SIST EN ISO 15609-6:2013

SLOVENSKI STANDARD
01-julij-2013
3RSLVLQNYDOLILNDFLMDYDULOQLKSRVWRSNRY]DNRYLQVNHPDWHULDOH6SHFLILNDFLMD
YDULOQHJDSRVWRSNDGHO2EORþQRKLEULGQRYDUMHQMH]ODVHUMHP,62

Specification and qualification of welding procedures for metallic materials - Welding
procedure specification - Part 6: Laser-arc hybrid welding (ISO 15609-6:2013)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe -
Schweißanweisung - Teil 6: Laserstrahl-Lichtbogen-Hybridschweißen (ISO 15609-
6:2013)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Descriptif d'un mode opératoire de soudage (ISO 15609-6:2013)
Ta slovenski standard je istoveten z: EN ISO 15609-6:2013
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 15609-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2013
ICS 25.160.10
English Version
Specification and qualification of welding procedures for metallic
materials - Welding procedure specification - Part 6: Laser-arc
hybrid welding (ISO 15609-6:2013)
Descriptif et qualification d'un mode opératoire de soudage Anforderung und Qualifizierung von Schweißverfahren für
pour les matériaux métalliques - Descriptif d'un mode metallische Werkstoffe - Schweißanweisung - Teil 6:
opératoire de soudage - Partie 6: Soudage hybride laser- Laserstrahl-Lichtbogen-Hybridschweißen (ISO 15609-
arc (ISO 15609-6:2013) 6:2013)
This European Standard was approved by CEN on 5 February 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15609-6:2013: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (EN ISO 15609-6:2013) has been prepared by Technical Committee ISO/TC 44 "Welding and
allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2013, and conflicting national standards shall be
withdrawn at the latest by September 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 15609-6:2013 has been approved by CEN as EN ISO 15609-6:2013 without any modification.
INTERNATIONAL ISO
STANDARD 15609-6
First edition
2013-04-01
Specification and qualification of
welding procedures for metallic
materials — Welding procedure
specification —
Part 6:
Laser-arc hybrid welding
Descriptif et qualification d’un mode opératoire de soudage pour les
matériaux métalliques — Descriptif d’un mode opératoire de soudage —
Partie 6: Soudage hybride laser-arc
Reference number
ISO 15609-6:2013(E)
©
ISO 2013
ISO 15609-6:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO 15609-6:2013(E)
Contents Page
Foreword .iv
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Technical contents of welding procedure specification (WPS) . 3
4.1 General . 3
4.2 Related to the manufacturer . 3
4.3 Related to the parent materials . 3
4.4 Welding process . 3
4.5 Joint design . 3
4.6 Welding position . 4
4.7 Joint preparation . 4
4.8 Welding technique . 4
4.9 Fixtures, jigs and tooling. 4
4.10 Backing . 4
4.11 Filler material. 4
4.12 Equipment used . 5
4.13 Welding parameters . 5
4.14 Thermal conditions . 7
4.15 Operations between runs and after welding . 7
Annex A (informative) Example of welding procedure specification for laser-arc hybrid welding .8
ISO 15609-6:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15609-6 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 10, Unification of requirements in the field of metal welding.
ISO 15609 consists of the following parts, under the general title Specification and qualification of welding
procedures for metallic materials — Welding procedure specification:
— Part 1: Arc welding
— Part 2: Gas welding
— Part 3: Electron beam welding
— Part 4: Laser beam welding and cladding
— Part 5: Resistance welding
— Part 6: Laser-arc hybrid welding
Requests for official interpretations of any aspect of this part of ISO 15609 should be directed to the
Secretariat of ISO/TC 44/SC 10 via your national standards body. A complete listing of these bodies can
be found at www.iso.org.
iv © ISO 2013 – All rights reserved

INTERNATIONAL STANDARD ISO 15609-6:2013(E)
Specification and qualification of welding procedures for
metallic materials — Welding procedure specification —
Part 6:
Laser-arc hybrid welding
1 Scope
This part of ISO 15609 specifies requirements for the content of welding procedure specifications for
laser-arc hybrid welding processes.
Variables listed in this part of ISO 15609 are those influencing the quality and the properties of the
welded joint.
NOTE Details of ISO 15609 (all parts) are given in ISO 15607:2003, Annex A.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the refe
...