EN 1034-13:2005+A1:2009

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 13: Maschinen zur Entdrahtung von Ballen und UnitsSécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 13: Machines à couper les fils des balles et unitésSafety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 13: Machines for de-wiring bales and units85.100Oprema za papirno industrijoEquipment for the paper industry21.020Characteristics and design of machines, apparatus, equipment13.110Varnost strojevSafety of machineryICS:Ta slovenski standard je istoveten z:EN 1034-13:2005+A1:2009SIST EN 1034-13:2006+A1:2010en,fr01-februar-2010SIST EN 1034-13:2006+A1:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1034-13:2005+A1
December 2009 ICS 85.100 Supersedes EN 1034-13:2005English Version
Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 13: Machines for de-wiring bales and units
Sécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 13: Machines à couper les fils des balles et unités
Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 13: Maschinen zur Entdrahtung von Ballen und Units This European Standard was approved by CEN on 6 October 2005 and includes Amendment 1 approved by CEN on 17 November 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1034-13:2005+A1:2009: ESIST EN 1034-13:2006+A1:2010

Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC . 13Annex ZB (informative)
!!!!Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC"""" . 14 Figures Figure 1 — Example of a machine for cutting bale wires . 6 Figure 2 — Example of a machine for unit de-wiring . 6 Figure 3 — Example of a machine for de-wiring cellulose bales . 7
Tables
Table 1 —
List of significant hazards . 8 Table 2 — Methods used to verify safety requirements and/or measures . 12 SIST EN 1034-13:2006+A1:2010

Foreword This document (EN 1034-13:2005+A1:2009) has been prepared by Technical Committee CEN/TC 198 “Printing and paper machinery - Safety”, the secretariat of which is held by DIN. This document shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at the latest by June 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 17 November 2009. This document supersedes EN 1034-13:2005. The start and finish of text introduced or altered by amendment is indicated in the text by tags !". !This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document." According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 1034-13:2006+A1:2010

The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this European Standard.
For machines that have been designed and built according to the provisions of this C standard, the following stipulation applies: When provisions of this type C standard are different from those which are stated in type B standards or from provisions made in !EN 1034-1:2000+A1:2010", the provisions of this type C standard take precedence over the provisions of the other standards. 1 Scope This European Standard applies to machines for de-wiring bales and units and shall be used together with !EN 1034-1:2000+A1:2010". It deals with all significant hazards, hazardous situations and hazard events relevant to machines for de-wiring bales and units, when used as intended and under conditions reasonably foreseeable by the manufacturer as incorrect application (see clause 4).
This European Standard is not applicable to hand-held devices. This European Standard is not applicable to machines for de-wiring bales and units which are manufactured before the date of publication of this document by CEN. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 294:1992, Safety of machinery — Safety distances to prevent danger zones being reached by the upper limbs. EN 418:1992, Safety of machinery — Emergency stop equipment — Functional aspects — Principles for design. EN 619:2002, Continuous conveyors and systems — Safety and EMC requirements for mechanical conveying systems for packaged goods. EN 953:1997, Safety of machinery — Guards — General requirements for the design and construction of fixed and movable guards. EN 954-1:1996, Safety of machinery — Safety related parts of control systems — Part 1: General principles for design. EN 982:1996, Safety of machinery — Safety requirements for fluid power systems and their components — Hydraulics. EN 983:1996, Safety of machinery — Safety requirements for fluid power systems and their components —Pneumatics. SIST EN 1034-13:2006+A1:2010

(IEC 60204-1:1997).
EN 61000-6-2:2001, Electromagnetic compatibility (EMC) — Part 6-2: Generic standard — Immunity —
Part 2: Industrial environment (IEC 61000-6-2:1999, modified). EN 61496-1:2004, Safety of machinery — Electro-sensitive protective equipment — Part 1: General requirements and tests (IEC 61496-1:2004, modified). prEN 61496-2:1997, Safety of machinery — Electro-sensitive protective equipment — Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:1997, modified). EN ISO12100-1:2003, Safety of machinery — Basic concepts — General principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003). EN ISO 12100-2:2003, Safety of machinery — Basic concepts — General principles for design - Part 2: Technical principles and specifications (ISO 12100-2:2003).
3 Terms and definitions For the purpose of this European Standard, the definitions given in !EN 1034-1:2000+A1:2010", EN ISO 12100-1:2003 and the following apply: 3.1 machine for de-wiring bales and units
machinery used for cutting and or opening and removing wires used for binding together bales made of cellulose or paper and units formed of cellulose bales. This machinery includes the de-wiring device, integrated continuous conveyor for moving the bales and units, the loading conveyor, the positioning device and the wire ejection device, including the drive and control systems.
Examples of machine types are illustrated in Figures 1, 2 and 3.
NOTE Safety devices are not shown Key 1 Loading conveyor 2 Movable blade 3 Control cabinet Figure 1 — Example of a machine for cutting bale wires
NOTE Safety devices are not shown Key 1 Wire ejection 2 Feed direction 3 Cutting tool Figure 2 — Example of a machine for unit de-wiring 123SIST EN 1034-13:2006+A1:2010

NOTE Safety devices are not shown Key 1 Feed direction 2 Movable cutting tool 3 Loading conveyor
4 Positioning device 5 Continuous conveyor Figure 3 — Example of a machine for de-wiring cellulose bales 3.2 de-wiring device device with tools for cutting/opening, gripping and removing the wires, including drive 3.3 loading conveyor continuous convey
...