ECISS/TC 28 - Steel forgings

TC - Table 4, 3rd column, addition of "d"

TC - Table 4, 3rd column, addition of "d"

This European Standard specifies the tolerances on dimensions, shape and mass for semi-finished products intended to undergo hot forming by forging, i.e. blooms, slabs and billets made of:
- general purpose steels, in accordance with EN 10250-1 to 4;
- steels for pressure purposes, in accordance with EN 10222-1 to 5.
It does not cover semi-finished products intended for drop forging which are covered by EN 10243-1.

1.1 This European Standard specifies the dimensional tolerances for steel drop and vertical press forgings made under hammers and presses. The first part of this European Standard applies to hot forgings in the delivery condition, made in carbon and alloy steels. The tolerances specified apply to forgings not exceeding 250 kg in mass or 2 500 mm maximum dimension. Tolerances for heavier or larger forgings shall be agreed at the time of enquiry and order.

This European Standard specifies the general delivery conditions for steel closed die forgings. These forgings are produced by blow or pressure of the heated product at a suitable temperature (hot or warm) in a die, which in the forming process shapes the material to the form of the die. Similar products such as warm extrusions and upset forgings, are also regarded as part of the process.

1.1 This European Standard specifies the dimensional tolerances for steel upset forgings made on horizontal forging machines. The second part of this European Standard applies to hot upset forgings, in the delivery condition, made in carbon and alloy steels. The tolerances specified apply to forgings not exceeding 250 kg in mass or 2 500 mm maximum dimension. Tolerances for heavier or layer forgings are subjected to negociation.

This Part of this European Standard specifies the technical delivery requirements for open die forgings, forged bars and products pre-forged and finished in ring rolling mills, manufactured from non-alloy quality and special steels and supplied in the normalized, normalized and tempered, quenched and tempered or annealed condition.

This part of this European Standard specifies the technical delivery requirements for open die forgings, forged bars and products pre-forged and finished in ring rolling mills, manufactured from alloy special steel and supplied in the quenched and tempered condition. Note: The majority of steels listed in this Part of EN 10250 are identical to steels specified in EN 10083-1 and more extensive information on hardenability and technological properties is given in that European Standard.

This part of this European Standard specifies the general technical delivery conditions for open die forgings, forged bars, and products pre-forged and finished in ring rolling mills, for general engineering purposes. General information on technical delivery conditions is given in EN 10021.

This Part of this European Standard specifies the technical delivery requirements for open die forgings, forged bars and products pre-forged and finished in ring rolling mills, manufactured from stainless steels with ferritic, martensitic, austenitic and austenitic-ferritic structures. Note: The majority of steels listed in this Part of EN 10250 are identical to steels specified EN 10088-3 and more extensive information on properties is given in that European Standard. General information on technical delivery conditions is given in EN 10021.

Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months (TC Res C 1/2000) (CC/000331)
2013: Originator of XML version: first setup pilot of CCMC in 2012

This Part of this European Standard specifies the technical delivery conditions for forgings for pressure purposes made of stainless steels, including creep resisting steels. Chemical composition and mechanical properties are specified. General information on technical delivery conditions is given in EN 10021.

This Part of this European Standard specifies the technical delivery conditions for forgings and for pressure purposes, made of ferritic and martensitic steels with specified elevated temperature properties. Chemical composition and mechanical properties are specified. General information on technical delivery conditions is given in EN 10021.

This Part of this European Standard specifies the technical delivery conditions of the types of forgings for pressure purposes made of weldable fine grain steels with high proof strength.  General information on technical delivery conditions is given in EN 10021.

This Part of this European Standard specifies the technical delivery conditions of forgings for pressure purposes, made of nickel steels, for use at low temperatures.   General information on technical delivery conditions is given in EN 10021.

This Part of this European Standard specifies the general technical delivery conditions for open die steel forgings, ring rolled products and forged bars for pressure purposes.   General information on technical delivery conditions is given in EN 10021.

This Part of EN 10228 specifies methods for the manual, pulse-echo, ultrasonic testing of forgings manufactured from austenitic and austenitic-ferritic stainless steels. Mechanised scanning techniques, such as immersion testing, may be used but should be agreed between the purchaser and supplier.

This Part of EN 10228 describes the method and acceptance criteria to be used for the magnetic particle inspection of forgings manufactured from ferromagnetic materials. The method described is used for the detection of surface discontinuities. It can also detect discontinuities just below the surface but sensitivity to such discontinuities diminishes rapidly with depth.

This part of EN 10228 describes the method and acceptance criteria to be used for the penetrant testing of steel forgings. The method described is used for the detection of surface discontinuities.

This part of EN 10228 describes the techniques to be used for the manual, pulse-echo, ultrasonic testing of forgings manufactured from ferritic and martensitic steel. Mechanised scanning techniques such as immersion testing may be used but should be agreed between the purchaser and supplier. This part of EN 10228 applies to four types of forgings, classified according to their shape and method of production. Types 1, 2 and 3 are essentially simple shapes. Type 4 covers complex shapes.

CMC - Special parapraph to be included in foreword as required by ECISS Internal Regulations, requested to JS/DL before publication but overlooked
2013: Originator of XML version: first setup pilot of CCMC in 2012

CMC - Special parapraph to be included in foreword as required by ECISS Internal Regulations, requested to JS/DL before publication but overlooked
2013: Originator of XML version: first setup pilot of CCMC in 2012