EN ISO 13297:2014

SLOVENSKI STANDARD
01-marec-2015
1DGRPHãþD
SIST EN ISO 13297:2013
0DODSORYLOD(OHNWULþQLVLVWHPL,QãWDODFLMH]DL]PHQLþQLWRN,62
Small craft - Electrical systems - Alternating current installations (ISO 13297:2014)
Kleine Wasserfahrzeuge - Elektrische Systeme - Wechselstromanlagen (ISO
13297:2014)
Petits navires - Systèmes électriques - Installations à courant alternatif (ISO 13297:2014)
Ta slovenski standard je istoveten z: EN ISO 13297:2014
ICS:
47.020.60 (OHNWULþQDRSUHPDODGLMLQ Electrical equipment of ships
NRQVWUXNFLMQDPRUMX and of marine structures
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 13297
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2014
ICS 47.080 Supersedes EN ISO 13297:2012
English Version
Small craft - Electrical systems - Alternating current installations
(ISO 13297:2014)
Petits navires - Systèmes électriques - Installations à Kleine Wasserfahrzeuge - Elektrische Systeme -
courant alternatif (ISO 13297:2014) Wechselstromanlagen (ISO 13297:2014)
This European Standard was approved by CEN on 13 September 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13297:2014 E
worldwide for CEN national Members.

Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive 2003/44/EC .4
Foreword
This document (EN ISO 13297:2014) has been prepared by Technical Committee ISO/TC 188 “Small craft”.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2015, and conflicting national standards shall be withdrawn at
the latest by June 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13297:2012.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 13297:2014 has been approved by CEN as EN ISO 13297:2014 without any modification.

Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive
2003/44/EC
This European standard has been prepared under a mandate given to CEN by the European Commission to
provide one means of conforming to Essential Requirements of the New Approach Directive 94/25/EC as
amended by Directive 2003/44/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive and has
been implemented as a national standard in at least one member state, compliance with the normative
clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a
presumption of conformity with the relevant Essential Requirements of that Directive and associated EFTA
regulations.
Table ZA.1 - Correspondence between this European Standard and Directive 94/25/EC as amended by
Directive 2003/44/EC
Clauses/sub-clauses Corresponding annexes/ Comments
Paragraphs of Directive
Of this European Standard
94/25/EC as amended
2003/44/EC
All clauses Annex IA, Clause 5.3 Electrical The scope of this standard is
systems limited to the design,
construction and installation of
low-voltage alternating current
electrical systems which operate
at nominal voltages of less than
250 V single phase
Clause 11.12 Annex IA, Clause 5.6.1 Fire In respect of avoiding wiring
protection above hot areas of machines
Annex B Annex IA, Clause 2.5 Owner’s
manual
WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling within the
scope of this standard.
INTERNATIONAL ISO
STANDARD 13297
Fourth edition
2014-12-01
Small craft — Electrical systems —
Alternating current installations
Petits navires — Systèmes électriques — Installations à courant
alternatif
Reference number
ISO 13297:2014(E)
©
ISO 2014
ISO 13297:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

ISO 13297:2014(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 4
5 Marking . 6
6 Ignition sources . 7
7 Overcurrent protection . 7
7.1 General . 7
7.2 Supply circuits . 8
7.3 Branch circuits . 8
8 Ground-fault protection/earth-leakage protection . 8
9 Appliances and equipment . 9
10 System wiring. 9
11 Conductor and cable installation .10
12 Panel boards (switchboards) .11
13 Socket outlets
........................................................................................................................................................................................................12
14 Power source options .12
15 Inverters and inverter/chargers .13
Annex A (normative) Conductor requirements .15
Annex B (normative) Instructions to be included with owner’s manual.17
Annex C (informative) Recommended system tests .18
Annex D (informative) Typical a.c. system diagrams .19
Bibliography .27
ISO 13297:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 188, Small craft.
This fourth edition cancels and replaces the third edition (ISO 13297:2012), of which it constitutes a
minor revision. The main changes are:
—
...