CEN/TC 226/WG 2 - Horizontal road signs
I.‐ In the field of the standardization activities: a. Other colors than white and yellow, used as permanent road markings (blue, green, etc.). b. Night‐time color, especially for yellow road markings, as a new essential characteristic of the road markings applied. II.‐ Intending to produce CEN/Technical Reports: a. Test methods and requirements for (positive and negative) noise produced by "structured road markings". b. Conditions for removing/masking/covering road markings. III.‐ In the field of Research and Development: a. Updating COST 331, with especial focus on geometry. After the consultation carrying on by the convenor of WG2, this project does not seem too feasible. If still relevant, we should try to explore other ways for funding. b. The use of the road markings as a "Low Cost - High Effective Road Safety Engineering Measure for the Treatment of Black Spots".
Horizontal road signs
I.‐ In the field of the standardization activities: a. Other colors than white and yellow, used as permanent road markings (blue, green, etc.). b. Night‐time color, especially for yellow road markings, as a new essential characteristic of the road markings applied. II.‐ Intending to produce CEN/Technical Reports: a. Test methods and requirements for (positive and negative) noise produced by "structured road markings". b. Conditions for removing/masking/covering road markings. III.‐ In the field of Research and Development: a. Updating COST 331, with especial focus on geometry. After the consultation carrying on by the convenor of WG2, this project does not seem too feasible. If still relevant, we should try to explore other ways for funding. b. The use of the road markings as a "Low Cost - High Effective Road Safety Engineering Measure for the Treatment of Black Spots".
General Information
This document outlines a method to measure the typical external noise emission produced when tyres of passenger car roll over a structured road marking. The result is a measure for the noise perceived in the surroundings of the road, hence not for interior noise in the car.
This method can be used for three purposes:
- determination of initial acoustic properties of a road marking, yielding a noise label for a given system;
- testing of the acoustic conformity of a particular marking to the noise label determined during the determination of initial acoustic properties;
- monitoring of the acoustic properties in the course of its lifetime.
The test result allows the road owner to make an assessment of the risk of nuisance when s/he considers a particular road marking system for application on a road in a noise sensitive area, e.g. built up areas. The method is also applicable to measurements on milled rumble strips.
- Technical specification12 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the product characteristics, laboratory test methods, the way of expressing results and the relevant procedures for assessment and verification of the constancy of performance for retroreflecting road studs, non depressible and depressible by design (designated as Type A and B, respectively) and which reflectors are made of glass, plastic or plastic with abrasion resistance layer (designated as Type 1, 2 and 3, respectively), to be used for permanent road markings, and delineation purposes, in circulation areas.
This document covers retroreflecting road studs (types - 1, 2, 3 - A, B) of white, yellow, amber, red and green colour of their reflectors.
This document does not cover:
- non-retroreflective road studs;
- temporary retroreflective road studs.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document describes the test method for carrying out road trials on retroreflecting road studs. Specifications are given for test sites, for the organization of the tests, and for the presentation of the results in the form of a test report.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for conducting road trials for road marking intended for use in both permanent and temporary road marking. Details are given for test sites, for the application of road marking materials on the test sites, for the parameters to be measured and the frequency of the measurements and for the presentation of the results in the form of a test report.
- Standard35 pagesEnglish languagesale 10% offe-Library read for1 day
This document covers testing of physical properties of road marking materials by laboratory methods.
The products covered and specified by this document are white and yellow paint, thermoplastic and cold plastic materials, with or without premix glass beads, to be used for permanent and/or temporary road markings on highways and other areas used by vehicular traffic. Other products and colours intended for road markings are not covered in this document.
Not all physical properties listed in this document have to be specified.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the performance for road users of white and yellow road markings, as expressed by their reflection in daylight or under road lighting, retroreflection in vehicle headlamp illumination, colour and skid resistance. Furthermore, the standard specifies test methods and conditions.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides guidance for removal or/and masking existing road markings. It includes methods of removal and criteria for selecting the removal method, as well as the requirements for the masking materials and the performance requirements of the resulting surface.
It does not apply to removable temporary road markings, which shall be removed in accordance to the manufacturer instructions.
Some recommendations are given for removing and masking road studs, removing wet paints, removing curing membranes in new cement concrete pavements and cleaning existing road markings.
- Technical report25 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies construction products which are white and yellow, removable or non-removable, preformed road marking materials, under the form of tape, cold plastic, thermoplastics with or without drop-on materials, to be used for permanent and/or temporary road markings in circulation areas. Other products and colours intended for road markings are not covered in this European Standard.
This European Standard also gives specifications for the evaluation of conformity for white and yellow, removable or non-removable, preformed road materials under the form of tape, cold plastic, thermoplastics with or without drop-on materials to be used for permanent and/or temporary road markings in circulation areas including type testing and factory production control.
This European Standard includes an Annex ZA for tapes, preformed cold plastic road marking and thermoplastic road marking with and without drop-on materials with the clauses addressing the provisions of the EU Construction Product Directive for permanent road marking.
- Standard37 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for wear simulator test for road marking materials intended for use in both permanent and temporary road markings including those with increased retroreflection under wet and rain conditions, without road studs.
It gives description for the equipment and for test plate’s characteristics; it also gives description for the test method involving road marking materials application, test conditions during wear test, parameters to be measured, frequency of the measurements and expression of the results as a test report.
This document gives also the requirements to be followed when the test is to be used for CE marking purposes.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
CEN/TC 226 - Modifications to 4.1.3, 4.2.2 and 4.3.3.
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements applicable to glass beads, anti-skid aggregates, and the mixture of the two, which are applied as drop-on materials on road markings products (i.e. paints, cold plastics and thermoplastics).
Glass beads and/or anti-skid aggregates, or their mixture, applied during the process of manufacturing other road marking products are not covered by this European Standard.
- Standard70 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies laboratory methods for the identification of road marking materials used in horizontal signalization. It is not necessary, unless required, to perform all of the tests described.
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
This document gives the requirements for factory production control (FPC) for the manufacturer of road marking materials
This document specifies which types of test have to be taken into consideration within the FPC but it leaves the precise methods to be applied to be dependent on the characteristics of the manufacturer’s installation and production methods. The precise parameters and methods will be found in the written procedures agreed between the manufacturer and the third party responsible for the initial assessment of the FPC.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies methods to obtain representative samples of road marking materials for testing and gives the appropriate test methods. The methods to obtain representative samples are described as appropriate for the main product types, i.e. paint, cold plastics, thermoplastics, premix glass beads, drop-on materials, preformed road markings and retroreflecting road studs.
NOTE This document may apply to the verification and/or identification of consignments of road marking materials or materials held in stock, for example in a warehouse or at the manufacturer's storage facility, or for materials which require checking prior to application.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
This European standard specifies the requirements for laboratory tests (Product control) and qualification procedures for the following material used in road marking materials. The requirements taken into consideration in this standard are: - granulometry; -refractive index of the glass; - chemical resis- tance; - quality; - surface treatments. This standard does not cover the glass beads used as a filler in the marking products.
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
This European standard specifies the requirements for laboratory tests (Product control) and qualification procedures for the following material used in road marking materials. The requirements taken into consideration in this standard are: - granulometry; -refractive index of the glass; - chemical resis- tance; - quality; - surface treatments. This standard does not cover the glass beads used as a filler in the marking products.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies white, yellow and orange road markings, removable or non-removable, under the form of road marking assemblies or preformed road markings, to be used for temporary road markings in circulation areas. Other road marking products and colours intended for temporary road markings are not covered in this document.
This document also gives specifications for the evaluation of conformity of temporary road markings in circulation areas including type testing and factory production control.
- Draft18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the product characteristics, laboratory test methods, the way of expressing results and the relevant procedures for assessment and verification of the constancy of performance, for preformed road markings (namely, marking tapes and preformed markings) of types I and II (structured and non-structured) to be used for permanent road markings, in circulation areas.
This document does not cover:
- hot applied thermoplastics, even if commercialized in the form of sheets or on rolls, which requires the addition of drop-on materials to build up the road marking on the field site. Those products are considered to be duly covered by EN 1871:2020;
- preformed road markings for temporary use.
- Draft41 pagesEnglish languagesale 10% offe-Library read for1 day
This standard specifies the initial performance requirements and laboratory test methods for solar powered, hardwired and communicating active road studs intended for use as permanent and temporary road marking materials.
- Draft23 pagesEnglish languagesale 10% offe-Library read for1 day
The construction products covered and specified by this European Standard are white and yellow paint, thermoplastic and cold plastic materials, with or without premix glass beads, to be used for permanent and/or temporary road markings in circulation areas. Other products and colours intended for road markings are not covered in this European Standard.
This European Standard gives also specifications for the evaluation of conformity for white and yellow paint, thermoplastic and cold plastic materials to be used for permanent and/or temporary road markings in circulation areas including type testing and factory production control.
This European Standard also includes an Annex ZA with the clauses addressing the provisions of the EU Construction Product Directive, for permanent road markings.
- Draft64 pagesEnglish languagesale 10% offe-Library read for1 day
The construction products covered and specified by this European Standard are white and yellow paint, cold plastic and thermoplastic materials, with or without premix glass beads, to be used for permanent and/or temporary road markings in circulation areas. Other products and colours intended for road markings are not covered in this European Standard.
This European Standard gives also specifications for the evaluation of conformity for white and yellow paint, cold plastic and thermoplastic materials to be used for permanent and/or temporary road markings in circulation areas including type testing and factory production control.
This European Standard also includes an Annex ZA with the clauses addressing the provisions of the EU Construction Product Directive, for permanent road markings.
- Draft67 pagesEnglish languagesale 10% offe-Library read for1 day
The construction products covered and specified on this European Standard are white and yellow, removable or non-removable, preformed road marking materials, under the form of tape, cold plastic, thermoplastics with or without drop-on materials, to be used for permanent and/or temporary road markings in circulation areas. Other products and colours intended for road markings are not covered in this European Standard
This document gives also specifications for the evaluation of conformity for white and yellow, removable or non-removable, preformed road materials under the form of tape, cold plastic, thermoplastics with or without drop-on materials to be used for permanent and/or temporary road markings in circulation areas including type testing and factory production control.
This European Standard also includes an Annex ZA for tapes, preformed cold plastic road marking and thermoplastic road marking without drop-on materials with the clauses addressing the provisions of the EU Construction Product Directive for permanent road marking.
For preformed Thermoplastic road marking with drop-on materials, Annex ZA of FprEN 1871:2011 applies.
- Draft27 pagesEnglish languagesale 10% offe-Library read for1 day
This document gives the requirements for factory production control (FPC) for the manufacturer of road marking materials
This document specifies which types of test have to be taken into consideration within the FPC but it leaves the precise methods to be applied to be dependent on the characteristics of the manufacturer’s installation and production methods. The precise parameters and methods will be found in the written procedures agreed between the manufacturer and the third party responsible for the initial assessment of the FPC.
- Draft14 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for wear simulator test for road marking materials intended for use in both permanent and temporary road markings including those with increased retroreflection under wet and rain conditions, without road studs.
It gives description for the equipment and for test plate’s characteristics; it also gives description for the test method involving road marking materials application, test conditions during wear test, parameters to be measured, frequency of the measurements and expression of the results as a test report.
This document gives also the requirements to be followed when the test is to be used for CE marking purposes.
- Draft21 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies methods to obtain representative samples of road marking materials for testing and gives the appropriate test methods. The methods to obtain representative samples are described as appropriate for the main product types, i.e. paint, cold plastics, thermoplastics, premix glass beads, drop-on materials, preformed road markings and retroreflecting road studs.
NOTE This document may apply to the verification and/or identification of consignments of road marking materials or materials held in stock, for example in a warehouse or at the manufacturer's storage facility, or for materials which require checking prior to application.
- Draft10 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the laboratory requirements and test methods for retroreflective and other road marking materials, both permanent and temporary.
- Draft57 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard gives guidance for conducting road trials for road marking materials intended for use in both permanent and temporary road marking. Recommendations are given for test sites, for the application of road marking materials on the test sites, for the parameters to be measured and the frequency of the measurements and for the presentation of the results in the form of a test report.
- Draft30 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for laboratory tests (production control) and qualification procedures for the following drop on materials used in road markings.
These materials are dropped on to paints, thermoplastics, cold plastics and any other marking product applied in a liquid state, immediately after application to the road surface.
The requirements taken into consideration in this standard are :
- glass beads : granulometry, refractive index of the glass, chemical resistance, quality, surface treatments ;
- antiskid aggregates : granulometry, chemical characteristics, friability, colour ;
- mixtures of glass beads and antiskid aggregates; and the requirements for both components.
- Draft49 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies laboratory methods for the identification of road marking materials used in horizontal signalization. It is not necessary, unless required, to perform all of the tests described.
- Draft30 pagesEnglish languagesale 10% offe-Library read for1 day
The construction products covered and specified on this European Standard are white and yellow, removable or non-removable, preformed road marking materials, under the form of tape, cold plastic, thermoplastics with or without drop-on materials, to be used for permanent and/or temporary road markings in circulation areas. Other products and colours intended for road markings are not covered in this European Standard
This document gives also specifications for the evaluation of conformity for white and yellow, removable or non-removable, preformed road materials under the form of tape, cold plastic, thermoplastics with or without drop-on materials to be used for permanent and/or temporary road markings in circulation areas including type testing and factory production control.
This European Standard also includes an Annex ZA for tapes, preformed cold plastic road marking and thermoplastic road marking without drop-on materials with the clauses addressing the provisions of the EU Construction Product Directive for permanent road marking.
For preformed Thermoplastic road marking with drop-on materials, Annex ZA of FprEN 1871:2011 applies.
- Draft39 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for wear simulator test for road marking materials intended for use in both permanent and temporary road markings including those with increased retroreflection under wet and rain conditions, without road studs.
It gives description for the equipment and for test plate’s characteristics; it also gives description for the test method involving road marking materials application, test conditions during wear test, parameters to be measured, frequency of the measurements and expression of the results as a test report.
This document gives also the requirements to be followed when the test is to be used for CE marking purposes.
- Draft6 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies laboratory methods for the identification of road marking materials used in horizontal signalization. It is not necessary, unless required, to perform all of the tests described.
- Draft32 pagesEnglish languagesale 10% offe-Library read for1 day
This standard specifies the initial performance requirements and laboratory test methods for solar powered, hardwired and communicating active road studs intended for use as permanent and temporary road marking materials.
- Draft25 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the initial performance requirements and laboratory test methods for retroreflecting road studs intended for use as permanent and temporary road marking materials.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard describes a test method for carrying out road trials on retroreflecting road studs for use in both permanent and temporary applications. Specifications are given for test sites and for application patterns and a recommendation is given for the presentation of the results in the form of a test report.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for conducting road trials for road marking materials intended for use in both permanent and temporary road marking. Details are given for test sites, for the application of road marking materials on the test sites, for the parameters to be measured and the frequency of the measurements and for the presentation of the results in the form of a test report.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
This EN specifies the laboratory requirements and test methods for reflectorised and other road marking materials, both permanent and temporary.
- Standard42 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the performance for road users of white and yellow road markings, as expressed by their reflection in daylight or under road lighting, retroreflection in vehicle headlamp illumination, colour and skid resistance.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for wear simulator test for road marking materials intended for use in both permanent and temporary road markings including those with increased retroreflection under wet and rain conditions, without road studs.
It gives description for the equipment and for test plate’s characteristics; it also gives description for the test method involving road marking materials application, test conditions during wear test, parameters to be measured, frequency of the measurements and expression of the results as a test report.
This document gives also the requirements to be followed when the test is to be used for CE marking purposes.
- Standard24 pagesEnglish languagesale 10% offe-Library read for1 day
This standard specifies the laboratory requirements for the specific characteristics of, and the corresponding test methods for, new preformed road marking materials intended for permanent and temporary use. Most preformed road marking materials, hereafter referred to as 'preformed materials', do not change significantly their properties during application. For those materials the performance requirements for road users, in accordance with EN 1436, can be determined in the laboratory, before application on the road.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for laboratory tests (Product control) and qualification procedures for the following drop on materials used in road markings. These materials are dropped on to paints, thermoplastics, cold plastics and any other marking product applied in a liquid state, immediately after application to the road surface. The requirements taken into consideration in this standard are: - glass beads: granulometry, refractive index of the glass, chemical resistance, quality, surface treatments; - antiskid aggregates: granulometry, chemical characteristics, friability, colours.
- Amendment24 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for laboratory tests (Product control) and qualification procedures for the following drop on materials used in road markings. These materials are dropped on to paints, thermoplastics, coldplastics and any other marking product applied in a liquid state, immediately after application to the road surface.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard describes the methods for wear simulator tests on road marking materials for use as both permanent and temporary road markings including those with increased retroreflection under wet conditions, without road studs.
It gives requirements for wear simulator facilities, for application on the test plates, for parameters to be measured, frequency of the measurements and for expression of the results as a test report.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for factory production control (FPC) of road marking materials when the manufacturer wishes the products to bear the EC conformity marking.
This European Standard also gives guide for the manufacturer and the certification bodies involved with the factory production control of road marking materials. It specifies which types of test have to be taken into consideration within the FPC but, as usual in third-party assessment and surveillance of quality systems, it leaves the precise methods to be applied to be dependent on the characteristics of the manufacturer's installation and production methods. The precise parameters and methods will be found in the written procedures agreed between the manufacturer and the third party responsible for the initial assessment of the FPC.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard describes laboratory methods for the identification of road marking materials used in horizontal signalization.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
This Part specifies methods to obtain representative samples of road marking materials for testing and gives the appropriate test methods. The methods to obtain representative samples are described as appropriate for the main product types, i.e. paint, cold plastics, thermoplastics, premix glass beads, drop-on materials, preformed road markings and retroreflecting road studs.
- Standardization document11 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard gives guidance for conducting road trials for road marking materials intended for use in both permanent and temporary road marking. Recommendations are given for test sites, for the application of road marking materials on the test sites, for the parameters to be measured and the frequency of the measurements and for the presentation of the results in the form of a test report.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the initial performance requirements and laboratory test methods for retroreflecting road studs intended for use as permanent and temporary road marking materials.
- Amendment14 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the initial performance requirements and laboratory test methods for retroreflecting road studs intended for use as permanent and temporary road marking materials.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the performance for road users of white and yellow road markings, as expressed by their reflection in daylight or under road lighting, retroreflection in car headlamp illumination, colour and skid resistance.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day