EN ISO 11252:2013

SLOVENSKI STANDARD
01-november-2013
1DGRPHãþD
SIST EN ISO 11252:2008
Laserji in laserska oprema - Laserska naprava - Minimalne zahteve za
dokumentacijo (ISO 11252:2013)
Lasers and laser-related equipment - Laser device - Minimum requirements for
documentation (ISO 11252:2013)
Laser und Laseranlagen - Lasergerät - Mindestanforderungen an die Dokumentation
(ISO 11252:2013)
Lasers et équipements associés aux lasers - Source laser - Exigences minimales pour la
documentation (ISO 11252:2013)
Ta slovenski standard je istoveten z: EN ISO 11252:2013
ICS:
31.260 Optoelektronika, laserska Optoelectronics. Laser
oprema equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11252
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2013
ICS 31.260 Supersedes EN ISO 11252:2004
English Version
Lasers and laser-related equipment - Laser device - Minimum
requirements for documentation (ISO 11252:2013)
Lasers et équipements associés aux lasers - Source laser - Laser und Laseranlagen - Lasergerät -
Exigences minimales pour la documentation (ISO Mindestanforderungen an die Dokumentation (ISO
11252:2013) 11252:2013)
This European Standard was approved by CEN on 7 March 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11252:2013: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC (Machinery) .4

Foreword
This document (EN ISO 11252:2013) has been prepared by Technical Committee ISO/TC 172 "Optics and
photonics" in collaboration with Technical Committee CEN/TC 123 “Lasers and photonics” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2014, and conflicting national standards shall be withdrawn
at the latest by February 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11252:2004.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11252:2013 has been approved by CEN as EN ISO 11252:2013 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC (Machinery)
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2006/42/EC on machinery.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard confers, within the limits of the scope of this standard, a presumption of conformity with the
relevant Essential Requirements of that Directive and associated EFTA regulations.

WARNING — Other requirements and other EC Directives may be applicable to the product(s) falling within
the scope of this standard.
INTERNATIONAL ISO
STANDARD 11252
Third edition
2013-08-01
Lasers and laser-related equipment —
Laser device — Minimum
requirements for documentation
Lasers et équipements associés aux lasers — Source laser —
Exigences minimales pour la documentation
Reference number
ISO 11252:2013(E)
©
ISO 2013
ISO 11252:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO 11252:2013(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Units . 2
5 Technical data sheet. 2
5.1 General . 2
5.2 Beam output characteristics . 2
5.3 Electrical and non-electrical power supply. 3
5.4 Liquids and gases . 4
5.5 Environmental conditions . 4
5.6 Mechanical parts and interfaces . 4
5.7 Safety . 4
6 Information for the user . 5
7 Marking and labelling . 6
Annex A (informative) Model of technical data sheet . 7
Bibliography .12
ISO 11252:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11252 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 9,
Electro-optical systems.
This third edition cancels and replaces the second edition (ISO 11252:2004), which has been
technically revised.
iv © ISO 2013 – All rights reserved

ISO 11252:2013(E)
Introduction
This document is a type B1 standard as stated in ISO 12100.
The provisions of this document may be supplemented or modified by a type C standard.
NOTE For machines which are covered by the scope of a type C standard and which have been designed and
built according to the provisions of that standard, the provisions of that type C standard take precedence over the
provisions of this type B1 standard.
ISO 11252 covers both laser systems and laser products according to IEC 60825-1, and laser devices,
units or laser processing machines according to ISO 11145, ISO 11553-1 and ISO 11553-2. Although
within these standards different terminology, terms and definitions are used, ISO 11252 brings together
basic requirements for documentation.
INTERNATIONAL STANDARD ISO 11252:2013(E)
Lasers and laser-related equipment — Laser device —
Minimum requirements for documentation
1 Scope
This International Standard specifies the minimum documentation, marking and labelling for all laser
products classified in accordance with IEC 60825-1 including laser diodes and all laser devices defined
in ISO 11145.
It is applicable to laser systems being integrated in a laser product in accordance with IEC 60825-1 and
laser devices being integrated in a laser unit or processing machine in accordance with ISO 11553-1
and ISO 11553-2.
This International Standard is not applicable to (ready-to-use) complete laser products, embedded laser
products without external laser emission by means of protective enclosure or laser processing machines
that incorporate a laser device.
This International Standard is not applicable to incoherent lamps and other similar sources such as
LEDs that are required to comply with IEC 62471.
This International Standard specifies requirements for technical data sheets (see Clause 5) and
information for the user (see Clause 6).
The requirements in this International Standard augment but do not supersede any of the requirements
in IEC 60825-1.
NOTE 1 The provision of technical data and safety information is an integral part of a product and is essential
for its safe use. The documentation covers the whole life cycle, transport, assembly, system integration, normal
operation, maintenance, service, decommissioning and disposal.
NOTE 2 For incomplete (not ready-to-use) machines, the manufacturer/supplier is responsible for the
documentation with regard to all components provided by him.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 11145, Optics and photonics — Lasers and laser-related equipment — Vocabulary and symbols
ISO 11146-1, Lasers and laser-related equipment — Test methods for laser beam widths, divergence angles
and beam propagation ratios — Part 1: Stigmatic and simple astigmatic beams
ISO 11146-2, Lasers and laser-related equipment — Test methods for laser beam widths, divergence angles
and beam propagation ratios — Part 2: General astigmatic beams
ISO 11553-3, Safety of machinery — Laser processing machines — Part 3: Noise reduction and noise
measurement methods for laser processing machines and hand-held processing devices and associated
auxiliary equipment (accuracy grade 2)
ISO 11554, Optics and photonics — Lasers and laser-related equipment — Test methods for laser beam
power, energy and temporal characteristics
ISO 11670, Lasers and laser-related equipment — Test methods for laser beam parameters — Beam
positional stability
ISO 11252:2013(E)
ISO 12005, Lasers and laser-related equipment — Test methods for laser beam parameters — Polarization
ISO 13694, Optics and optical instruments — Lasers and laser-related equipment — Test methods for laser
beam power (energy) density distribution
ISO 13695, Optics and photonics — Lasers and laser-related equipment — Test methods for the spectral
characteristics of lasers
ISO 13849-1, Safety of machinery — Safety-related parts of control systems — Part 1: General principles
for design
ISO 15367-1, Lasers and laser-related equipment — Test methods for determination of the shape of a laser
beam wavefront — Part 1: Terminology and fundamental aspects
ISO 15367-2, Lasers and laser-related equipment — Test methods for determination of the shape of a laser
beam wavefront — Part 2: Shack-Hartmann sensors
ISO 17526, Optics and optical instruments — Lasers and laser-related equipment — Lifetime of lasers
IEC 60529, Degrees of protection provided by enclosures (IP code)
IEC 60825-1, Safety of la
...