EN 4840-001:2018

SLOVENSKI STANDARD
01-november-2018
$HURQDYWLND7RSORWQRVNUþOMLYHXOLWHIRUPHGHO7HKQLþQDVSHFLILNDFLMD
Aerospace series - Heat shrinkable moulded shapes - Part 001: Technical specification
Luft- und Raumfahrt - Wärmeschrumpfende Formteile - Teil 001: Technische
Spezifikation
Série aérospatiale - Manchons thermorétractables - Partie 001 : Spécification technique
Ta slovenski standard je istoveten z: EN 4840-001:2018
ICS:
49.025.40 Guma in polimerni materiali Rubber and plastics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 4840-001
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2018
EUROPÄISCHE NORM
ICS 29.035.20; 49.060
English Version
Aerospace series - Heat shrinkable moulded shapes - Part
001: Technical specification
Série aérospatiale - Manchons thermorétractables - Luft- und Raumfahrt - Wärmeschrumpfende Formteile
Partie 001 : Spécification technique - Teil 001: Technische Lieferbedingungen
This European Standard was approved by CEN on 18 January 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4840-001:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Scope . 4
Normative references . 4
Definitions and symbols . 4
Materials and characteristics . 4
Required properties . 5
Test methods . 5
Quality assurance . 7
Labelling and packaging . 9
Annex A (Informative) Storage recommendations . 10

European foreword
This document (EN 4840-001:2018) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2019, and conflicting national standards shall
be withdrawn at the latest by February 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Scope
This European standard specifies the required characteristics, test methods, qualification and production
routine testing of heat shrinkable moulded shapes.
Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 3475-100, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 100: General
EN 4840-002, Aerospace series — Heat shrinkable moulded shapes — Part 002: Index of product standards
and product dimensions
EN 9133, Aerospace series — Quality Management Systems — Qualification Procedure for Aerospace
Standard Parts
EN ISO 4892-2, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
1)
IEC 60304, Standard colours for insulation for low-frequency cables and wires
1)
IEC 62329-2, Heat-shrinkable moulded shapes — Part 2: Methods of test
IEC 62329-3, Heat-shrinkable moulded shapes — Part 3: Specification requirements for shape dimensions,
material requirements and compatibility performance — Sheet 100: Heat-shrinkable moulded shape
1)
dimensions
Definitions and symbols
For the purposes of this document, the definitions and symbols given in EN 3475-100 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
Materials and characteristics
General
The moulded shapes shall be made from materials that ensure the finished product conform to the product
standard.
Material types
See product standards.
1)
Published by: IEC International Electrotechnical Commission http://www.iec.ch/
Finish
The moulded shapes, both before and after unrestricted shrinkage, shall be free from bubbles, pinholes,
creases and other defects that may affect performance.
Dimensions
As detailed in EN 4840-002.
Temperature range
See product standard.
Shelf life
The use by date shall be the guaranteed minimum storage time for which the moulded shape retains the
“as supplied” internal diameter. Following unrestricted shr
...