EN IEC 60966-3-3:2023

SLOVENSKI STANDARD
01-junij-2023
Sestavi radiofrekvenčnih in koaksialnih kablov - 3-3. del: Podrobna specifikacija za
delno upogibljive kabelske sklope (prevezava), frekvenčno območje do 18 GHz,
delno upogibljiv koaksialni kabel tipa 50-141 (IEC 60966-3-3:2023)
Radio frequency and coaxial cable assemblies - Part 3-3: Detail specification for semi-
flexible cable assemblies (Jumper) - Frequency range up to 18 GHz, Type 50-141 semi-
flexible coaxial cable (IEC 60966-3-3:2023)
Konfektionierte Koaxial- und Hochfrequenzkabel – Teil 3-3: Einzelspezifikation für
semiflexible Kabelkonfektionen (Jumper), Frequenzbereich bis 18 GHz, Typ 50-141
semiflexibles Koaxialkabel (IEC 60966-3-3:2023)
Cordons coaxiaux et cordons pour fréquences radioélectriques - Partie 3-3 :
Spécification particulière relative aux cordons semi-flexibles (câble de pontage), bande
de fréquences jusqu’à 18 GHz, câble coaxial semi-flexible de type 50-141 (IEC 60966-3-
3:2023)
Ta slovenski standard je istoveten z: EN IEC 60966-3-3:2023
ICS:
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60966-3-3

NORME EUROPÉENNE
EUROPÄISCHE NORM April 2023
ICS 33.120.10; 33.120.01
English Version
Radio frequency and coaxial cable assemblies - Part 3-3: Detail
specification for semi-flexible cable assemblies (jumper) -
Frequency range up to 18 GHz, Type 50-141 semi-flexible
coaxial cable
(IEC 60966-3-3:2023)
Cordons coaxiaux et cordons pour fréquences Konfektionierte Koaxial- und Hochfrequenzkabel - Teil 3-3:
radioélectriques - Partie 3-3: Spécification particulière Einzelspezifikation für semiflexible Kabelkonfektionen
relative aux cordons semi-flexibles (câble de liaison), plage (Jumper), Frequenzbereich bis 18 GHz, Typ 50-141
de fréquences jusqu'à 18 GHz, câble coaxial semi-flexible semiflexibles Koaxialkabel
de type 50-141 (IEC 60966-3-3:2023)
(IEC 60966-3-3:2023)
This European Standard was approved by CENELEC on 2023-04-11. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60966-3-3:2023 E

European foreword
The text of document 46/927/FDIS, future edition 1 of IEC 60966-3-3, prepared by IEC/TC 46 "Cables,
wires, waveguides, RF connectors, RF and microwave passive components and accessories" was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 60966-3-3:2023.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2024-01-11
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2026-04-11
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60966-3-3:2023 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-2-11 - Environmental testing - Part 2-11: Tests - EN IEC 60068-2-11 -
Test Ka: Salt mist
IEC 60966-1 2019 Radio frequency and coaxial cable EN IEC 60966-1 2019
assemblies - Part 1: Generic specification -
General requirements and test methods
IEC 60966-3 - Radio frequency and coaxial cable EN 60966-3 -
assemblies - Part 3: Sectional specification
for semi-flexible coaxial cable assemblies
IEC 60966-3-1 - Radio frequency and coaxial cable EN 60966-3-1 -
assemblies - Part 3-1: Blank detail
specification for semi-flexible coaxial cable
assemblies
IEC 61169-15 - Radio-frequency connectors - Part 15: EN IEC 61169-15 -
Sectional specification - RF coaxial
connectors with inner diameter of outer
conductor 4,13 mm (0,163 in) with
threaded coupling - Characteristic
impedance 50 Ω (type SMA)
IEC 61169-16 - Radio-frequency connectors - Part 16: EN 61169-16 -
Sectional specification - RF coaxial
connectors with inner diameter of outer
conductor 7 mm (0,276 in) with screw
coupling - Characteristics impedance 50
ohms (75 ohms) (type N)
IEC 61196-8-4 - Coaxial communication cables - Part 8-4: - -
Detail specification for 50-141 type semi-
flexible cables with solid
polytetrafluoroethylene (PTFE) insulation
IEC 61726 - Cable assemblies, cables, connectors and EN IEC 61726 -
passive microwave components -
Screening attenuation measurement by the
reverberation chamber method
IEC 60966-3-3 ®
Edition 1.0 2023-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
HORIZONTAL PUBLICATION
PUBLICATION HORIZONTALE
Radio frequency and coaxial cable assemblies –

Part 3-3: Detail specification for semi-flexible cable assemblies (Jumper) –

Frequency range up to 18 GHz, Type 50‑141 semi-flexible coaxial cable

Cordons coaxiaux et cordons pour fréquences radioélectriques –

Partie 3-3: Spécification particulière relative aux cordons semi-flexibles (câble

de liaison), plage de fréquences jusqu’à 18 GHz, câble coaxial semi-flexible de

type 50-141
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.01; 33.120.10 ISBN 978-2-8322-6535-2

– 2 – IEC 60966-3-3:2023 © IEC 2023
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Detail specification . 7
Annex A (informative) Identification and marking . 12
A.1 Identification – Type name . 12
A.2 Cable assemblies marking . 12
Bibliography . 13

Figure 1 – Length definition of cable assemblies . 7
Figure 2 – Semi-flexible cable assemblies with type 50-141 semi-flexible coaxial cable . 7

Table A.1 – The meaning of connector variants . 12

IEC 60966-3-3:2023 © IEC 2023 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO FREQUENCY AND COAXIAL CABLE ASSEMBLIES –

Part 3-3: Detail specification for semi-flexible cable assemblies (Jumper) –
Frequency range up to 18 GHz, Type 50‑141 semi-flexible coaxial cable

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 60966-3-3 has been prepared by IEC technical committee 46: Cables, wires, waveguides,
RF connectors, RF and microwave passive components and accessories. It is an International
Standard.
It has the status of a horizontal standard in accordance with IEC Guide 108.
The text of this International Standard is based on the following documents:
Draft Report on voting
46/927/FDIS 46/931/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.

– 4 – IEC 60966-3-3:2023 © IEC 2023
A list of all parts in the IEC 60966 series, published under the general title Radio frequency and
coaxial cable assemblies, can be found on the IEC website.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supp
...