EN 10028-7:2016
(Main)Flat products made of steels for pressure purposes - Part 7: Stainless steels
Flat products made of steels for pressure purposes - Part 7: Stainless steels
This European Standard specifies requirements for flat products for pressure purposes made of stainless steels, including austenitic creep resisting steels, in thicknesses as indicated in Tables 7 to 10.
The requirements of EN 10028-1:2007+A1:2009 also apply.
NOTE 1 The steel grades covered by this European Standard have been selected from EN 10088-1.
NOTE 2 Once this European Standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard (Part 1 and Part 7) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done.
Flacherzeugnisse aus Druckbehälterstählen - Teil 7: Nichtrostende Stähle
Diese Europäische Norm enthält die Anforderungen an Flacherzeugnisse für Druckbehälter aus nichtrostenden Stählen, einschließlich von austenitischen hochwarmfesten Stählen, mit den in den Tabellen 7 bis 10 angegebenen Dicken.
Zusätzlich gelten die Angaben in EN 10028-1.
ANMERKUNG 1 Die Stahlsorten nach dieser Europäischen Norm wurden aus EN 10088-1 ausgewählt.
ANMERKUNG 2 Nach Veröffentlichung dieser Europäischen Norm im EU-Amtsblatt (OJEU) ist die Annahme ihrer Konformität mit den grundlegenden Anforderungen (ESR) der Richtlinie 2014/68/EU auf die technischen Daten von Werkstoffen in dieser Europäischen Norm (Teil 1 und Teil 7) beschränkt, und es darf nicht angenommen werden, dass damit die Eignung des Werkstoffs für ein bestimmtes Ausrüstungsteil festgestellt ist. Folglich müssen die in dieser Werkstoffnorm angegebenen technischen Parameter im Hinblick auf die konstruktiven Anforderungen dieses bestimmten Ausrüstungsteils ermittelt werden, um zu verifizieren, dass den ESR der Druckgeräterichtlinie 2014/68/EU entsprochen wird.
Produits plats en aciers pour appareils à pression - Partie 7: Aciers inoxydables
La présente Norme européenne spécifie les prescriptions relatives aux produits plats pour appareils à pression en aciers inoxydables, y compris les aciers austénitiques résistants au fluage dans les épaisseurs indiquées aux Tableaux 7 à 10.
Les prescriptions de l'EN 10028-1+A1 :2009 s'appliquent également.
NOTE 1 Les nuances d’acier comprises dans cette norme ont été sélectionnées à partir de l’EN 10088-1.
NOTE 2 Une fois la norme européenne publiée dans le Journal Officiel de l’Union Européenne (JOUE), sous la Directive 97/231 EC, la présomption de conformité aux exigences essentielles de sécurité (ESRS) de la Directive 97/23/EC est limitée aux données techniques des matériaux de cette norme européenne (parties 1 à 7) et ne présume pas l’adéquation du matériau à un équipement spécifique. Par conséquent, l’évaluation des données techniques indiquées par cette norme de matériaux à l’égard des exigences de conceptions d’équipements spécifiques, afin de vérifier que les (ESRS) de la Directives des équipements sous pression sont satisfaites, doit être faite.
Ploščati jekleni izdelki za tlačne posode - 7. del: Nerjavna jekla
Ta evropski standard določa zahteve za debelino ploščatih izdelkov za tlačne posode iz nerjavnega jekla, vključno z avstentnim jeklom, ki je odporno proti lezenju, kot je navedeno v preglednicah od 7 do 10.
Uporabljajo se tudi zahteve standarda EN 10028-1:2007+A1:2009.
OPOMBA 1: razredi jekla, ki so zajeti v tem evropskem standardu, so bili izbrani iz standarda EN 10088-1.
OPOMBA 2: ko bo ta evropski standard objavljen v Uradnem listu Evropske unije (OJEU) v okviru Direktive 97/23/ES, bodo zagotovila o skladnosti z osnovnimi varnostnimi zahtevami (ESR) Direktive 97/23/ES omejena na tehnične podatke o materialih, navedene v tem evropskem standardu (dela 1 in 7), standard pa ne bo zagotavljal ustreznosti materiala za določen element opreme. Zato bo potrebno oceniti tehnične podatke, podane v tem standardu za materiale, glede na zahteve zasnove določenega elementa opreme, da se zagotovi, da so osnovne varnostne zahteve Direktive o tlačni opremi spoštovane.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.DFlacherzeugnisse aus Druckbehälterstählen - Teil 7: Nichtrostende StähleProduits plats en aciers pour appareils à pression - Partie 7: Aciers inoxydablesFlat products made of steels for pressure purposes - Part 7: Stainless steels77.140.50SROL]GHONLFlat steel products and semi-products77.140.30Jekla za uporabo pod tlakomSteels for pressure purposes77.140.20Visokokakovostna jeklaStainless steelsICS:Ta slovenski standard je istoveten z:EN 10028-7:2016SIST EN 10028-7:2016en,fr,de01-september-2016SIST EN 10028-7:2016SLOVENSKI
STANDARDSIST EN 10028-7:20081DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10028-7
July 2016 ICS 77.140.30; 77.140.50 Supersedes EN 10028-7:2007
English Version
Flat products made of steels for pressure purposes - Part 7: Stainless steels
Produits plats en aciers pour appareils à pression - Partie 7: Aciers inoxydables
Flacherzeugnisse aus Druckbehälterstählen - Teil 7: Nichtrostende Stähle This European Standard was approved by CEN on 15 April 2016.
This European Standard was corrected and reissued by the CEN-CENELEC Management Centre on 2016-07-27.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10028-7:2016 E SIST EN 10028-7:2016
Page European foreword . 4 Introduction . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 6 4 Tolerances on dimensions . 6 5 Calculation of mass . 7 6 Classification and designation . 7 7 Information to be supplied by the purchaser . 7 7.1 Mandatory information . 7 7.2 Options . 7 7.3 Example for ordering. 7 8 Requirements . 7 8.1 Steelmaking process . 7 8.2 Delivery condition . 7 8.3 Chemical composition and chemical corrosion properties . 7 8.4 Mechanical properties . 8 8.5 Surface condition . 8 8.6 Internal soundness . 8 8.7 Physical properties . 8 8.8 Weldability . 8 9 Inspection . 9 9.1 Types of inspection and inspection documents . 9 9.2 Tests to be carried out . 9 9.3 Re-tests, sorting and reprocessing . 9 10 Sampling . 9 10.1 Frequency of testing. 9 10.2 Selection and preparation of samples and test pieces . 9 11 Test methods . 9 12 Marking . 9 Annex A (informative)
Guidelines for further treatment (including heat treatment in fabrication) . 34 Annex B (informative)
Post weld heat treatment . 39 Annex C (informative)
Preliminary reference data for the tensile strength of austenitic-ferritic steels at elevated temperatures . 41 Annex D (informative)
Reference data of strength values for 1 % (plastic) creep strain and creep rupture . 42 Annex E (informative)
Reference data on mechanical properties of austenitic steels at room temperature and at
low temperatures . 51 SIST EN 10028-7:2016
Significant changes to the version EN 10028-7:2007 . 52 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of Directive 2014/68/EU . 53 Bibliography . 54
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.