IEC 61534-1:2011/COR1:2013
(Corrigendum)Corrigendum 1 - Powertrack systems - Part 1: General requirements
Corrigendum 1 - Powertrack systems - Part 1: General requirements
Corrigendum 1 - Systèmes de conducteurs préfabriqués - Partie 1: Exigences générales
General Information
Relations
Standards Content (Sample)
IEC 61534-1 CEI 61534-1
(Second edition – 2011) (Deuxième édition – 2011)
Powertrack systems – Systèmes de conducteurs préfabriqués –
Part 1: General requirements Partie 1: Exigences générales
CO RRI G E NDUM 1
...
This May Also Interest You
- Standard20 pagesEnglish and French languagesale 15% off
IEC 61534-1:2011 specifies general requirements and tests for powertrack (PT) systems with a rated voltage not exceeding 277 V a.c. single phase, or 480 V a.c. two or three phase 50 Hz/60 Hz with a rated current not exceeding 63 A. These systems are used for distributing electricity in household, commercial and industrial premises. This second edition cancels and replaces the first edition published in 2003 and constitutes a technical revision. The main changes from the previous edition are as follows:
- updated normative references (Clause 2);
- changes to the number of samples to be tested (Subclause 5.3);
- inclusion of a short circuit test (New Clause 18);
- changes to external influences (Clause 21). The contents of the corrigendum apply to the French version only.
- Standard137 pagesEnglish and French languagesale 15% off
- Standard278 pagesEnglish and French languagesale 15% off
- Standard285 pagesEnglish and French languagesale 15% off
- Standard8 pagesEnglish and French languagesale 15% off
- Standard20 pagesEnglish and French languagesale 15% off
IEC 61534-1:2011 specifies general requirements and tests for powertrack (PT) systems with a rated voltage not exceeding 277 V a.c. single phase, or 480 V a.c. two or three phase 50 Hz/60 Hz with a rated current not exceeding 63 A. These systems are used for distributing electricity in household, commercial and industrial premises. This second edition cancels and replaces the first edition published in 2003 and constitutes a technical revision. The main changes from the previous edition are as follows:
- updated normative references (Clause 2);
- changes to the number of samples to be tested (Subclause 5.3);
- inclusion of a short circuit test (New Clause 18);
- changes to external influences (Clause 21). The contents of the corrigendum apply to the French version only.
- Standard137 pagesEnglish and French languagesale 15% off
- Standard278 pagesEnglish and French languagesale 15% off
- Standard285 pagesEnglish and French languagesale 15% off
- Standard8 pagesEnglish and French languagesale 15% off
IEC/IEEE 62582-1:2024 is available as IEC/IEEE 62582-1:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC/IEEE 62582-1:2024 contains requirements for application of the other parts of IEC/IEEE 62582 related to specific methods for condition monitoring in electrical equipment important to safety of nuclear power plants. It also includes requirements which are common to all methods. The procedures defined in IEC/IEEE 62582 are intended for detailed condition monitoring.
IEC/IEEE 62582 specifies condition monitoring methods in sufficient detail to enhance the accuracy and repeatability, and provide standard formats for reporting the results. The methods specified are applicable to electrical equipment containing polymeric materials. Some methods are especially designed for the measurement of condition of a limited range of equipment whilst others can be applied to all types of equipment for which the polymeric parts are accessible.
- Standard21 pagesEnglish languagesale 15% off
- Standard21 pagesEnglish languagesale 15% off
IEC/IEEE 63332-387:2024 defines the criteria for the application and testing of diesel generator (DG) units used as safety class standby power supplies in nuclear facilities. In general, the standard applies to new nuclear facilities as well as for upgrading or back-fitting of existing facilities. Existing facilities can voluntarily adopt the requirements to enhance the performance capabilities and reliability of the installed DG units. The standard can be used in applications where highly reliable onsite alternating current (AC) power source is required to maintain plant safety following an event with potential loss of offsite power for an extended duration.
This document provides the principal design criteria, the design features, testing, and qualification requirements for the individual DG units that enable them to meet their functional requirements as a part of the standby power supply under the conditions produced by the design basis events catalogued in the plant safety analysis.
- Standard139 pagesEnglish and French languagesale 15% off
IEC TR 63368:2024 provides guidance on off-site real-time simulation tests of control and protection (C&P) systems for HVDC power transmission systems. The off-site real-time simulation tests are carried out after the testing of C&P devices and prior to on-site system tests.
This document covers point-to-point, back-to-back, and multi-terminal HVDC systems of line commutated converters (LCC), voltage-sourced converters (VSC) and hybrid HVDC technologies.
In order to provide practical guidance for the functional performance tests of HVDC power transmission systems, this document covers the test environment, the contents and methods of functional performance tests, and the test report.
- Technical report30 pagesEnglish languagesale 15% off
IEC 62899-301-3:2024 defines measurement terms and methods related to the shape errors of printing plate rollers. Measurement terms include radius, total run-out, and three kinds of shape errors of printing plate rollers that are axial deviation, radial deviation, and cross-sectional deviation. The remaining shape error excluding the three errors mentioned above is defined as a residual shape error.
This document applies to printing plate rollers with or without patterns while excluding the pattern area for the measurement.
- Standard24 pagesEnglish languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.