2015/1095 - Commission Regulation (EU) 2015/1095 of 5 May 2015 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for professional refrigerated storage cabinets, blast cabinets, condensing units and process chillers

This Standard specifies methods for the measurement of energy consumption, water consumption and ice production capacity of ice makers and harvested ice characteristics for commercial use.
This Standard does not apply to:
- ice makers intended to be incorporated in appliances for household use;
- ice makers with remote condensing units.

This document specifies methods for the measurement of energy consumption, water consumption, ice production capacity and the harvested ice characteristics of ice makers with built-in condensing units for commercial use.
This document does not apply to:
—    ice makers intended to be incorporated in appliances for household use;
—    ice makers with remote condensing units.

This document is applicable to air conditioners, heat pumps and liquid chilling packages, including comfort and process chillers. It applies to factory made units defined in EN 14511-1, except single duct, double duct, control cabinet and close control units. It also covers direct exchange-to-water(brine) heat pumps (DX-to-water(brine)) as defined in EN 15879-1.
This document also applies to hybrid units as defined in this standard.
This document specifies the temperatures, part load conditions and the calculation methods for the determination of seasonal energy efficiency SEER and SEERon, seasonal space cooling energy efficiency ηs,c, seasonal coefficient of performance SCOP, SCOPon and SCOPnet, seasonal space heating energy efficiency ηs,h and seasonal energy performance ratio SEPR.
Such calculation methods can be based on calculated or measured values.
In case of measured values, this document specifies the test methods for determination of capacities, EER and COP values during active mode at part load conditions. It also establishes test methods for power input during thermostat-off mode, standby mode, off mode and crankcase heater mode.
NOTE 1   The word "unit" is used instead of the full terms of the products.
NOTE 2   The word "heating" is used to refer to space heating.

1.1 The scope of EN 14511-1:2022 is applicable.
1.2 This document specifies the test methods for the rating and performance of air conditioners, liquid
chilling packages and heat pumps using either air, water or brine as heat transfer media, with electrically
driven compressors when used for space heating and cooling. These test methods also apply for the rating
and performance of process chillers.
It also specifies the method of testing and reporting for heat recovery capacities, system reduced
capacities and the capacity of individual indoor units of multisplit systems, where applicable.
This document also makes possible to rate multisplit and modular heat recovery multisplit systems by
rating separately the indoor and outdoor units.

1.1   The scope of EN 14511 1 is applicable.
1.2   This European Standard specifies the test conditions for the rating of air conditioners, liquid chilling packages and heat pumps, using either, air, water or brine as heat transfer media, with electrically driven compressors when used for space heating and/or cooling. The standard also specifies the test conditions for the rating of air-cooled and water(brine)-cooled process chillers.
1.3   This European Standard specifies the conditions for which performance data is to be declared for single duct and double duct units for compliance to the Ecodesign Regulation 206/2012 and Energy Labelling Regulation 626/2011.

1.1   The scope of EN 14511-1:2022 is applicable.
1.2   This document specifies the test conditions for the rating of air conditioners, liquid chilling packages and heat pumps, using either, air, water or brine as heat transfer media, with electrically driven compressors when used for space heating and/or cooling. The document also specifies the test conditions for the rating of air-cooled and water(brine)-cooled process chillers.
1.3   This document specifies the conditions for which performance data are to be declared for single duct and double duct units for compliance to the Ecodesign Regulation 206/2012 and Energy Labelling Regulation 626/2011.

1.1   The scope of EN 14511-1:2022 is applicable.
1.2   This document specifies the test methods for the rating and performance of air conditioners, liquid chilling packages and heat pumps using either air, water or brine as heat transfer media, with electrically driven compressors when used for space heating and cooling. These test methods also apply for the rating and performance of process chillers.
It also specifies the method of testing and reporting for heat recovery capacities, system reduced capacities and the capacity of individual indoor units of multisplit systems, where applicable.
This document also makes possible to rate multisplit and modular heat recovery multisplit systems by rating separately the indoor and outdoor units.

This European Standard covers air conditioners, heat pumps and liquid chilling packages, including comfort and process chillers. It applies to factory made units defined in EN 14511-1, except single duct, double duct, control cabinet and close control units. It also covers direct expansion-to-water(brine) heat pumps (DX-to-water) as defined in EN 15879-1.
This European Standard also covers hybrid heat pumps as defined in this standard.
This European Standard gives the temperatures and part load conditions and the calculation methods for the determination of seasonal energy efficiency SEER and SEERon, seasonal space cooling energy efficiency ηs,c seasonal coefficient of performance SCOP, SCOPon and SCOPnet, and seasonal space heating energy efficiency ηs,h and seasonal energy performance ratio SEPR.
Such calculation methods may be based on calculated or measured values.
In case of measured values, this European Standard covers the test methods for determination of capacities, EER and COP values during active mode at part load conditions. It also covers test methods for electric power consumption during thermostat-off mode, standby mode, off-mode and crankcase heater mode.
NOTE 1 The word "unit" is used instead of the full terms of the products.
NOTE 2 The word "cooling" is used to refer to both space cooling and process cooling.
NOTE 3 The word "heating" is used to refer to space heating.

This document specifies the requirements for the verification of performance and energy consumption of blast cabinets for professional use in commercial kitchens, hospitals, canteens, institutional catering and similar professional areas.
The appliances covered by this document are intended to rapidly cool down hot foodstuffs up to a load capacity of 300 kg.
This document applies to:
—    blast chillers;
—    blast freezers;
—    multi-use blast chillers/freezers.
The following appliances are not covered:
—    roll-in cabinet;
—    pass-through cabinet;
—    cabinets with remote condensing unit;
—    cabinets with water cooled condenser;
—    blast chilling and freezing tunnels;
—    continuous blast-chilling and blast-freezing equipment;
—    bakery combined freezing and storage units.

This Standard specifies the requirements for the verification of performance and energy consumption of blast cabinets for professional use in commercial kitchens, hospitals, canteens, institutional catering and similar professional areas.
The appliances covered by this Standard are intended to rapidly cool down hot foodstuffs up to a load capacity of 300 kg.

This European Standard specifies the rating conditions, tolerances and presentation of manufacturer's performance data for condensing units for refrigeration with compressors of the positive-displacement type. These include single stage compressors and single and two stage compressors having an integrated means of fluid sub cooling. This is required so that a comparison of different condensing units can be made. The data relate to the refrigerating capacity and power absorbed and include requirements for part-load performance where applicable.

This European Standard specifies the rating conditions, tolerances and presentation of manufacturer's performance data for condensing units for refrigeration with compressors of the positive-displacement type. These include single stage compressors and single and two stage compressors having an integrated means of fluid sub cooling. This is required so that a comparison of different condensing units can be made. The data relate to the refrigerating capacity and power absorbed and include requirements for part-load performance where applicable.

This document specifies requirements for the verification of performance and energy consumption of refrigerated storage cabinets and counters for professional use in commercial kitchens, hospitals, canteens, preparation areas of bars, bakeries, gelateria, institutional catering and similar professional areas.
The products covered in this document are intended to store foodstuffs. It specifies test conditions and methods for checking that the requirements have been satisfied, as well as classification of the cabinets and counters, their marking and the list of their characteristics to be declared by the manufacturer.
It is not applicable to:
—          refrigerated cabinets used in the direct sale of foodstuffs;
—          cabinets that carry out food processing and not just storage function (e.g. bakery cabinets that chill, heat and humidify);
—          cabinets with water cooled condenser;
—          appliances with remote condensing unit;
—          appliances with open top tables and saladettes for preparation or storage of foodstuffs;
—          cabinets specifically intended for storage of specific foodstuffs (i.e. fresh meat, fresh fish, etc.) operating at a temperature different from those specified in Table 1;
—          chest freezers;
—          appliances intended for short time /intermittent normal operation during the full day;
—          built-in cabinets;
—          roll-in cabinets;
—          pass-through cabinets;
—          ice cream freezers.

This Standard specifies requirements for the verification of performance including energy consumption of refrigerated storage cabinets and counters for professional use in commercial kitchens, hospitals, canteens, preparation areas of bars, bakeries, gelateria, institutional catering and similar professional areas.
The products covered in this Standard are intended to store foodstuffs. It specifies test conditions and methods for checking that the requirements have been satisfied, as well as classification of the cabinets and counters, their marking and the list of their characteristics to be declared by the manufacturer.

This standard specifies the requirements for the construction, characteristics, performance including energy consumption of blast cabinet for professional used in commercial kitchens, hospitals, canteens, institutional catering and similar professional areas.
The appliances covered by this standard are intended to rapidly cool down hot foodstuffs up to a load capacity of 300 kg.
This standard applies to:
-   blast chillers;
-   blast freezers;
-   multi-use blast chillers/freezers.
The following appliances are not covered:
-   roll-in cabinet;
-   pass-through cabinet;
-   cabinets with remote condensing unit;
NOTE   Specific requirements for roll-in cabinet, pass-through cabinet and cabinets with remote condensing unit are under discussion.
-   cabinets with water cooled condenser;
-   blast chilling and freezing tunnels;
-   continuous blast-chilling and blast-freezing equipment;
-   bakery combined freezing and storage units.

1.1   The scope of EN 14511-1:2022 is applicable.
1.2   This document specifies the test conditions for the rating of air conditioners, liquid chilling packages and heat pumps, using either, air, water or brine as heat transfer media, with electrically driven compressors when used for space heating and/or cooling. The document also specifies the test conditions for the rating of air-cooled and water(brine)-cooled process chillers.
1.3   This document specifies the conditions for which performance data are to be declared for single duct and double duct units for compliance to the Ecodesign Regulation 206/2012 and Energy Labelling Regulation 626/2011.

This document is applicable to air conditioners, heat pumps and liquid chilling packages, including comfort and process chillers. It applies to factory made units defined in EN 14511-1, except single duct, double duct, control cabinet and close control units. It also covers direct exchange-to-water(brine) heat pumps (DX-to-water(brine)) as defined in EN 15879-1.
This document also applies to hybrid units as defined in this standard.
This document specifies the temperatures, part load conditions and the calculation methods for the determination of seasonal energy efficiency SEER and SEERon, seasonal space cooling energy efficiency ηs,c, seasonal coefficient of performance SCOP, SCOPon and SCOPnet, seasonal space heating energy efficiency ηs,h and seasonal energy performance ratio SEPR.
Such calculation methods can be based on calculated or measured values.
In case of measured values, this document specifies the test methods for determination of capacities, EER and COP values during active mode at part load conditions. It also establishes test methods for power input during thermostat-off mode, standby mode, off mode and crankcase heater mode.
NOTE 1   The word "unit" is used instead of the full terms of the products.
NOTE 2   The word "heating" is used to refer to space heating.

1.1   The scope of EN 14511-1:2022 is applicable.
1.2   This document specifies the test conditions for the rating of air conditioners, liquid chilling packages and heat pumps, using either, air, water or brine as heat transfer media, with electrically driven compressors when used for space heating and/or cooling. The document also specifies the test conditions for the rating of air-cooled and water(brine)-cooled process chillers.
1.3   This document specifies the conditions for which performance data are to be declared for single duct and double duct units for compliance to the Ecodesign Regulation 206/2012 and Energy Labelling Regulation 626/2011.

This document is applicable to air conditioners, heat pumps and liquid chilling packages, including comfort and process chillers. It applies to factory made units defined in EN 14511-1, except single duct, double duct, control cabinet and close control units. It also covers direct exchange-to-water(brine) heat pumps (DX-to-water(brine)) as defined in EN 15879-1.
This document also applies to hybrid units as defined in this standard.
This document specifies the temperatures, part load conditions and the calculation methods for the determination of seasonal energy efficiency SEER and SEERon, seasonal space cooling energy efficiency ηs,c, seasonal coefficient of performance SCOP, SCOPon and SCOPnet, seasonal space heating energy efficiency ηs,h and seasonal energy performance ratio SEPR.
Such calculation methods can be based on calculated or measured values.
In case of measured values, this document specifies the test methods for determination of capacities, EER and COP values during active mode at part load conditions. It also establishes test methods for power input during thermostat-off mode, standby mode, off mode and crankcase heater mode.
NOTE 1   The word "unit" is used instead of the full terms of the products.
NOTE 2   The word "heating" is used to refer to space heating.

This European Standard specifies the rating conditions, tolerances and presentation of manufacturer's performance data for condensing units for refrigeration with compressors of the positive-displacement type. These include single stage compressors and single and two stage compressors having an integrated means of fluid sub cooling. This is required so that a comparison of different condensing units can be made. The data relate to the refrigerating capacity and power absorbed and include requirements for part-load performance where applicable.

This European Standard specifies the rating conditions, tolerances and presentation of manufacturer's performance data for condensing units for refrigeration with compressors of the positive-displacement type. These include single stage compressors and single and two stage compressors having an integrated means of fluid sub cooling. This is required so that a comparison of different condensing units can be made. The data relate to the refrigerating capacity and power absorbed and include requirements for part-load performance where applicable.

1.1   The scope of EN 14511 1 is applicable.
1.2   This European Standard specifies the test conditions for the rating of air conditioners, liquid chilling packages and heat pumps, using either, air, water or brine as heat transfer media, with electrically driven compressors when used for space heating and/or cooling. The standard also specifies the test conditions for the rating of air-cooled and water(brine)-cooled process chillers.
1.3   This European Standard specifies the conditions for which performance data is to be declared for single duct and double duct units for compliance to the Ecodesign Regulation 206/2012 and Energy Labelling Regulation 626/2011.

This European Standard covers air conditioners, heat pumps and liquid chilling packages, including comfort and process chillers. It applies to factory made units defined in EN 14511-1, except single duct, double duct, control cabinet and close control units. It also covers direct expansion-to-water(brine) heat pumps (DX-to-water) as defined in EN 15879-1.
This European Standard also covers hybrid heat pumps as defined in this standard.
This European Standard gives the temperatures and part load conditions and the calculation methods for the determination of seasonal energy efficiency SEER and SEERon, seasonal space cooling energy efficiency ηs,c seasonal coefficient of performance SCOP, SCOPon and SCOPnet, and seasonal space heating energy efficiency ηs,h and seasonal energy performance ratio SEPR.
Such calculation methods may be based on calculated or measured values.
In case of measured values, this European Standard covers the test methods for determination of capacities, EER and COP values during active mode at part load conditions. It also covers test methods for electric power consumption during thermostat-off mode, standby mode, off-mode and crankcase heater mode.
NOTE 1 The word "unit" is used instead of the full terms of the products.
NOTE 2 The word "cooling" is used to refer to both space cooling and process cooling.
NOTE 3 The word "heating" is used to refer to space heating.

This European Standard covers air conditioners, heat pumps and liquid chilling packages, including comfort and process chillers. It applies to factory made units defined in EN 14511-1, except single duct, double duct, control cabinet and close control units. It also covers direct expansion-to-water(brine) heat pumps (DX-to-water) as defined in EN 15879-1.
This European Standard also covers hybrid heat pumps as defined in this standard.
This European Standard gives the temperatures and part load conditions and the calculation methods for the determination of seasonal energy efficiency SEER and SEERon, seasonal space cooling energy efficiency ηs,c seasonal coefficient of performance SCOP, SCOPon and SCOPnet, and seasonal space heating energy efficiency ηs,h and seasonal energy performance ratio SEPR.
Such calculation methods may be based on calculated or measured values.
In case of measured values, this European Standard covers the test methods for determination of capacities, EER and COP values during active mode at part load conditions. It also covers test methods for electric power consumption during thermostat-off mode, standby mode, off-mode and crankcase heater mode.
NOTE 1 The word "unit" is used instead of the full terms of the products.
NOTE 2 The word "cooling" is used to refer to both space cooling and process cooling.
NOTE 3 The word "heating" is used to refer to space heating.

This European Standard specifies the requirements for the construction, characteristics, performance including energy consumption of blast cabinet for professional used in commercial kitchens, hospitals, canteens, institutional catering and similar professional areas.
The appliances covered by this European Standard are intended to rapidly cool down hot foodstuffs up to a load capacity of 300 kg.
This European Standard applies to:
-   blast chillers;
-   blast freezers;
-   multi-use blast chillers/freezers.
The following appliances are not covered:
-   roll-in cabinet;
-   pass-through cabinet;
-   cabinets with remote condensing unit;
NOTE   Specific requirements for roll-in cabinets, pass-through cabinets and cabinets with remote condensing unit are under discussion.
-   cabinets with water cooled condenser;
-   blast chilling and freezing tunnels;
-   continuous blast-chilling and blast-freezing equipment;
-   bakery combined freezing and storage units.

This European Standard specifies the rating conditions, tolerances and presentation of manufacturer's performance data for condensing units for refrigeration with compressors of the positive-displacement type. These include single stage compressors and single and two stage compressors having an integrated means of fluid sub cooling. This is required so that a comparison of different condensing units can be made. The data relate to the refrigerating capacity and power absorbed and include requirements for part-load performance where applicable.

This European Standard specifies the rating conditions, tolerances and presentation of manufacturer's performance data for condensing units for refrigeration with compressors of the positive-displacement type. These include single stage compressors and single and two stage compressors having an integrated means of fluid sub cooling. This is required so that a comparison of different condensing units can be made. The data relate to the refrigerating capacity and power absorbed and include requirements for part-load performance where applicable.

This standard is intended to set up requirements and test methods for measuring and recording the energy used by commercial refrigerated cabinets and counters for use in commercial kitchens.

This European Standard specifies requirements for the construction, characteristics, performance including energy consumption of refrigerated storage cabinets and counters for professional use in commercial kitchens, hospitals, canteens, preparation areas of bars, bakeries, gelateria, institutional catering and similar professional areas.
The products covered in this European Standard are intended to store foodstuffs. It specifies test conditions and methods for checking that the requirements have been satisfied, as well as classification of the cabinets and counters, their marking and the list of their characteristics to be declared by the manufacturer.
It is not applicable to:
-   refrigerated cabinets used in the direct sale of foodstuffs;
-   cabinets that carry out food processing and not just storage function (e.g. bakery cabinets that chill, heat and humidity);
-   cabinets with water cooled condenser;
-   appliances with remote condensing unit;
-   appliances with open top tables and saladettes for preparation or storage of foodstuffs;
-   cabinet specifically intended for storage of specific foodstuffs (i.e. fresh meat, fresh fish, etc.) operating at a temperature different from those specified in Table 1;
-   chest freezers;
-   appliances intended for short time /intermittent normal operation during the full day;
-   built-in cabinet;
-   roll-in cabinet;
-   pass-through cabinet.