SIST EN ISO 3822-1:1999/A1:2009

SLOVENSKI SIST EN ISO 3822-
1:1999/oprA1:2006

PREDSTANDARD
julij 2006
Akustika - Laboratorijski preskusi emisije hrupa armatur in naprav pri
inštalacijah za oskrbo z vodo - 1. del: Metode merjenja - Dopolnilo 1: Merilna
negotovost (ISO 3822-1:1999/DAM 1:2006)
Acoustics - Laboratory tests on noise emission from appliances and equipment
used in water supply installations - Part 1: Method of measurement - Amendment 1:
Measurement uncertainty (ISO 3822-1:1999/DAM 1:2006)
ICS 17.140.20; 91.140.60 Referenčna številka
SIST EN ISO 3822-
1:1999/oprA1:2006(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
EN ISO 3822-1:1999
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
May 2006
ICS 91.140.60; 17.140.20

English Version
Acoustics - Laboratory tests on noise emission from appliances
and equipment used in water supply installations - Part 1:
Method of measurement - Amendment 1: Measurement
uncertainty (ISO 3822-1:1999/DAM 1:2006)
Acoustique - Mesurage en laboratoire du bruit émis par les Akustik - Prüfung des Geräuschverhaltens von Armaturen
robinetteries et les équipements hydrauliques utilisés dans und Geräten der Wasserinstallation im Laboratorium - Teil
les installations de distribution d'eau - Partie 1: Méthode de 1: Messverfahren - Änderung 1: Messunsicherheit (ISO
mesurage - Amendement 1: Incertitude de mesure (ISO 3822-1:1999/DAM 1:2006)
3822-1:1999/DAM 1:2006)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 126.
This draft amendment A1, if approved, will modify the European Standard EN ISO 3822-1:1999. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status
as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3822-1:1999/prA1:2006: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
EN ISO 3822-1:1999/prA1:2006 (E)




Foreword

This document (EN ISO 3822-1:1999/prA1:2006) has been prepared by Technical Committee
ISO/TC 43 "Acoustics" in collaboration with Technical Committee CEN/TC 126 "Acoustic
properties of building elements and of buildings", the secretariat of which is held by AFNOR.

This document is currently submitted to the parallel Enquiry.



Endorsement notice

The text of ISO 3822-1:1999/DAM1:2006 has been approved by CEN as EN ISO 3822-
1:1999/prA1:2006 without any modifications.

2

---------------------- Page: 3 ----------------------
DRAFT AMENDMENT ISO 3822-1:1999/DAmd 1.2
ISO/TC 43/SC 2 Secretariat: DIN
Voting begins on: Voting terminates on:
2007-09-20 2008-02-20
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Acoustics — Laboratory tests on noise emission from
appliances and equipment used in water supply installations —
Part 1:
Method of measurement
AMENDMENT 1: Measurement uncertainty
Acoustique — Mesurage en laboratoire du bruit émis par les robinetteries et les équipements hydrauliques
utilisés dans les installations de distribution d'eau —
Partie 1: Méthode de mesurage
AMENDEMENT 1: Incertitude de mesure
ICS 17.140.20; 91.140.60

ISO/CEN PARALLEL ENQUIRY
The CEN Secretary-General has advised the ISO Secretary-General that this ISO/DIS covers a subject
of interest to European standardization. In accordance with the ISO-lead mode of collaboration as
defined in the Vienna Agreement, consultation on this ISO/DIS has the same effect for CEN
members as would a CEN enquiry on a draft European Standard. Should this draft be accepted, a
final draft, established on the basis of comments received, will be submitted to a parallel two-month FDIS
vote in ISO and formal vote in CEN.
In accordance with the provisions of Council Resolution 15/1993 this document is circulated in
the English language only.
Conformément aux dispositions de la Résolution du Conseil 15/1993, ce document est distribué
en version anglaise seulement.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©
International Organization for Standardization, 2007

---------------------- Page: 4 ----------------------
ISO 3822-1:1999/DAmd 1.2
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the
...