IEC 63356-1:2023 specifies data sheets of LED lamps and LED modules with a series of parameters per data sheet for a specific LED light source that enables interchangeability between products from different LED light source manufacturers. This second edition cancels and replaces the first edition published in 2022. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of datasheets for GH36d capped LED lamps; b) addition of datasheets for GJ6.6t and GJ6.6d-1 capped LED lamps; c) addition of datasheets for GR6d capped LED lamps.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day

NEW!IEC 62031:2018 is available as IEC 62031:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62031:2018 specifies general and safety requirements for light-emitting diode (LED) modules: - non-integrated LED modules (LEDni modules) and semi-integrated LED modules (LEDsi modules) for operation under constant voltage, constant current or constant power; - Integrated LED modules (LEDi modules) for use on DC supplies up to 250 V or AC supplies up to 1 000 V at 50 Hz or 60 Hz. This second edition cancels and replaces the first edition published in 2008, Amendment 1:2012 and Amendment 2:2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a. the scope was clarified as well as the wording in several other clauses; b. the normative references were updated; c. the definitions for "replaceable LED module", "non-replaceable LED module" and "non-user replaceable LED module" were introduced while other definitions covered by IEC 62504 have been removed; d. the marking clause was restructured and a table added to provide an informative overview; e. the marking requirements for built-in LED modules were changed; f. the entry for the marking with the working voltage was revised; g. the provisions for terminals and heat management were revised; h. Annex B was deleted; i. information for luminaire design with regard to working voltage and water contact was introduced; j. an abnormal temperature test was introduced.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 63013:2017 is applicable to LED packages for general lighting services. It specifies procedures and conditions for measuring the luminous flux maintenance of LED packages. It also provides the procedures and conditions (criteria) of projecting the long-term luminous flux maintenance based on limited luminous flux maintenance test data collected. Within the context of this document, wherever luminous flux measurement data is specified, radiant flux measurement data can also be used.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 63356 specifies design parameters and design values of a LED light source or related interface characteristics. Note 1: Interface characteristics can cover interfaces between LED light source and luminaire/controlgear or LED light source and additional attachments. Note 2: Interfaces can be related to for example electrical, mechanical, or optical aspects. This part does not cover interchangeability between products from different LED light source manufacturers. Note 3: Interchangeability is covered by Part 1. Lamp caps and lampholders specified in the IEC 60061 series are not in the scope of this document. Compliance criteria relating to parameters in this document are covered by IEC 63220 for safety, or IEC 63221 for performance.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 63356 specifies datasheets of LED lamps and LED modules with a series of parameters per datasheet for a specific LED light source that enables interchangeability between products from different LED light source manufacturers. Compliance criteria relating to datasheet parameters in this document are covered by IEC 63220 for safety, or IEC 63221 for performance.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 632186:2022 specifies the performance requirements of flexible organic light emitting diode tiles and panels for use on supplies up to 120 V ripple free DC for indoor and similar general lighting purposes and designed for being bent during the manufacturing process of curved luminaires.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2019-02-26 PC: BT approved the European elements, standard can be published
2019-01-22SW: Waiting for BT document to approve annex ZZ.
2019-01-18; GEM: EY quality review confirmation to consider as 'compliant'
2018-09-26: PEC: LVD assessment 'compliant', can be cited for LVD
2018-07-13 - GEM: [assessment received:2018-07-13] [ref:CLCTC34_61527_PUB_M511_20180601_AR]  [outcome:inconclusive] - CCMC/TC to advise how to adress this
2018-04-27: Annex zz recieved - waiting for consultant assessment - shall go to BT
2017-04-26 OD: Publication pending, missing annexZ and missing consultant assessment

  • Amendment
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 63146:2019 establishes requirements for specification sheets relating to light emitting diode (LED) packages designed for the emission of white light for general lighting applications. This document does not contain compliance criteria.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2019-10-24 PeC: to revisit after SLR is published

  • Amendment
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

No scope available

  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the performance requirements for metal halide lamps for general lighting purposes. For some of the requirements given in this document, reference is made to "the relevant lamp data sheet". For some lamps, these data sheets are contained in this document. For other lamps, falling under the scope of this document, the relevant data are supplied by the lamp manufacturer or responsible vendor. The requirements of this document relate only to type testing. The requirements and tolerances specified in this document correspond to testing of a type test sample submitted by the manufacturer for that purpose. In principle this type test sample consists of units having characteristics typical of the manufacturer’s production and being as close to the production centre point values as possible. It can be expected that with the tolerances given in this document, the product manufactured in accordance with the type test sample will comply with this document for the majority of production. Due to the production spread however, it is inevitable that there will sometimes be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes, see ISO 2859-10.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 62868 specifies the safety requirements for flexible organic light emitting diode tiles and panels for use on supplies up to 120 V ripple free DC for indoor and similar general lighting purposes and designed for being bent during the manufacturing process of curved luminaires.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62868-2-1:2020 specifies safety requirements for semi-integrated organic light emitting diode modules operating with an external controlgear connected to the mains voltage, and which, in addition, have a control means inside ("semi-integrated") for operation under constant voltage, constant current or constant power and have a rated voltage up to 120 V ripple free DC or 50 V AC RMS at 50 Hz or 60 Hz.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62868-1:2020 specifies general safety requirements of OLED products for use on DC supplies up to 1000 V or AC supplies up to 1000 V at 50 Hz or 60 Hz for indoors and similar general lighting purposes. This document applies to any OLED light sources which are not covered by IEC 62868-2 (all parts). This first edition cancels and replaces IEC 62868 published in 2014.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62868-2-2:2020 specifies the safety requirements for integrated organic light-emitting diode (OLED) modules for use on ripple free DC supplies up to 1000 V or AC supplies up to 1 000 V RMS at 50 Hz or 60Hz.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61167:2018 specifies the performance requirements for metal halide lamps for general lighting purposes. This fourth edition cancels and replaces the third edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition. a) A set of new lamp data sheets has been introduced for lamp types designed for replacing high pressure sodium lamps. b) A set of new lamp data sheets has been introduced for 4 200 K versions of 3 000 K lamp types already in the standard. c) A set of new lamp data sheets has been introduced for new lamp types where high frequency ignition data is important. d) Annex G has been revised to incorporate high frequency ignition. As a consequence of this change, all data sheets in the standard have been revised to a new format. e) A new informative Annex K has been introduced, giving recommended methods of making lamp temperature measurements.

  • Standard
    415 pages
    English language
    sale 10% off
    e-Library read for
    1 day

No scope available

  • Amendment
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document is applicable to electric light sources (see Note 1) for use in automotive applications, for example in road illumination devices and/or light signalling devices for road vehicles. It is especially applicable to light sources listed in UN Resolution R.E.5 and light sources subject to other legislations. This document specifies the technical requirements for interchangeability for example dimensional, electrical and photometrical characteristics, and includes test methods. For the light sources listed in this document, the data sheets are contained either in this document or are included by reference to UN Resolution R.E.5. Performance requirements are specified in IEC 60810, for example life, torsion strength, resistance to vibration and shock. The requirements for miniature light sources for supplementary purposes, not subject to legislation, are specified in IEC 60983. NOTE 1 The terms "lamp" and "light source" are both used in this document to mean the same product, so the two terms are interchangeable throughout this document. NOTE 2 In various vocabularies and standards, different terms are used for "incandescent lamp" (IEC 60050845:1987, 845-07-04), "discharge lamp" (IEC 60050-845:1987, 845-07-17) and "LED lamp". In this document "filament lamp", "discharge lamp" and "LED light source" are used, however, where only "lamp" or "light source" is written, all light sources, independent of the technology used, are meant, unless the context clearly shows that it applies to one kind of technology only. In the UN Regulations, the word "light source" is used for the products specified in this document. NOTE 3 Wherever the term "device" is used, it is meant to designate equipment which is used as a luminaire. It can for instance take the form and purpose of a headlight or signal light.

  • Standard
    97 pages
    English language
    sale 10% off
    e-Library read for
    1 day

NEW!IEC 60810:2017 is available as IEC 60810:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60810:2017 is applicable to filament lamps, discharge lamps, LED light sources and LED packages to be used in road vehicles, i.e. in headlamps, fog-lamps, signalling lamps and interior lighting. It is especially applicable to those lamps and light sources which are listed in IEC 60809. This fifth edition cancels and replaces the fourth edition published in 2014 and Amendment 1:2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - update and clarification of the title and scope; - introduction of new LED light sources; - introduction of requirements for LED light sources; - introduction of guidelines on LED package robustness validation for LED packages.

  • Standard
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61228:2020 is available as IEC 61228:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61228:2020 describes the method of measuring, evaluating and specifying the UV irradiation characteristics of fluorescent ultraviolet lamps that are used in appliances for tanning purposes. It includes specific requirements regarding the marking of such lamps. This third edition cancels and replaces the second edition published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - maintenance code: description of the depreciation of the UV irradiance lamp during operation; - operating position: information added for single capped lamps; - spectroradiometric measuring system: new information about distance between sensor and lamp axis; - measurement and evaluation procedure: separated detailed information for double capped fluorescent UV lamps and single capped fluorescent UV lamps; - Annex C (normative), Method of test for irradiance maintenance: new information added; - Annex D (normative), Reflector gauge: new information added; - Annex E (normative), Lamp datasheets for measurement: complementary information added.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard specifies sample preparation methods for determining mercury levels in new tubular fluorescent lamps (including single capped, double capped, self-ballasted and CCFL for backlighting) containing 0,1 mg mercury or more. The intended resolution of the methods described in this standard is of the order of 5 %. Mercury level measurement of spent lamps is excluded, as during lamp operation, mercury gradually diffuses into the glass wall and reacts with the glass materials. The test method of this standard does not recover mercury that is diffused into or reacted with or otherwise incorporated irreversibly with the glass wall of discharge tubes. This standard does not contain information on measurement. Measurement is specified in IEC 62321.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Incorporates Common Modifications PR=61095.

  • Amendment
    71 pages
    English language
    sale 10% off
    e-Library read for
    1 day

CMs required - WI=58957
Work started in CLC/SR 34A then transferred in the newly created CLC/TC 34A (D145/097)

  • Amendment
    107 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2017-06-08: Final decision is to publish A1 and A11 separately the same day. A1 is identical to IEC A1.
2017-05-31: D156/039: to be published
2017-05-04: Publication on the hold pending TC 34A reply about A11 (pr=58955)
2015-11-18 - CLC/TC 34A request that A1 is published together with the European Amendment A11 (WI 58955).

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62717:2014 specifies the performance requirements for LED modules, together with the test methods and conditions, required to show compliance with this standard. This first edition cancels and replaces IEC PAS 62717 published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC PAS 62717: - all terms and definitions are aligned with IEC 62504 and relevant documents of CIE. For example, general terms like "rated value" are shifted to IEC 62504. - a statement on the applicability on a population is included. - the normative references are completed and cleaned from standards that are not in use. - with regard to EMC, references to harmonic currents are given. - the change, which has an effect on most parts of the standard, is the split of failure mechanisms into abrupt failures and luminous flux depreciation. Consequently, new terms and definitions, new requirements for lumen maintenance and a complete new structure and contents of Annex C are introduced. - transition from tpmax to tprated is made, with the background that there is not one tpmax, but a choice of tp(rated) values, in combination with lifetime. - places where to mark (product, packaging, data sheets) are changed, and as a consequence of the split of failure mechanisms, new parameters are listed. Further, changes in the endurance test (ramping speed of temperature) are reflected in marking. - the concept of displacement factor instead of power factor is introduced. This led to new definitions, requirements and Annexes E and F. - the requirements on luminous efficacy are changed. - the requirements, associated with the family concept are reviewed. - statistics, based on confidence intervals are removed. This concerns requirements and limits for LED module power and luminous flux and deletion of Annex E. - new requirements for lumen maintenance are introduced. - as part of the endurance test, the maximum light decrease after accelerated operation life test is now fixed. - with regard to the discussion on type test and sample size, the number of pieces in a test sample is drastically reduced, see Table 7. - Annex A on measuring methods is completely restructured and reviewed, for example for ambient temperature and for shortening of stabilisation time when conducting subsequent light output measurements. - for electrical characteristics, the ageing time may be chosen as 500 h. - for photometric data file formats, reference is given to IEC 62722-1. - mistakes in the photometric code (Annex D) are corrected. - Annex G on optimised test duration is removed; instead, an INF sheet shall be published. - from the luminaire standard, a new Annex H on "Test equipment for temperature measurement" is taken over. - finally, the Bibliography is updated.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62922:2016 specifies the performance requirements of OLED tiles and panels for use on DC supplies up to 120 V or AC supplies up to 50 V at 50 Hz or 60 Hz for indoor and similar general lighting purposes.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The contents of the corrigendum of June 2015 have been included in this copy.

  • Amendment
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60968:2015 specifies the safety and interchangeability requirements, together with the test methods and conditions required to show compliance of tubular fluorescent lamps with integrated means for controlling starting and stable operation (self-ballasted fluorescent lamps). This third edition cancels and replaces the second edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition, where additions have been made to the following: a) caps and prevention of cap misuse; b) interchangeability; c) mechanical and electrical strength; d) creepage distances and clearances; e) end of lamp life precaution; f) abnormal operation; g) test conditions for dimmable and three-way lamps; h) water contact related marking; i) verification, and assessment; j) information for luminaire design in the form of annexes.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    13 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day

IEC 62776:2014 specifies the safety and interchangeability requirements, and the exchange operation together with the test methods and conditions required to show compliance of double-capped LED lamps with G5 and G13 caps, intended for replacing fluorescent lamps with the same caps, having: - a rated power up to 125 W; - a rated voltage up to 250 V.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62868:2014 specifies the safety requirements of OLED tiles and panels for use on d.c. supplies up to 120 V or a.c. supplies up to 50 V at 50 Hz or 60 Hz for indoor and similar general lighting purpose.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

PWI created for possible future // procedrues

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62035:2014 specifies the safety requirements for discharge lamps (excluding fluorescent lamps) for general lighting purposes. This International Standard is applicable to low-pressure sodium vapour lamps and to high-intensity discharge (HID) lamps, i.e. high-pressure mercury vapour lamps (including blended lamps), high-pressure sodium vapour lamps and metal halide lamps. It applies to single- and double-capped lamps, having caps as listed in Annex A. This standard only concerns safety criteria and does not take into account performance. The performance standards IEC 60188, IEC 60192, IEC 60662, IEC 61167 and IEC 61549 should be referred to for such characteristics. It may be expected that lamps which comply with this standard will operate safely at supply voltages between 90 % and 110 % of rated supply voltage and when operated with a ballast complying with IEC 61347-2-9 and IEC 60923, with a starting device complying with IEC 61347-2-1 and IEC 60927, and in a luminaire complying with IEC 60598-1. This second edition cancels and replaces the first edition published in 1999, AMD1:2003 and AMD2:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition. Photobiological safety requirements are taken care of on basis of the risk group concept of IEC 62471 and the technical report IEC TR 62778 on blue light hazard. This has consequences for terms, marking, structure of 4.6, and introduction of a new symbol "Caution, do not stare at light source". Special attention is given to blue light hazard.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day

DOP = DAV + 6 months (D139/C142)

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62931:2017 This document specifies the safety and interchangeability requirements together with the test methods and conditions required to show compliance of non-integrated tubular LED lamps, intended for general lighting purposes, having:  
a rated wattage up to 70 W,
a rated voltage up to 190 V ripple free DC,
GX16t-5 cap as listed in Table 1.  The requirements of this document relate only to type testing.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2021-04-13 FM: BT approved request to permanently remove link to LVD
2017-05-02: D156/C084 - Ratified standards not being made available.
Published following BT156/DG10475/DV

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62707-1:2013 specifies general requirements, a grid and a corresponding code for the colour binning of white LED packages emitting incoherent, visible radiation. It applies for LED packages. Other parts of the IEC 62707 series covering chromaticity of coloured LED packages, luminous flux/luminous intensity, colour rendering and forward voltage are in preparation or under consideration. This first edition cancels and replaces IEC/PAS 62707-1, published in 2011.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2013-07-05: Publication allocated to svandriessche@cencenelec.eu

  • Amendment
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62612:2013 specifies the performance requirements, together with the test methods and conditions, required to show compliance of LED lamps with integral means for stable operation, intended for domestic and similar general lighting purposes, having: - a rated power up to 60 W; - a rated voltage of > 50 V a.c. up to 250 V a.c.; - a lamp cap as listed in IEC 62560. This first edition of IEC 62612 cancels and replaces IEC/PAS 62612. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC/PAS 62612. a) The standard explicitly states that real life time tests are not part of the test regime. Instead, a period of up to 6 000 h is chosen in order to assess manufacturers' claims of maintenance. b) Technical features have been adapted to IEC/PAS 62717 (performance of LED modules) as far as possible. Examples are the family approach and the temperature measuring point. c) Marking requirements are shifted from the product to the packaging. d) The number of lamps to be tested is made test specific, not general. e) First requirements are given for setting the colour for colour adjustable lamps and the luminous flux level of dimmable lamps. f) The structure of tests is clearly divided between requirement and compliance. g) Statistical compliance is separated into individual and average. h) Light output requirements are extended to luminous intensity distribution, peak intensity, beam angle and efficacy. i) The use of the terms 'correlated colour temperature' and 'chromaticity coordinates' is corrected. j) The number of tolerance categories is reduced from 8 to 4, and split between initial and maintained values. k) Colour rendering is differently assessed at initial and maintained state. l) Three lumen maintenance categories are given instead of five. m) The endurance tests are completely re-established. n) The verification (formerly: assessment) clause is completed. o) Information for luminaire design is added. p) Stabilisation is more precise (Annex A on the method of measuring lamp characteristics) and extension is made for the additional photometric and colorimetric parameters. q) Annex B on measuring luminous flux is contained in Annex A. New Annex B provides the photometric code. r) Further annexes are added: Annex C and D for displacement factor, Annex E for life time metrics/reliability and Annex F for examples of LED dies and LED packages.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62838:2015 specifies the safety and interchangeability requirements, together with the test methods and conditions, required to show compliance of LED lamps with integrated means for stable operation, intended for domestic and similar general lighting purposes.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard specifies the safety requirements for double-capped fluorescent lamps for general lighting purposes of all groups having Fa6, Fa8, G5, G13, 2G13, R17d and W4.38.5d caps. It also specifies the method a manufacturer should use to show compliance with the requirements of this standard on the basis of whole production appraisal in association with his test records on finished products. This method can also be applied for certification purposes. Details of a batch test procedure which can be used to make limited assessment of batches are also given in this standard.
NOTE – Compliance with this standard concerns only safety criteria and does not take into account the performance of double-capped fluorescent lamps for general lighting purposes with respect to luminous flux, colour,
starting and operational characteristics. Readers are referred to IEC 60081 for such characteristics.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard specifies the safety requirements for single-capped fluorescent lamps for general lighting purposes of all groups having caps according to Table 1.
It also specifies the method a manufacturer should use to show compliance with the requirements of this standard on the basis of whole production appraisal in association with his test records on finished products. This method can also be applied for certification purposes. Details of a batch test procedure which can be used to make limited assessment of batches are also given in this standard.
NOTE Compliance with this standard concerns only safety criteria and does not take into account the performance of single-capped fluorescent lamps for general lighting purposes with respect to luminous flux, colour, starting and operational characteristics. For this information, readers are referred to IEC 60901.
It may be expected that lamps which comply with this standard will operate safely at supply voltages between 90 % and 110 % of rated supply voltage of the used ballast and when operated with a ballast complying with IEC 61347-2-3 or IEC 61347-2-8 with a starting device complying with IEC 60155 (if applicable) and in a luminaire complying with IEC 60598-1.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard specifies lamps, or information relevant to lamps, not given elsewhere in existing IEC lamp standards. It covers both safety and performance aspects.

  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day