EN 10028-5:2017

SLOVENSKI STANDARD
01-oktober-2017
1DGRPHãþD
SIST EN 10028-5:2009
]UQDWDMHNOD3ORãþDWLMHNOHQLL]GHONL]DWODþQHSRVRGHGHO9DULYDGUREQR
WHUPRPHKDQVNRYDOMDQD
Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels,
thermomechanically rolled
Flacherzeugnisse aus Druckbehälterstählen - Teil 5: Schweißgeeignete
Feinkornbaustähle, thermomechanisch gewalzt
Produits plats en acier pour appareils à pression - Partie 5: Aciers soudable à grains fins,
laminés thermomécaniquement
Ta slovenski standard je istoveten z: EN 10028-5:2017
ICS:
77.140.30 Jekla za uporabo pod tlakom Steels for pressure purposes
77.140.50 3ORãþDWLMHNOHQLL]GHONLLQ Flat steel products and semi-
SROL]GHONL products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 10028-5
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2017
EUROPÄISCHE NORM
ICS 77.140.30; 77.140.50 Supersedes EN 10028-5:2009
English Version
Flat products made of steels for pressure purposes - Part
5: Weldable fine grain steels, thermomechanically rolled
Produits plats en acier pour appareils à pression - Flacherzeugnisse aus Druckbehälterstählen - Teil 5:
Partie 5 : Aciers soudable à grains fins, laminés Schweißgeeignete Feinkornbaustähle,
thermomécaniquement thermomechanisch gewalzt
This European Standard was approved by CEN on 7 May 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10028-5:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Tolerances on dimensions . 4
5 Calculation of mass . 4
6 Classification and designation . 5
6.1 Classification . 5
6.2 Designation . 5
7 Information to be supplied by the purchaser . 5
7.1 Mandatory information . 5
7.2 Options . 5
7.3 Example for ordering. 5
8 Requirements . 6
8.1 Steelmaking process . 6
8.2 Delivery condition . 6
8.3 Chemical composition . 6
8.4 Mechanical properties . 6
8.5 Surface condition . 6
8.6 Internal soundness . 6
9 Inspection . 6
9.1 Types of inspection and inspection documents . 6
9.2 Tests to be carried out . 6
9.3 Retests, sorting and reprocessing . 6
10 Sampling . 7
11 Test methods . 7
12 Marking . 7
Annex A (informative) Information on weldability . 11
Annex B (informative) Changes to the previous version EN 10028-5:2009 . 12
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2014/68/EU . 13
European foreword
This document (EN 10028-5:2017) has been prepared by Technical Committee ECISS/TC 107 “Steels
for pressure purposes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2018 and conflicting national standards shall
be withdrawn at the latest by January 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 10028-5:2009.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of Directive 2014/68/EU.
For relationship with Directive 2014/68/EU, see informative Annex ZA, which is an integral part of this
document.
A list of changes between this document and the previous version can be found in Annex B.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
1 Scope
This European Standard specifies the requirements for flat products for pressure equipment made of
weldable fine grain thermomechanically rolled steels as specified in Table 1.
The steels are not suitable for hot forming.
NOTE 1 At the time of publication of this European Standard, no sufficient data for the standardization of the
elevated temperature properties of these steels was available.
If their use at such temperatures is intended the conditions for this should be specially agreed between
the interested parties.
The requirements of EN 10028-1:2017 also apply.
NOTE 2 Once this European Standard is published in the EU Official Journal (OJEU) under Directive
2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is
limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series)
and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of
the technical data stated in this material standard against the design requirements of this specific item of
equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 1011-1:2009, Welding — Recommendations for welding of metallic materials — Part 1: General
guidance for arc welding
EN 1011-2:2001, Welding — Recommendations for welding of metallic materials — Part 2: Arc welding of
ferritic steels
EN 10020:2000, Definition and classification of grades of steel
EN 10028-1:2017, Flat products made of steels for pressure purposes — Part 1: General requirements
EN 10204:2004, Metallic products — Types of inspection documents
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 10028-1:2017 apply.
4 Tolerances on dimensions
See EN 10028-1:2017.
5 Calculation of mass
See EN 10028-1:2017.
6 Classification and designation
6.1 Classification
6.1.1 This European Standard covers the steel grades given in Table 1 in three qualities:
a) the basic series (P.M);
b) series with low temperature properties down to −40 °C (P.ML1);
c) series with low temperature properties down to −50 °C (P.ML2).
6.1.2 In accordance with EN 10020:2000 all the steels specified in this document are alloy special
steels.
6.2 Designation
See EN 10028-1:2017.
7 Information to be supplied by the purchaser
7.1 Mandatory information
See EN 10028-1:2017.
7.2 Options
A number of options are specified in this document and listed below. Additionally the relevant options
of EN 10028-1:2017 apply. If the purchaser does not indicate a wish to implement any of these options
at the time of enquiry and order, the products shall be supplied in accordance with the basic
specification (see also EN 10028-1:2017):
1) providing data on suitable welding conditions (see 8.2.2);
2) maximum carbon equivalent (see 8.3.3);
3) specification of a minimum impact energy of 40 J (see 8.4 and Table 5);
4) mid thickness test pieces for the impact test (see Clause 10).
7.3 Example for ordering
10 plates with nominal dimensions, thickness = 50 mm, width = 2 000 mm, length = 10 000 mm, made
of a steel grade with the name P355ML2 and the number 1.8833 as specified in EN 10028-5, inspection
certificate 3.1 as specified in EN 10204:
10 plates – 50 × 2 000 × 10 000 – EN 10028-5 – P355ML2 – Inspection certificate 3.1
or
10 plates – 50 × 2 000 × 10 000 – EN 10028-5 – 1.8833 – Inspection certificate 3.1
8 Requirements
8.1 Steelmaking process
See EN 10028-1:2017.
8.2 Delivery condition
8.2.1 The products covered by this European Standard shall be supplied in the thermomechanically
rolled condition.
8.2.2 Information on weldability are given in Annex A of this standard.
8.3 Chemical composition
8.3.1 The requirements of Table 1 apply for the chemical composition according to the cast analysis.
8.3.2 The product analysis shall not deviate from the specified values for the cast analysis as specified
in Table 1 by more than the values given in Table 2.
8.3.3 A maximum value for the carbon equivalent in accordance with Table 3 may be agreed at time of
enquiry and order.
8.4 Mechanical properties
The values given in Tables 4 and 5 (see also EN 10028-1:2017 and Clause 10) shall apply.
Optionally, a minimum impact energy value of 40 J may be specified for temperatures where lower
minimum values are specified (see Table 5, footnote a).
8.5 Surface condition
See EN 10028-1:2017.
8.6 Internal soundness
See EN 10028-1:2017.
9 Inspection
9.1 Types of inspecti
...