of the base metal precedes the designation, but is omitted for brevity when the base metal being referred to is obvious.
SCOPE
1.1 This practice provides a system for designating unalloyed magnesium and magnesium-alloys that have been used commercially since 1952, and thus is intended to be the registration source for unalloyed magnesium and magnesium-alloys. A record of designations along with the established compositions is given in Table 2.
1.2 The equivalent Unified Numbering System (UNS) alloy designations shown in the appendixes are in accordance with Practice E527.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard
7 pages
English language
sale 15% off

30-Apr-2018
77.150.20
B07

Founding - Technical conditions of delivery - Part 5: Additional requirements for magnesium alloy castings

EN 1559-5:2017(Main)

SIST EN 1559-5:2017

This part of EN 1559 specifies the additional technical delivery conditions for castings, see EN 1753 and cast anodes, see EN 12438 made from magnesium alloys.
This part of EN 1559 applies to magnesium alloy castings produced in sand or permanent moulds or by pressure die casting, centrifugal casting, continuous casting or investment casting.
This part of EN 1559 does not apply to ingots, bars, billets (or other shapes) for further reprocessing, such as re-melting or extrusion.

Standard
10 pages
English language
e-Library read for
AI-Chat
1 day

28-Feb-2017
29-Sep-2017
77.150.20
CEN/TC 190

Magnesium and magnesium alloys - Magnesium alloys for cast anodes

EN 12438:2017(Main)

SIST EN 12438:2017

This European Standard specifies the grades and the corresponding requirements for magnesium alloys for cast anodes.
This European Standard specifies 2 groups of cast magnesium alloy grades by a classification based on chemical composition. The first group deals with magnesium alloy ingots for anodes. The second group deals with magnesium alloy anode castings.
This European Standard specifies chemical composition, designation, testing and inspection documentation.
This European Standard does not cover technical delivery conditions for magnesium alloy anode castings (see EN 1559-1 [3] and EN 1559-5 [4]).

Standard
18 pages
English language
e-Library read for
AI-Chat
1 day

ASTM B91-17(Specification)

Standard Specification for Magnesium-Alloy Forgings

ABSTRACT
This specification covers UNS M11311, M11610, M11800, or M16600 magnesium alloy forgings. The conformance of each material to the required chemical composition can be determined using any suitable method of chemical analysis. Samples for chemical analysis should be taken when the ingots are poured or from the finished or semi-finished products by drilling, sawing, milling, turning, or clipping. The variations in testing speed do not seriously affect the obtained tensile property values. However, care must be exercised so that the testing speed does not exceed the ability of the equipment to function satisfactorily. Unless specified, forgings should be chrome pickled before shipment.
SCOPE
1.1 This specification covers magnesium alloy forgings designated as shown in Table 1. (A) Limits are in weight percent maximum unless shown as a range or stated otherwise.(B) These alloy designations were established in accordance with Practice B951.(C) Includes listed elements for which no specific limit is shown.
1.2 The values stated in inch-pound units are the standard. The SI values in parentheses are provided for information only.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Technical specification
5 pages
English language
sale 15% off
Technical specification
5 pages
English language
sale 15% off

30-Apr-2017
77.150.20
B07

ASTM B92/B92M-17(Specification)

Standard Specification for Unalloyed Magnesium Ingot and Stick For Remelting

ABSTRACT
This specification covers the standard for magnesium alloys in ingot and stick forms proposed for used in remelting. Magnesium 9980A alloys are available in ingot and stick form. Magnesium 9980B, 9990A, 9995A, and 9998A, on the other hand, are generally available in ingot form only. The specimens shall be produced with no slag and shall have a clean surface free from dirt, slag, or other foreign contaminants. Alloys shall adhere to specified chemical composition requirements. Any suitable chemical analysis method can be used unless otherwise prescribed.
SCOPE
1.1 This specification covers magnesium in the form of ingot and stick for remelting: 9980A is available in ingot and stick form, and 9980B, 9990A, 9995A, and 9998A are generally available only in ingot form.
1.2 The values stated in SI units are to be regarded as a separate standard. The values stated in each system are not exact equivalents, therefore each system must be used independently of the other.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Technical specification
3 pages
English language
sale 15% off
Technical specification
3 pages
English language
sale 15% off

30-Apr-2017
77.150.20
B07

ASTM B199-17(Specification)

Standard Specification for Magnesium-Alloy Permanent Mold Castings

ABSTRACT
This specification covers magnesium alloy permanent mold casting. The castings may be subjected to the heat treatment necessary to produce material that will conform to the requirements specified. Heat treatment shall be performed on the whole of a casting, never on a part only, and shall be applied in a manner that will produce the utmost uniformity. The castings shall be of uniform quality and condition, free of cracks or other injurious defects, and shall be well cleaned by sand blasting or any other approved process before inspection. The material shall conform to the chemical composition limits prescribed. Any suitable method of chemical analysis may be used. Unless otherwise specified, heat treatment for the applicable tempers designated shall be in accordance with practice B 661 or with Military Specification MIL-M-6857. The tension test specimens representing the castings shall conform to the requirements specified. At least one tension test specimen shall be cast from each melt of 2000 lb (907 kg) or fraction thereof to represent the castings poured from the same melt. The tension tests shall be made in accordance with test methods B 557.
SCOPE
1.1 This specification covers magnesium alloy permanent mold casting alloys designated as shown in Table 1.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are provided for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Technical specification
6 pages
English language
sale 15% off
Technical specification
6 pages
English language
sale 15% off

30-Apr-2017
77.150.20
B07

Magnesium and magnesium alloys - Magnesium alloy ingots and castings

ISO 16220:2017(Main)

SIST ISO 16220:2021

Standard
23 pages
English language
e-Library read for
AI-Chat
1 day
Standard
18 pages
English language
sale 15% off

SIST EN 1559-5:2017(Main)

Founding - Technical conditions of delivery - Part 5: Additional requirements for magnesium alloy castings

EN 1559-5:2017

Standard
10 pages
English language
e-Library read for
AI-Chat
1 day

29-Sep-2015
13-Mar-2017
77.150.20
IFEK

Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form

EN 755-9:2016(Main)

SIST EN 755-9:2016

This European Standard specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded profile with a cross section contained within a circumscribing circle not greater than 800 mm (see Figure 1).
The temper designations used in this part are according to EN 515.
This European Standard applies to extruded profiles for general engineering applications only.
(...)

Standard
20 pages
English language
e-Library read for
AI-Chat
1 day

07-Jun-2016
30-Dec-2016
77.120.10
77.150.10
77.150.20
CEN/TC 132

Magnesium and magnesium alloys - Designation system for anodes, ingots and castings - Material numbers and material symbols

SIST EN 1754:2015(Main)

EN 1754:2015

This European Standard specifies a material designation system for magnesium and magnesium alloys either by numbers or by symbols for castings including anodes and ingots intended for remelting.
The designation system by numbers is only applicable to standardized magnesium and magnesium alloys (see 2.1).
The designation system by symbols is applicable to
a)   standardized magnesium and magnesium alloys (see 2.1);
b)   non-standardized magnesium and magnesium alloys (see 2.2).
NOTE 1   The standardized designation by symbols does not necessarily imply that the material is standardized.
NOTE 2   Magnesium and magnesium alloys for aerospace applications referred to in European standards prepared by AECMA (fr: Association Européenne des Constructeurs de Matériel Aérospatial) have different designations.

Standard
12 pages
English language
e-Library read for
AI-Chat
1 day

28-Feb-2014
07-Sep-2015
77.150.20
IFEK

Magnesium and magnesium alloys - Designation system for anodes, ingots and castings - Material symbols and material numbers

EN 1754:2015(Main)

SIST EN 1754:2015

Standard
12 pages
English language
e-Library read for
AI-Chat
1 day

04-Aug-2015
77.150.20
CEN/TC 190

EN 1753:1997/AC:1997(Corrigendum)

Magnesium and magnesium alloys - Magnesium alloy ingots and castings

SIST EN 1753:1998/AC:2004

Corrigendum
5 pages
German language
e-Library read for
AI-Chat
1 day

12-Nov-1997
13-Apr-2025
77.150.20
CEN/TC 190

Founding - Technical conditions of delivery - Part 5: Additional requirements for magnesium alloy castings

EN 1559-5:1997(Main)

SIST EN 1559-5:2000

This part of EN 1559 applies to castings made from magnesium alloys produced by sand casting, permanent mould casting, pressure die casting, centrifugal casting, continuous casting or investment casting. This standard specifies the additional technical delivery conditions for magnesium alloy castings. This standard does not apply to ingots, bars, billets (or other shapes) for further reprocessing, such as remelting, grinding or extrusion.

Standard
7 pages
English language
e-Library read for
AI-Chat
1 day

21-Oct-1997
13-Apr-2025
77.150.20
CEN/TC 190

Magnesium and magnesium alloys - Magnesium and magnesium alloy anodes, ingots and castings - Designation system

EN 1754:1997(Main)

SIST EN 1754:1998

This European Standard specifies - a designation system for magnesium and magnesium alloys by numbers; - a designation system for magnesium and magnesium alloys by symbols. This standard applies to magnesium and magnesium alloys for ingots intended for remelting and to magnesium and magnesium alloys for castings, including anodes.

Standard
6 pages
English language
e-Library read for
AI-Chat
1 day

17-Jun-1997
13-Apr-2025
77.150.20
CEN/TC 190

Magnesium and magnesium alloys - Magnesium alloy ingots and castings

EN 1753:1997(Main)

SIST EN 1753:1998

This European Standard specifies the chemical composition of magnesium alloys for ingots. It also specifies the chemical composition of magnesium alloy castings. It also specifies the mechanical properties of separately cast samples of these alloys (see clause 6). By agreement, it also specifies the mechanical properties of magnesium alloys castings determined from samples cut from a casting.

Standard
14 pages
English language
e-Library read for
AI-Chat
1 day

17-Jun-1997
13-Apr-2025
77.150.20
CEN/TC 190

SIST EN 1753:1998/AC:2004(Amendment)

Magnesium and magnesium alloys - Magnesium alloy ingots and castings

EN 1753:1997/AC:1997

Corrigendum
5 pages
German language
e-Library read for
AI-Chat
1 day

31-Aug-2004
03-Oct-2019
77.150.20
IFEK

Magnesium and magnesium alloys - Magnesium alloy ingots and castings

SIST EN 1753:1998(Main)

EN 1753:1997

Standard
14 pages
English language
e-Library read for
AI-Chat
1 day

31-Jul-1998
03-Oct-2019
77.150.20
IFEK

SIST EN 1559-5:2000(Main)

Founding - Technical conditions of delivery - Part 5: Additional requirements for magnesium alloy castings

EN 1559-5:1997

Standard
7 pages
English language
e-Library read for
AI-Chat
1 day

31-Mar-2000
08-Mar-2017
77.150.20
IFEK

Magnesium and magnesium alloys - Magnesium and magnesium alloy anodes, ingots and castings - Designation system

SIST EN 1754:1998(Main)

EN 1754:1997

Standard
6 pages
English language
e-Library read for
AI-Chat
1 day

31-Jul-1998
02-Sep-2015
77.150.20
IFEK

ISO 16220:2005/Amd 1:2007(Amendment)

Magnesium and magnesium alloys - Magnesium alloy ingots and castings - Amendment 1: Additional alloys

Standard
5 pages
English language
sale 15% off

17-May-2007
17-May-2007
77.150.20
ISO/TC 79/SC 5

SIST ISO 16220:2002(Main)

Magnesium and magnesium alloys -- Magnesium alloy ingots and castings

ISO 16220:2000

Standard
12 pages
English language
e-Library read for
AI-Chat
1 day
Standard
12 pages
English language
sale 15% off
Standard
12 pages
French language
sale 15% off

31-Jan-2002
31-Aug-2005
77.150.20
INEK

Magnesium and magnesium alloys - Magnesium alloy ingots and castings

ISO 16220:2005(Main)

SIST ISO 16220:2005

ISO 16220:2005 specifies the chemical composition of magnesium alloy ingots. It also specifies the chemical composition of magnesium alloy castings and the mechanical properties of separately cast samples of these alloys. By agreement, ISO 16220:2005 also specifies the mechanical properties of magnesium alloy castings determined from samples cut from a casting.

Standard
12 pages
English language
e-Library read for
AI-Chat
1 day
Standard
12 pages
English language
sale 15% off
Standard
12 pages
French language
sale 15% off

13-Mar-2005
13-Mar-2005
77.150.20
ISO/TC 79/SC 5

ISO 16220:2000/Cor 1:2000(Corrigendum)

Magnesium and magnesium alloys - Magnesium alloy ingots and castings - Technical Corrigendum 1

Standard
3 pages
English language
sale 15% off
Standard
3 pages
French language
sale 15% off

22-Nov-2000
22-Nov-2000
77.150.20
ISO/TC 79/SC 5

Magnesium and magnesium alloys - Magnesium alloy ingots and castings

ISO 16220:2000(Main)

SIST ISO 16220:2002

Standard
12 pages
English language
e-Library read for
AI-Chat
1 day
Standard
12 pages
English language
sale 15% off
Standard
12 pages
French language
sale 15% off

07-Jun-2000
07-Jun-2000
77.150.20
ISO/TC 79/SC 5

Unalloyed magnesium ingots - Chemical composition

ISO 8287:1984(Main)

Standard
1 page
English language
sale 15% off
Standard
1 page
French language
sale 15% off

30-Sep-1984
30-Sep-1984
77.150.20
ISO/TC 79/SC 5

Magnesium alloys - Round bars and tubes - Dimensional tolerances

ISO 7773:1983(Main)

The products covered in this document may be manufactured from any wrought magnesium alloys, especially from magnesium-aluminium-zinc alloys and magnesium-zirconium-zinc alloys. Tables give tolerances on diameter, random and fixed lengths, and nominal wall thickness of tubes. Straightness is also specified.

Standard
3 pages
English language
sale 15% off
Standard
3 pages
French language
sale 15% off
Standard
3 pages
French language
sale 15% off

31-Jul-1983
31-Jul-1983
23.040.15
77.150.20
ISO/TC 79/SC 5

Castings in magnesium alloys containing zirconium - Chemical composition and mechanical properties

ISO 3115:1981(Main)

Standard
2 pages
English language
sale 15% off
Standard
2 pages
French language
sale 15% off

30-Jun-1981
30-Jun-1981
77.150.20
ISO/TC 79/SC 5

Extruded solid profiles in aluminium-zinc- magnesium alloy Al Zn4,5 Mg1 (7020) - Chemical composition and mechanical properties

ISO 3335:1977(Main)

Standard
2 pages
English language
sale 15% off
Standard
2 pages
French language
sale 15% off

Magnesium alloy sand castings - Reference test bar

ISO 2377:1972(Main)

The standard specifies the dimensions and method of production of reference test bars for magnesium alloy sand castings. A figure shows shape and dimensions of a mould pattern which allows the casting of a set of four reference test bars.

Standard
1 page
English language
sale 15% off
Standard
1 page
French language
sale 15% off
Standard
1 page
French language
sale 15% off

29-Feb-1972
29-Feb-1972
77.150.20
ISO/TC 79/SC 5