EN 10028-1:2007+A1:2009
(Main + Amendment)Flat products made of steels for pressure purposes - Part 1: General requirements
Flat products made of steels for pressure purposes - Part 1: General requirements
This European Standard specifies general technical delivery conditions for flat products for the construction of pressure equipment.
The general technical delivery conditions in EN 10021 also apply.
NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 97/23/EC are satisfied, needs to be done.
Flacherzeugnisse aus Druckbehälterstählen - Teil 1: Allgemeine Anforderungen
Diese Europäische Norm legt die allgemeinen technischen Lieferbedingungen für im Druckbehälterbau
verwendete Flacherzeugnisse fest.
Es gelten ebenfalls die allgemeinen technischen Lieferbedingungen nach EN 10021.
ANMERKUNG Nach Veröffentlichung dieser Norm im EU-Amtsblatt (OJEU) unter der Richtlinie 97/23/EG ist die
Annahme ihrer Konformität mit den grundlegenden Anforderungen (ESR) der Richtlinie 97/23/EG auf die technischen
Daten von Werkstoffen in dieser Europäischen Norm (Teil 1 und der entsprechende Teil der Normenreihe) beschränkt,
und es darf nicht angenommen werden, dass damit die Eignung des Werkstoffs für ein bestimmtes Ausrüstungsteil
festgestellt ist. Folglich müssen die in dieser Werkstoffnorm angegebenen technischen Parameter im Hinblick auf die
konstruktiven Anforderungen dieses bestimmten Ausrüstungsteils ermittelt werden, um damit zu verifizieren, dass den
ESR der Richtlinie 97/23/EG entsprochen wird.
Produits plats en acier pour appareils à pression - Partie 1: Prescriptions générales
La présente Norme européenne spécifie les conditions techniques générales de livraison des produits plats utilisés
dans la construction des appareils à pression.
Les conditions techniques générales de livraison spécifiées par la norme EN 10021 s’appliquent également.
NOTE Dès lors que la présente Norme européenne est publiée dans le Journal Officiel de l’Union européenne (JO) en lien
avec la Directive 97/23/CE, la présomption de conformité avec les exigences essentielles de sécurité de la Directive 97/23/CE
se limite aux données techniques relatives aux matériaux spécifiées dans la présente Norme européenne (partie 1 et autres
parties concernées de la série) et ne suppose pas l’adéquation des matériaux avec un appareil en particulier. Par conséquent,
il doit être procédé à l’évaluation des données techniques spécifiées dans la présente norme de matériaux par rapport aux
exigences relatives à la conception de cet équipement spécifique, afin de vérifier que les exigences essentielles de sécurité
de la Directive 97/23/CE sont satisfaites.
Ploščati jekleni izdelki za tlačne posode - 1. del: Splošne zahteve
Ta evropski standard opredeljuje splošne tehnične pogoje dostave ploščatih izdelkov za konstrukcijo tlačne opreme. Prav tako veljajo splošni tehnični pogoji dostave v EN 10021.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.YHFlacherzeugnisse aus Druckbehälterstählen - Teil 1: Allgemeine AnforderungenProduits plats en acier pour appareils à pression - Partie 1: Prescriptions généralesFlat products made of steels for pressure purposes - Part 1: General requirements77.140.50SROL]GHONLFlat steel products and semi-products77.140.30Jekla za uporabo pod tlakomSteels for pressure purposesICS:Ta slovenski standard je istoveten z:EN 10028-1:2007+A1:2009SIST EN 10028-1:2008+A1:2009en,fr,de01-julij-2009SIST EN 10028-1:2008+A1:2009SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10028-1:2007+A1
April 2009 ICS 77.140.30; 77.140.50 Supersedes EN 10028-1:2007English Version
Flat products made of steels for pressure purposes - Part 1: General requirements
Produits plats en acier pour appareils à pression - Partie 1: Prescriptions générales
Flacherzeugnisse aus Druckbehälterstählen - Teil 1: Allgemeine Anforderungen This European Standard was approved by CEN on 21 October 2007 and includes Amendment 1 approved by CEN on 14 March 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10028-1:2007+A1:2009: ESIST EN 10028-1:2008+A1:2009
Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC . 19 Bibliography . 20
The clauses marked with a point (•) contain information relating to agreements which are to be made at the time of enquiry and order. The clauses marked by two points (••) contain information relating to agreements that may be made at the time of enquiry and order. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
Tensile testing
Part 1: Method of test at ambient temperature EN 10002-5:1991, Metallic materials
Tensile testing
Part 5: Method of testing at elevated temperatures EN 10020:2000, Definition and classification of grades of steel EN 10021:2006, General technical delivery conditions for steel products EN 10028-2:2003, Flat products made of steels for pressure purposes
Part 2: Non-alloy and alloy steels with specified elevated temperature properties EN 10028-3:2003, Flat products made of steels for pressure purposes
Part 3: Weldable fine grain steels, normalized EN 10028-4:2003, Flat products made of steels for pressure purposes
Part 4: Nickel alloy steels with specified low temperature properties EN 10028-5:2003, Flat products made of steels for pressure purposes
Part 5: Weldable fine grain steels, thermomechanically rolled EN 10028-6:2003, Flat products made of steels for pressure purposes
Part 6: Weldable fine grain steels, quenched and tempered EN 10028-7:2007, Flat products made of steels for pressure purposes
Part 7: Stainless steels EN 10029, Hot rolled plates 3 mm thick or above
Tolerances on dimensions, shape and mass EN 10045-1:1990, Metallic materials
Charpy impact test
Part 1: Test method EN 10048, Hot rolled narrow steel strip
Tolerances on dimensions and shape EN 10051, Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels
Tolerances on dimensions and shape EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10079:2007, Definitions of steel products EN 10088-1:2005, Stainless steels
Part 1: List of stainless steels EN 10160, Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) SIST EN 10028-1:2008+A1:2009
Part 2: Plates and wide flats EN 10164:2004, Steel products with improved deformation properties perpendicular to the surface of the product
Technical delivery conditions EN 10168:2004, Steel products
Inspection documents
List of information and description EN 10204:2004, Metallic products
Types of inspection documents EN ISO 377, Steel and steel products
Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) EN ISO 2566-1, Steel
Conversion of elongation values
Part 1: Carbon and low alloy steels (ISO 2566-1:1984) EN ISO 2566-2, Steel
Conversion of elongation values
Part 2: Austenitic steels (ISO 2566-2:1984)
EN ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels
Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels
Corrosion test in media containing sulfuric acid (ISO 3651-2:1998) EN ISO 9445, Continuously cold-rolled stai
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.