ECISS/TC 29/SC 1 - Tubes for pressure purposes
Standardization of technical delivery conditions for steel tubes for pressure purposes.
Tubes for pressure purposes
Standardization of technical delivery conditions for steel tubes for pressure purposes.
General Information
This document specifies technical delivery conditions for two test categories of submerged arc longitudinally (SAWL) or helically (SAWH) welded tubes of circular cross section, with specified elevated temperature properties, made from non-alloy quality steel or alloy special steel.
NOTE 1 These tube grades are intended to support the essential requirements of EU Directive 2014/68/EU in respect of pressure equipment covered under all relevant Categories as set out in Article 13 of that Directive.
NOTE 2 Once this standard is published in the Official Journal of the European Union (OJEU), presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to the technical data for the materials in this standard and does not presume adequacy of the material for a specific item of pressure equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for two test categories of electric welded tubes of circular cross section, with specified elevated temperature properties, made from non-alloy quality steel or alloy special steel.
NOTE 1 These tube grades are intended to support the essential requirements of EU Directive 2014/68/EU in respect of pressure equipment with specified elevated temperature properties, covered under all relevant Categories as set out in Article 13 of that Directive.
NOTE 2 Once this standard is published in the Official Journal of the European Union (OJEU), presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to the technical data for the materials in this standard and does not presume adequacy of the material for a specific item of pressure equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of a specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account any subsequent processing procedures which may affect properties of the base materials.
- Standard34 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for two test categories of electric welded tubes of circular cross section, with specified low temperature properties, made from non-alloy quality steel.
NOTE 1 These tube grades are intended to support the essential requirements of EU Directive 2014/68/EU in respect of pressure equipment with specified low temperature properties covered under all relevant Categories as set out in Article 13 of that Directive.
NOTE 2 Once this standard is published in the Official Journal of the European Union (OJEU), presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to the technical data for the materials in this standard and does not presume adequacy of the material for a specific item of pressure equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
- Standard35 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for qualities TR1 and TR2 of electric welded and submerged arc welded tubes of circular cross section, with specified room temperature properties, made from non-alloy quality steel.
NOTE 1 Quality TR2 is intended to support the essential requirements of EU Directive 2014/68/EU in respect of pressure equipment with specified room temperature properties (see Table 5).
NOTE 2 Once this standard is published in the Official Journal of the European Union (OJEU), presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to the technical data for the materials in this standard and does not presume adequacy of the material for a specific item of pressure equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of a specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account any subsequent processing procedures which may affect properties of the base materials.
- Standard46 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for two test categories of electric welded and submerged arc longitudinally (SAWL) or helically (SAWH) welded tubes of circular cross section, made from weldable fine grain steel.
NOTE 1 These tube grades are intended to support the essential requirements of EU Directive 2014/68/EU in respect of pressure equipment covered under all relevant Categories as set out in Article 13 of that Directive.
NOTE 2 Once this standard is published in the Official Journal of the European Union (OJEU), presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to the technical data for the materials in this standard and does not presume adequacy of the material for a specific item of pressure equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of a specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account any subsequent processing procedures which may affect properties of the base materials.
- Standard53 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for two test categories of submerged arc longitudinally (SAWL) or helically (SAWH) welded tubes of circular cross section, with specified low temperature properties, made from non-alloy quality steel.
NOTE 1 These tube grades are intended to support the essential requirements of EU Directive 2014/68/EU in respect of pressure equipment with specified low temperature properties (see Table 5), covered under all relevant Categories as set out in Article 13 of that Directive.
NOTE 2 Once this standard is published in the Official Journal of the European Union (OJEU), presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to the technical data for the materials in this standard and does not presume adequacy of the material for a specific item of pressure equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
- Standard38 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the technical delivery conditions for two qualities TR1 and TR2 of seamless tubes of circular cross section with specified room temperature properties made of non-alloy quality steel.
NOTE Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, with specified low temperature properties, made of non-alloy and alloy steel.
NOTE Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, made of weldable alloyed fine grained steel.
NOTE Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
- Standard36 pagesEnglish languagesale 10% offe-Library read for1 day
Inclusion of new steel grades not considered during the preparation of the EN issued on 2002
- Draft22 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10217 specifies the technical delivery conditions in two test categories for welded tubes of circular cross-section made of austenitic and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
NOTE Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, pressure equipment directive, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
- Standard36 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section made of austenitic (including creep resisting steel) and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
NOTE Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
- Standard46 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel.
This Part of EN 10216 may also be applied for tubes of non-circular cross section; necessary modification should be agreed at the time of enquiry and order.
NOTE Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
- Standard45 pagesEnglish languagesale 10% offe-Library read for1 day
Modify the clause 9 Inspection and the Annex ZA in order to make them in line with the provision of Directive 97/23/EC (PED).
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
Modify the clause 9 Inspection and the Annex ZA in order to make them in line with the provision of Directive 97/23/EC (PED).
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
Modify the clause 9 Inspection and the Annex ZA in order to make them in line with the provision of Directive 97/23/EC (PED).
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
Modify the clause 9 Inspection and the Annex ZA in order to make them in line with the provision of Directive 97/23/EC (PED).
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
Modify the clause 9 Inspection and the Annex ZA in order to make them in line with the provision of Directive 97/23/EC (PED).
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
Modify the clause 9 Inspection and the Annex ZA in order to make them in line with the provision of Directive 97/23/EC (PED).
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10217 specifies the technical delivery conditions in two test categories of submerged arc welded tubes of circular cross section, with specified low temperature properties, made of non-alloy steel.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10217 specifies the technical delivery conditions in two test categories of submerged arc welded tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel.
- Standard35 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10217 specifies the technical delivery conditions in two test categories of electric welded tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel.
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10217 specifies the technical delivery conditions in two test categories of electric welded tubes of circular cross section, with specified low temperature properties, made of non-alloy steel.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10217 specifies the technical delivery condition in two test categories for welded tubes of circular cross section, made of weldable alloy fine grain steel.
- Standard45 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10217 specifies the technical delivery conditions for two qualities TR1 and TR2 of welded tubes of circular cross section, made of non-alloy quality steel and with specified room temperature properties.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10217 specifies the technical delivery conditions in two test categories for welded tubes of circular cross-section made of austenitic and austenitic-ferritic stainless steel which are applied for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
- Standard37 pagesEnglish languagesale 10% offe-Library read for1 day
TC - Modifications to steel number 1.4571 in Table 9
DIN - Translation improvements to steel grade 1.4941 in Table 3, to steelgrade 1.4501 in Table 4, 8.5.2.1, Table 15, 11.3.3, 11.3.4 and steel grade 1.4940 in Table A.1
2013: Originator of XML version: first setup pilot of CCMC in 2012
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10216 specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel.
NOTE This Part of EN 10216 may also be applied for tubes of non-circular cross section; necessary modification should be agreed at the time of enquiry and order.
- Standard45 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section made of austenitic (including creep resisting steel) and austenitic-ferritic stainless steel which are applied for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
- Standard45 pagesEnglish languagesale 10% offe-Library read for1 day
Modify the clause 9 Inspection and the Annex ZA in order to make them in line with the provision of Directive 97/23/EC (PED).
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
Modify the clause 9 Inspection and the Annex ZA in order to make them in line with the provision of Directive 97/23/EC (PED).
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
Modify the clause 9 Inspection and the Annex ZA in order to make them in line with the provision of Directive 97/23/EC (PED).
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10216 specifies the technical delivery conditions in two categories for seamless tubes of circular cross section, made of weldable alloyed fine grained steel.
- Standard34 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10216 specifies the technical delivery conditions for two qualities TR1 and TR2 of seamless tubes of circular cross section with specified room temperature properties made of non-alloy quality steel.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10216 specifies the technical delivery conditions in two categories for seamless tubes of circular cross section, with specified low temperature properties, made of non-alloy and alloy steel.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
Modify the clause 9 Inspection and the Annex ZA in order to make them in line with the provision of Directive 97/23/EC (PED).
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10216 specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel.
NOTE This Part of EN 10216 may also be applied for tubes of non-circular cross section; necessary modification should be agreed at the time of enquiry and order.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day