Flat products made of steels for pressure purposes - Part 1: General requirements

This European Standard specifies general technical delivery conditions for flat products for the construction of pressure equipment.
The general technical delivery conditions in EN 10021 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 97/23/EC are satisfied, needs to be done.

Flacherzeugnisse aus Druckbehälterstählen - Teil 1: Allgemeine Anforderungen

Diese Europäische Norm legt die allgemeinen technischen Lieferbedin¬gungen für im Druck¬behälterbau verwendete Flach¬erzeugnisse fest.
Es gelten ebenfalls die allgemeinen technischen Lieferbedingungen nach EN 10021.
ANMERKUNG   Nach Veröffentlichung dieser Norm im EU Amtsblatt (OJEU) unter der Richtlinie 97/23/EG ist die Annahme ihrer Konformität mit den grundlegenden Anforderungen (ESR) der Richtlinie 97/23/EG auf die technischen Daten von Werkstoffen in dieser Europäischen Norm (Teil 1 und der entsprechende Teil der Normenreihe) beschränkt, und es darf nicht angenommen werden, dass damit die Eignung des Werkstoffs für ein bestimmtes Ausrüstungsteil festgestellt ist. Folglich müssen die in dieser Werkstoffnorm angegebenen technischen Parameter im Hinblick auf die konstruktiven Anforderungen dieses bestimmten Ausrüstungsteils ermittelt werden, um damit zu verifizieren, dass den ESR der Richtlinie 97/23/EG entsprochen wird.

Produits plats en aciers pour appareils à pression - Prescriptions générales

La présente Norme européenne spécifie les conditions techniques générales de livraison des produits plats utilisés dans la construction des appareils à pression.
Les conditions techniques générales de livraison spécifiées par la norme EN 10021 s’appliquent également.
NOTE   Dès lors que la présente Norme européenne est publiée dans le Journal Officiel de l’Union européenne (JO) en lien avec la Directive 97/23/CE, la présomption de conformité avec les exigences essentielles de sécurité de la Directive 97/23/CE se limite aux données techniques relatives aux matériaux spécifiées dans la présente Norme européenne (partie 1 et autres parties concernées de la série) et ne suppose pas l’adéquation des matériaux avec un appareil en particulier. Par conséquent, il doit être procédé à l’évaluation des données techniques spécifiées dans la présente norme de matériaux par rapport aux exigences relatives à la conception de cet équipement spécifique, afin de vérifier que les exigences essentielles de sécurité de la Directive 97/23/CE sont satisfaites.

Ploščati jekleni izdelki za tlačne posode - 1. del: Splošne zahteve

General Information

Status
Withdrawn
Publication Date
04-Dec-2007
Withdrawal Date
21-Apr-2009
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
22-Apr-2009
Completion Date
22-Apr-2009

Relations

Buy Standard

Standard
EN 10028-1:2008
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flat products made of steels for pressure purposes General requirementsYHProduits plats en aciers pour appareils à pression - Prescriptions généralesFlacherzeugnisse aus Druckbehälterstählen - Teil 1: Allgemeine AnforderungenTa slovenski standard je istoveten z:EN 10028-1:2007SIST EN 10028-1:2008en,fr,de77.140.50SROL]GHONLFlat steel products and semi-products77.140.30Jekla za uporabo pod tlakomSteels for pressure purposesICS:SIST EN 10028-1:2001/A1:2003SIST EN 10028-1:20011DGRPHãþDSLOVENSKI
STANDARDSIST EN 10028-1:200801-februar-2008

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10028-1December 2007ICS 77.140.30; 77.140.50Supersedes EN 10028-1:2000
English VersionFlat products made of steels for pressure purposes - Part 1:General requirementsProduits plats en aciers pour appareils à pression -Prescriptions généralesFlacherzeugnisse aus Druckbehälterstählen - Teil 1:Allgemeine AnforderungenThis European Standard was approved by CEN on 21 October 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10028-1:2007: E

Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC.19 Bibliography.20

The clauses marked with a point (•) contain information relating to agreements which are to be made at the time of enquiry and order. The clauses marked by two points (••) contain information relating to agreements that may be made at the time of enquiry and order. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.

Tensile testing
Part 1: Method of test at ambient temperature EN 10002-5:1991, Metallic materials
Tensile testing
Part 5: Method of testing at elevated temperatures EN 10020:2000, Definition and classification of grades of steel EN 10021:2006, General technical delivery conditions for steel products EN 10028-2:2003, Flat products made of steels for pressure purposes
Part 2: Non-alloy and alloy steels with specified elevated temperature properties EN 10028-3:2003, Flat products made of steels for pressure purposes
Part 3: Weldable fine grain steels, normalized EN 10028-4:2003, Flat products made of steels for pressure purposes
Part 4: Nickel alloy steels with specified low temperature properties EN 10028-5:2003, Flat products made of steels for pressure purposes
Part 5: Weldable fine grain steels, thermomechanically rolled EN 10028-6:2003, Flat products made of steels for pressure purposes
Part 6: Weldable fine grain steels, quenched and tempered EN 10028-7:2007, Flat products made of steels for pressure purposes
Part 7: Stainless steels EN 10029, Hot rolled plates 3 mm thick or above
Tolerances on dimensions, shape and mass EN 10045-1:1990, Metallic materials
Charpy impact test
Part 1: Test method EN 10048, Hot rolled narrow steel strip
Tolerances on dimensions and shape EN 10051, Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels
Tolerances on dimensions and shape EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10079:2007, Definitions of steel products EN 10088-1:2005, Stainless steels
Part 1: List of stainless steels EN 10160, Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method)

Part 2: Plates and wide flats EN 10164:2004, Steel products with improved deformation properties perpendicular to the surface of the product
Technical delivery conditions EN 10168:2004, Steel products
Inspection documents
List of information and description EN 10204:2004, Metallic products
Types of inspection documents EN ISO 377, Steel and steel products
Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) EN ISO 2566-1, Steel
Conversion of elongation values
Part 1: Carbon and low alloy steels (ISO 2566-1:1984) EN ISO 2566-2, Steel
Conversion of elongation values
Part 2: Austenitic steels (ISO 2566-2:1984)
EN ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels
Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels
Corrosion test in media containing sulfuric acid (ISO 3651-2:1998) EN ISO 9445, Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut lengths
Tolerances on dimensions and form (ISO 9445:2002) EN ISO 14284, Steel and iron
Sampling and preparation of samples for the determination of chemical composition (ISO 14284:1996) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10020:2000, EN 10079:2007 and
EN 10052:1993 (but see 3.1 to 3.3) and the following apply. 3.1 normalizing rolling
rolling process in which the final deformation process is carried out in a certain temperature range leading to a material condition equivalent to that obtained after normalizing so that the specified values of the mechanical properties are retained even after normalizing NOTE The symbol for this delivery condition and for the normalized condit
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.