ECISS/TC 30 - Steel wires

TC - Correction of the coating mass unit in Table 3

This document specifies the composition, dimensions and mechanical properties of high carbon steel wire for reinforcing high pressure hoses. It is applicable to wire used as a multiple parallel wire braided or spirally wrapped reinforcement in a rubber or synthetic hose which is made to withstand relatively high bursting pressure.

This document specifies composition, dimensions and mechanical properties of round and flat wire used for strengthening the bead of all kinds of tyres.

This part of this European Standard specifies the requirements for mass, other properties and testing of tin coatings on steel wire and steel wire products of round or other cross section.

This part of this European Standard specifies the requirements for mass, other properties and testing of nickel coatings on steel wire and steel wire products of round or other cross-section.

This part of this European Standard specifies the requirements for mass, other properties and testing of copper, bronze and brass coatings on steel wire and steel wire products.

This part of this European Standard specifies the requirements for the mass, other properties and testing of aluminium coatings on steel wire and steel wire products of circular or other cross-section.

This European Standard specifies requirements for preferred form and dimensions, tolerance on dimensions and surface coating of loose steel wire nails for general applications.

This European Standard specifies requirements for the dimensions and coating of steel wire netting having meshes of hexagonal shape specified for engineering purposes.

To correct errors in Figure 2b and Table 2 footnote 6.

This Part of this European Standard specifies requirements for steel wire welded mesh panels for fencing. The panels are used for fencing parks, schools, sport stadia, public buildings, factories, airports, military sites, etc. This standard specifies the general characteristics of welded mesh supplied as panels and recommended coatings, properties and tolerances.

This part of this European Standard specifies requirements for steel wire weldedmesh fencing, of which there are many types for a variety of applications. It specifies the general characteristics of welded mesh fencing supplied as rolls or panels and coatings, properties and tolerances. The standard covers only orthogonal welded mesh i.e. wire welded at right angles to one another. For welded mesh fencing made from panels the specification covers only panels made from wires not greater than 10 mm.

This part of this European Standard specifies dimensions, properties and coatings of steel wire chain link fencing.

This part of this European Standard specifies preferred dimensions, properties and coatings of zinc and zinc alloy coated steel wire woven hinged joint and knotted mesh fencing.

This European Standard specifies zinc coated and zinc alloy coated steel barbed wire, conventional and reverse twist consisting of two stranded line wires, around which the barbs are tightly wound, a twist being imparted between the barbs to restrict their movement. The barbed wire entanglement has a single line wire, around which the barbs are wound.

This European Standard specifies requirements for the dimensions and coating of steel wire netting having meshes of hexagonal shape specified for agricultural, insulation and fencing purposes.

This part of this European Standard defines round and shaped non alloyed steel wire for use in the manufacture of ropes for mine hoisting, man-riding haulage, cableways for the transportation of passengers and other high duty applications.
This part of this European Standard refers to round wires and three types of shaped wire: full lock (Z), half lock (H) and trapezoidal (T).
In addition to the requirements of this part of this European Standard, the requirements of prEN 10264-1 also apply.
It does not apply to steel wire taken from manufactured ropes.
This part of this European Standard specifies the following for cold drawn non alloyed steel wire for ropes for high duty applications:
- dimensional tolerances;
- mechanical characteristics;
- requirements relating to the chemical composition of the steel wire;
- conditions to be satisfied by any coating.

This Part of this European Standard specifies the characteristics of stainless steel wire for the manufacture of ropes that are exposed to corrosion and in some cases to a moderate temperature.
This part of this European standard specifies the following for stainless steel wire for ropes
- dimensional tolerances;
- mechanical characteristics;
- requirements relating to the chemical composition of the stainless steel wire;
- conditions to be satisfied by any coating.

This part of this European Standard defines the general requirements for wire for ropes. Additional requirements are given in the following parts of this standard, which are specific to each category of wire. This standard specifies: - dimensional tolerances; - mechanical characteristics; - requirements relating to the chemical composition of the steel wire; - conditions to be satisfied by any coating.

This part of this European Standard defines cold drawn non alloyed steel wire used for the manufacture of: - ropes made of drawn wire for general applications as defined in EN ...; - ropes made of large diameter drawn wire as definied in EN ...; - ropes made of non alloyed drawn wire for which there is no specific EN standard. This part of this standard does not apply to steel wire taken from manufactured ropes.

This Part of this European Standard specifies the tolerances on diameter of round wire and, where applicable, on the length of round wire cut to length, for bright steel wire (i.e. uncoated), metallic coated steel wire and non-metallic coated steel wire. This standard should not be applied where other requirements for dimensions and tolerances are specified in a particular product standard.

This part of EN 10218 specifies the methods for the general testing of steel wire and wire products and which have been cold worked, annealed and/or coated and are of constant cross section, either round, or special section. It includes tensile testing, torsion testing, reverse bend testing, wrapping test, bend test, reverse torsion test, compression test, deep etch test, hardness test, quench hardenability test, fatigue test, wire cast measuremnet, artificial ageing, decarburization test, non-destructive tests, grain size tests, segregation test, non-metallic inclusion test and chemical analysis.

Complementary to EN 10245-1, this document specifies the characteristics and requirements for steel wire and wire products coated with polyester.
It covers both thermoplastic and thermosetting polyester.

1.1   This Part of EN 10270 applies to the grades of stainless steels listed in Table 1, which are usually used in the cold drawn condition in the form of wire of circular cross-section up to 10,00 mm in diameter, for the production of springs and spring parts that are exposed to corrosive effects and sometimes to slightly increased temperatures (see A.1).
1.2   In addition to the steels listed in Table 1 certain of the steel grades covered by EN 10088-3 e.g.1.4571, 1.4539, 1.4028 are also used for springs, although to much lesser extent. In these cases the mechanical properties (tensile strength, etc.) should be agreed between purchaser and supplier. Similarly, diameters between 10,00 mm and 15,00 mm may be ordered against this standard; in this case the parties should agree upon the required mechanical characteristics.
1.3   In addition to this part of EN 10270 the general technical delivery requirements of EN 10021 are applicable.

1.1   This Part of EN 10270 applies to oil hardened and tempered spring steel wire made from unalloyed or alloyed steels. They are primarily subject to torsional stresses such as in compression and extension springs and in special cases also for applications where the spring wire is subject to bending stresses such as lever springs.
As a rule unalloyed steels are used for applications at room temperature whereas alloyed steels are generally used at a temperature above room temperature. Alloyed steels may also be chosen for above average tensile strengths.
1.2   In addition to this part of EN 10270 the general technical delivery requirements of EN 10021 are applicable.

1.1   This Part of EN 10270 applies to patented cold drawn unalloyed steel wire of circular cross-section for the manufacture of mechanical springs for static duty and dynamic duty applications.
1.2   In addition to this part of EN  10270 the general technical delivery requirements of EN 10021 are applicable.

Complementary to prEN 10245-1, this Part 2 of prEN 10245 specifies the characteristics and requirements for steel wire and wire products coated with PVC.

This Standard specifies the requirements for the characteristics and testing methods for organic coating material suitable for the application on to steel wire and wire products of circular or other sections. Other organic materials which are applied intentionally or otherwise such as oils, greases, waxes and tempo rary finishes which do not become integral or a permanent part of the finished wire product are excluded from this standard.

Complementary to prEN 10245-1, this part of prEN 10245 specifies the characteristics and requirements for steel wire and wire products coated with polyethylene, (PE).

This Part of this European Standard specifies requirements for the properties of non-alloy zinc or zinc alloy coated steel wires used for the armouring of either submarine power and telecommunication cables in diameters ranging from 2,12 to 8,50 mm. The nominal wire diameters are specified in tables 2,3 and 4.

This Part of this European Standard specifies requirements for the properties of non-alloy carbon zinc or zinc alloy coated steel wire used primarily for the armouring of either land power or telecommunication cables i.e. cables intended to be buried  in the ground, in diameters ranging from 0,30 mm to 4,00 mm. The nominal wire diameters are specified in table 3.

This part of this European Standard specifies the requirements for mass, other properties and testing of zinc and zinc alloy coatings on steel wire and steel wire products of circular or other section.

This part of this European Standard specifies the requirements for the mass other properties and testing of non-ferrous metal coatings on steel wire and steel wire products of circular or other cross-section. This European Standard deals with requirements of general application and is of use for those coatings for which no particular requirement have been laid down in the following parts (2 to 6). Deviations are possible, particularly if required for well defined products. In such case, appropriate requirements shall be part of the relevant product standard.