EN 10028-1:2000/A1:2002

SLOVENSKI STANDARD
SIST EN 10028-1:2001/A1:2003
01-april-2003
3ORãþDWLMHNOHQLL]GHONL]DWODþQHSRVRGHGHO6SORãQH]DKWHYH'RSROQLOR$
Flat products made of steels for pressure purposes - Part 1: General requirements
Flacherzeugnisse aus Druckbehälterstählen - Teil 1: Allgemeine Anforderungen
Produits plats en acier pour appareils a pression - Partie 1: Prescriptions générales
Ta slovenski standard je istoveten z: EN 10028-1:2000/A1:2002
ICS:
77.140.30
77.140.50
SIST EN 10028-1:2001/A1:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 10028-1:2000/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2002
ICS 77.140.30; 77.140.50
English version
Flat products made of steels for pressure purposes - Part 1:
General requirements
Produits plats en acier pour appareils à pression - Partie 1: Flacherzeugnisse aus Druckbehälterstählen - Teil 1:
Prescriptions générales Allgemeine Anforderungen
This amendment A1 modifies the European Standard EN 10028-1:2000; it was approved by CEN on 16 October 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10028-1:2000/A1:2002 E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 10028-1:2000/A1:2002 (E)
Foreword
This document EN 10028-1:2000/A1:2002 has been prepared by Technical Committee ECISS /TC 22 "Steels for
pressure purposes - Qualities", the secretariat of which is held by DIN.
This Amendment to the European Standard EN 10028-1:2000 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by May 2003, and conflicting national
standards shall be withdrawn at the latest by May 2003.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EU Directive(s).
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard : Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,
Sweden, Switzerland and the United Kingdom.
2

---------------------- Page: 3 ----------------------

EN 10028-1:2000/A1:2002 (E)
5 C
...