ISO 7752-1:2010/Amd 1:2012
(Amendment)Cranes - Control layout and characteristics - Part 1: General principles - Amendment 1
Cranes - Control layout and characteristics - Part 1: General principles - Amendment 1
This part of ISO 7752 establishes principles and requirements for the controls of cranes. It deals with the arrangement of those controls used in positioning loads and serves as a general basis for the elaboration of detailed standards covering the controls of particular types of cranes.
Appareils de levage à charge suspendue — Disposition et caractéristiques des commandes — Partie 1: Principes généraux — Amendement 1
Žerjavi - Namestitev in karakteristike kontrolne opreme - 1. del: Splošna načela - Dopolnilo
Ta del standarda ISO 7752 določa načela in zahteve za krmilje žerjavov. Obravnava razporeditev krmilja, ki se uporablja za nameščanje bremen, in služi kot splošna podlaga za oblikovanje podrobnih standardov, ki zajemajo krmilja posebnih vrst žerjavov.
General Information
- Status
- Published
- Publication Date
- 18-Nov-2012
- Technical Committee
- ISO/TC 96/SC 7 - Tower cranes
- Drafting Committee
- ISO/TC 96/SC 7 - Tower cranes
- Current Stage
- 6060 - International Standard published
- Start Date
- 19-Nov-2012
- Due Date
- 13-Sep-2013
- Completion Date
- 13-Sep-2013
Relations
- Effective Date
- 21-Aug-2021
Overview
ISO 7752-1:2010/Amd 1:2012 amends the International Standard ISO 7752‑1 - Cranes: Control layout and characteristics - Part 1: General principles. It provides updated guidance on the general principles for the layout and functional characteristics of crane controls. Amendment 1 specifically integrates requirements for the use of remote control by referencing ISO 12480‑1:1997 (Crane - Safe use - Part 1: General). The work was prepared by ISO/TC 96 (Cranes), Subcommittee SC 7 (Tower cranes).
Keywords: ISO 7752‑1:2010/Amd 1:2012, crane control layout, crane control characteristics, remote control requirements, ISO 12480‑1, crane safety standards
Key topics and requirements
- General principles for control layout and characteristics
- Establishes the overarching principles that designers and manufacturers should use when arranging controls and defining their operational characteristics.
- Reference update
- Amendment 1 adds ISO 12480‑1:1997 to the normative references, linking control layout to safe-use guidance.
- Remote control requirements
- New subclause 5.2.7: use of remote control shall comply with ISO 12480‑1:1997, clause 8.3.2. This ensures consistency between control design and safety practices for remotely operated cranes.
- Scope and applicability
- Applies to cranes covered under ISO 7752 series and is especially relevant where control ergonomics, operator interface, and safety interlocks are specified at a general level.
Practical applications
- Crane designers and manufacturers
- Use the standard to define consistent control layouts and properties for new crane models, including provisions for remote-control integration.
- Safety and compliance teams
- Reference the amendment when developing conformity documentation, risk assessments, and operating procedures that involve remote control.
- Operators and training providers
- Inform training programs about expected control arrangements and the safety implications of remote operation as referenced to ISO 12480‑1.
- Regulatory bodies and inspectors
- Use the standard and its amendment when assessing compliance with national or industry safety requirements for control systems.
Related standards
- ISO 12480‑1:1997 - Cranes - Safe use - Part 1: General (normatively referenced by this amendment)
- ISO/TC 96 publications and other parts of the ISO 7752 series (for further, more specific guidance on control systems where applicable)
This amendment strengthens alignment between control layout guidance and safe-use rules for remote operation, helping stakeholders implement safer, standardized crane control systems.
Frequently Asked Questions
ISO 7752-1:2010/Amd 1:2012 is a standard published by the International Organization for Standardization (ISO). Its full title is "Cranes - Control layout and characteristics - Part 1: General principles - Amendment 1". This standard covers: This part of ISO 7752 establishes principles and requirements for the controls of cranes. It deals with the arrangement of those controls used in positioning loads and serves as a general basis for the elaboration of detailed standards covering the controls of particular types of cranes.
This part of ISO 7752 establishes principles and requirements for the controls of cranes. It deals with the arrangement of those controls used in positioning loads and serves as a general basis for the elaboration of detailed standards covering the controls of particular types of cranes.
ISO 7752-1:2010/Amd 1:2012 is classified under the following ICS (International Classification for Standards) categories: 53.020.01 - Lifting appliances in general. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 7752-1:2010/Amd 1:2012 has the following relationships with other standards: It is inter standard links to ISO 7752-1:2010. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
ISO 7752-1:2010/Amd 1:2012 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 7752-1
Second edition
2010-06-01
AMENDMENT 1
2012-12-01
Cranes — Control layout and
characteristics —
Part 1:
General principles
AMENDMENT 1
Appareils de levage à charge suspendue — Disposition et
caractéristiques des commandes —
Partie 1: Principes généraux
AMENDEMENT 1
Reference number
ISO 7752-1:2010/Amd.1:2012(E)
©
ISO 2012
ISO 7752-1:2010/Amd.1:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
ISO 7752-1:2010/Amd.1:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take pa
...
NORME ISO
INTERNATIONALE 7752-1
Deuxième édition
2010-06-01
AMENDEMENT 1
2012-12-01
Appareils de levage à charge
suspendue — Disposition et
caractéristiques des commandes —
Partie 1:
Principes généraux
AMENDEMENT 1
Cranes — Control Layout and characteristics —
Part 1: General principles
Amendment 1
Numéro de référence
ISO 7752-1:2010/Amd.1:2012(F)
©
ISO 2012
ISO 7752-1:2010/Amd.1:2012(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l’accord écrit
de l’ISO à l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2012 – Tous droits réservés
ISO 7752-1:2010/Amd.1:2012(F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux de
normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général confiée aux
comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales,
en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la n
...
SLOVENSKI STANDARD
01-junij-2013
äHUMDYL1DPHVWLWHYLQNDUDNWHULVWLNHNRQWUROQHRSUHPHGHO 6SORãQDQDþHOD
'RSROQLOR
Cranes - Control layout and characteristics - Part 1: General principles - Amendment
Appareils de levage à charge suspendue - Disposition et caractéristiques des
commandes - Partie 1: Principes généraux
Ta slovenski standard je istoveten z: ISO 7752-1:2010/Amd 1:2012
ICS:
53.020.20 Dvigala Cranes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 7752-1
Second edition
2010-06-01
AMENDMENT 1
2012-12-01
Cranes — Control layout and
characteristics —
Part 1:
General principles
AMENDMENT 1
Appareils de levage à charge suspendue — Disposition et
caractéristiques des commandes —
Partie 1: Principes généraux
AMENDEMENT 1
Reference number
ISO 7752-1:2010/Amd.1:2012(E)
©
ISO 2012
ISO 7752-1:2010/Amd.1:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
ISO 7752-1:2010/Amd.1:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...