IEC TR 62343-6-10:2017
(Main)Dynamic modules - Part 6-10: Design guide - Intermediate controller for multiple dynamic module systems
Dynamic modules - Part 6-10: Design guide - Intermediate controller for multiple dynamic module systems
IEC TR 62343-6-10:2017(E) which is a Technical Report, discusses the rationale, conceptual definition, and minimum list of functions for an intermediate controller that delivers a dynamic control signal to multiple dynamic modules. These modules are included in an optical-switch-based network node, according to the upper layer controller of software-defined optical networking.
General Information
Standards Content (Sample)
IEC TR 62343-6-10 ®
Edition 1.0 2017-03
TECHNICAL
REPORT
colour
inside
Dynamic modules –
Part 6-10: Design guide – Intermediate controller for multiple dynamic module
systems
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
IEC TR 62343-6-10 ®
Edition 1.0 2017-03
TECHNICAL
REPORT
colour
inside
Dynamic modules –
Part 6-10: Design guide – Intermediate controller for multiple dynamic module
systems
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.180.01, 33.180.99 ISBN 978-2-8322-4127-1
– 2 – IEC 62343-6-10:2017 © IEC 2017
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviated terms . 6
3.1 Terms and definitions . 6
3.2 Abbreviated terms . 6
4 Background of the software defined networking and its control plane for optical
nodes . 7
5 Research activities on high-performance node systems where intermediate
controller plays key role . 7
5.1 Photonic network with OpenFlow® controller . 7
5.2 Dynamic optical path network with a network controller . 7
5.3 Control interface of the Photonic Layer-2 . 8
6 Intermediate controller for multiple dynamic module systems . 8
6.1 Description of the controller . 8
6.1.1 Controller of multiple dynamic modules for a network node . 8
6.1.2 Structure of the intermediate controller . 9
6.2 Functions . 10
6.3 Shared information between the control interface and the network control
plane . 11
7 Example of multi-degree ROADM systems . 12
8 Conclusion . 14
Bibliography . 15
Figure 1 – Conceptual block of the control interface for multiple dynamic modules and
network devices . 8
Figure 2 – Basic block of the control interface for multiple dynamic modules. 9
Figure 3 – Difference between connection information and configuration information . 10
Figure 4 – Function coverage of the intermediate controller . 11
Figure 5 – Example of a multiple dynamic module system . 12
Figure 6 – Example of 4-degree ROADM node architecture . 13
Figure 7 – 3-degree ROADM node with colourless, non-directional add/drop ports . 13
Figure 8 – Compact PLC-based transponder aggregator for colourless and
directionless ROADM . 14
Table 1 – Shared information in the intermediate controller . 12
IEC 62343-6-10:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DYNAMIC MODULES –
Part 6-10: Design guide – Intermediate controller
for multiple dynamic module systems
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
The main task of IEC technical committees is to prepare International Standards. However, a
technical committee may propose the publication of a technical report when it has collected
data of a different kind from that which is normally published as an International Standard, for
example "state of the art".
IEC TR 62343-6-10, which is a technical report, has been prepared by subcommittee 86C:
Fibre optic systems and active devices, of IEC technical committee TC 86: Fibre optics.
The text of this technical report is based on the following documents:
Enquiry draft Report on voting
86C/1381/DTR 86C/1422/RVC
– 4 – IEC 62343-6-10:2017 © IEC 2017
Full information on the voting for the approval of this technical report can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 62343 series, published under the general title Dynamic modules,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
IEC 62343-6-10:2017 © IEC 2017 – 5 –
INTRODUCTION
Software defined networking (SDN) technology is widely recognized as a promising solution
for flexible and efficient provisioning of networks by virtualizing their infrastructures, which
results in cost-effective realization of high capacity, low energy consumption and even low
latency. SDN technology will remain highly influential over global industries, societies, and the
environment for many years to come.
Optical fibre communication technology has offered sufficient transport capacity with a fixed
physical topology. However, recent technological progress in optical networking enables
physical reconfiguration of optical paths by controlling multiple dynamic modules such as
wavelength division multiplexing (WDM) devices and switching devices. Here, the key is to
have an intermediate controller that controls and maintains the multiple dynamic modules in
an integrated fashion, according to the upper layer controller of the SDN.
In order to realize such a reconfigurable and/or dynamically switchable optical network
infrastructures at a hardware level in a cost-effective, reliable, scalable and low-carbon
manner, it is important to initiate, in a timely manner and to a wide extent, conceptual and
technical discussions, particularly on the intermediate controller for future standardization.
It is very important for industries to identify requirements for network architecture and
devices/components in a timely manner, and to improve the technology development and
investment efficiencies.
The objective of this part of IEC 62343 is to contribute to the standardization of basic
requirements of the dynamic optical path networks using the intermediate controller.
– 6 – IEC 62343-6-10:2017 © IEC 2017
DYNAMIC MODULES –
Part 6-10: Design guide – Intermediate controller
for multiple dynamic mod
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.