SIST EN IEC 60598-2-22:2022

SLOVENSKI STANDARD
SIST EN IEC 60598-2-22:2022
01-september-2022
Nadomešča:
SIST EN 60598-2-22:2015
SIST EN 60598-2-22:2015/A1:2020
SIST EN 60598-2-22:2015/AC:2015
SIST EN 60598-2-22:2015/AC:2016
Svetilke - 2-22. del: Posebne zahteve - Svetilke za zasilno razsvetljavo (IEC 60598-2
-22:2021)
Luminaires - Part 2-22: Particular requirements - Luminaires for emergency lighting (IEC
60598-2-22:2021)
Leuchten - Teil 2-22: Besondere Anforderungen - Leuchten für Notbeleuchtung (IEC
60598-2-22:2021)
Luminaires - Partie 2-22: Règles particulières - Luminaires pour éclairage de secours
(IEC 60598-2-22:2021)
Ta slovenski standard je istoveten z: EN IEC 60598-2-22:2022
ICS:
29.140.40 Svetila Luminaires
91.160.10 Notranja razsvetljava Interior lighting
SIST EN IEC 60598-2-22:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60598-2-22:2022

---------------------- Page: 2 ----------------------
SIST EN IEC 60598-2-22:2022


EUROPEAN STANDARD EN IEC 60598-2-22

NORME EUROPÉENNE

EUROPÄISCHE NORM June 2022
ICS 29.140.40 Supersedes EN 60598-2-22:2014 + AC:2015 + A1:2020 +
AC:2016-05 + AC:2016-09
English Version
Luminaires - Part 2-22: Particular requirements - Luminaires for
emergency lighting
(IEC 60598-2-22:2021)
Luminaires - Partie 2-22: Exigences particulières - Leuchten - Teil 2-22: Besondere Anforderungen - Leuchten
Luminaires pour éclairage de secours für Notbeleuchtung
(IEC 60598-2-22:2021) (IEC 60598-2-22:2021)
This European Standard was approved by CENELEC on 2022-02-16. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60598-2-22:2022 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60598-2-22:2022
EN IEC 60598-2-22:2022 (E)
European foreword
The text of document 34D/1635/FDIS, future edition 5 of IEC 60598-2-22, prepared by SC 34D
"Luminaires" of IEC/TC 34 "Lighting" was submitted to the IEC-CENELEC parallel vote and approved
by CENELEC as EN IEC 60598-2-22:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-12-24
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-06-24
document have to be withdrawn
This document supersedes EN 60598-2-22:2014 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document is read in conjunction with EN IEC 60598-1.
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association, and supports essential
requirements of EU Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZZ, which is an
integral part of this document.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60598-2-22:2021 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60364-5-56 NOTE Harmonized as HD 60364-5-56
2

---------------------- Page: 4 ----------------------
SIST EN IEC 60598-2-22:2022
EN IEC 60598-2-22:2022 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60073 - Basic and safety principles for man-machine EN 60073 2002
interface, marking and identification - Coding
principles for indicators and actuators
IEC 60598-1 - Luminaires - Part 1: General requirements EN IEC 60598-1 2021
and tests
IEC 60896-21 - Stationary lead-acid batteries - Part 21: Valve EN 60896-21 2004
regulated types - Methods of test
IEC 61056-1 - General purpose lead-acid batteries (valve- EN 61056-1 2012
regulated types) - Part 1: General
requirements, functional characteristics -
Methods of test
IEC 61347-2-2 - Lamp controlgear - Part 2-2: Particular EN 61347-2-2 2012
requirements for d.c. or a.c. supplied
electronic step-down convertors for filament
lamps
IEC 61347-2-3 - Lamp controlgear - Part 2-3: Particular EN 61347-2-3 2011
requirements for a.c. and/or d.c. supplied
electronic control gear for fluorescent lamps

 +AC 2011

A1 2017
IEC 61347-2-7 - Lamp controlgear - Part 2-7: Particular EN 61347-2-7 2012
requirements for battery supplied electronic

controlgear for emergency lighting (self-

contained)

+ A1 2019

+ A2 2022
3

---------------------- Page: 5 ----------------------
SIST EN IEC 60598-2-22:2022
EN IEC 60598-2-22:2022 (E)
Publication Year Title EN/HD Year
IEC 61347-2-12 - Lamp controlgear - Part 2-12: Particular EN 61347-2-12 2005
requirements for d.c. or a.c. supplied
electronic ballasts for discharge lamps
(excluding fluorescent lamps)

A1 2010
IEC 61347-2-13 - Lamp controlgear - Part 2-13: Particular EN 61347-2-13 2014
requirements for d.c. or a.c. supplied
electronic controlgear for LED modules

A1 2017
IEC 61951-1 - Secondary cells and batteries containing EN 61951-1 2017
alkaline or other non-acid electrolytes -
Portable sealed rechargeable single cells -
Part 1: Nickel-cadmium
IEC 61951-2 - Secondary cells and batteries containing EN 61951-2 2017
alkaline or other non-acid electrolytes -
Portable sealed rechargeable single cells -
Part 2: Nickel-metal hydride
IEC 62034 - Automatic test systems for battery powered EN 62034 2012
emergency escape lighting
IEC 62620 2014 Secondary cells and batteries containing EN 62620 2015
alkaline or other non-acid electrolytes -
Secondary lithium cells and batteries for use
in industrial applications
IEC 62133-2 2017 Secondary cells and batteries containing EN 62133-2 2017
alkaline or other non-acid electrolytes -
Safety requirements for portable sealed
secondary cells, and for batteries made from
them, for use in portable applications - Part 2:
Lithium systems

+prA1 2020 (in
preparation)
IEC 62391-1 2015 Fixed electric double-layer capacitors for use EN 62391-1 2016
in electric and electronic equipment - Part 1:
Generic specification

+AC 2016

+AC 2019
IEC 62391-2 2006 Fixed electric double-layer capacitors for use EN 62391-2 2006
in electronic equipment - Part 2: Sectional
specification - Electric double-layer
capacitors for power application
ISO 3864-1 2011 Graphical symbols - Safety colours and - -
safety signs - Part 1: Design principles for
safety signs and safety markings
ISO 3864-4 2011 Graphical symbols_- Safety colours and - -
safety signs - Part 4: Colorimetric and
photometric properties of safety sign
materials
ISO 30061 2007 Emergency lighting - -
4

---------------------- Page: 6 ----------------------
SIST EN IEC 60598-2-22:2022
EN IEC 60598-2-22:2022 (E)
Publication Year Title EN/HD Year
CIE 121 SPI - The Photometry and Goniophotometry of - -
Luminaires - Supplement 1: Luminaires for
Emergency Lighting

5

---------------------- Page: 7 ----------------------
SIST EN IEC 60598-2-22:2022
EN IEC 60598-2-22:2022 (E)
Annex ZB
(informative)

A-deviations
A-deviation: National deviation due to regulations, the alteration of which is for the time being outside
the competence of the CEN-CENELEC national member.
This European Standard falls under Directive 2006/95/EC.
NOTE (from CEN-CENELEC IR Part 2:2011, 2.17) Where standards fall under EU Directives, it is the view of the
Commission of the European Communities (OJ No C 59; 1982-03-09) that the effect of the decision of the Court
of Justice in case 815/79 Cremonini/Vrankovich (European Court Reports 1980, p. 3583) is that compliance with
A- deviations is no longer mandatory and that the free movement of products complying with such a standard
should not be restricted except under the safeguard procedure provided for in the relevant Directive or
Regulation.
A-deviations in an EFTA-country are valid instead of the relevant provisions of the European Standard
in that country until they have been removed.
Clause Deviation
22.6.18 France Ministry of the Interior, Overseas and Local Authorities - Order of 11 December
2009 approving various provisions supplementing and amending Regulation for fire
hazard safety for buildings open to the public - Clause EL 10 paragraph 1.
In premises open to the public, electrical installations shall have only permanent
fittings.
22.11.1 France Ministry of the Interior, Overseas and Local Authorities - Order of 11 December
2009 approving various provisions supplementing and amending Regulation for fire

hazard safety for buildings open to the public - Clause EL 10 paragraph 1.
In premises open to the public, electrical installations shall have only permanent
fittings.
22.6.15 France Ministry of the Interior - Order of 19 November 2001 approving various
provisions supplementing and amending regulation for fire hazard safety for buildings
open to the public - Clauses EC 9 and EC 10.
The required photometric characteristics of products are only based on the “rated
lumen output” as defined in 22.3.14, which shall be measured. Therefore the
photometric data distribution of the luminaire may not to be provided or checked.
22.17.1 France Ministry of the Interior - Order of 19 November 2001 approving various
provisions supplementing and amending regulation for fire hazard safety for buildings
open to the public - Clauses EC 9 and EC 10.
The required photometric characteristics of products are only based on the “rated
lumen output” as defined in 22.3.14, which shall be measured. Therefore the
photometric data distribution of the luminaire may not to be provided or checked.

6

---------------------- Page: 8 ----------------------
SIST EN IEC 60598-2-22:2022
EN IEC 60598-2-22:2022 (E)
Annex ZZ
(informative)

Relationship between this European standard and the safety objectives
of Directive 2014/35/EU [2014 OJ L96] aimed to be covered
This European Standard has been prepared under a Commission’s standardization request relating to
harmonized standards in the field of the Low Voltage Directive, M/511, to provide one voluntary means
of conforming to safety objectives of Directive 2014/35/EU of the European Parliament and of the
Council of 26 February 2014 on the harmonization of the laws of the Member States relating to the
making available on the market of electrical equipment designed for use within certain voltage limits
[2014 OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding safety objectives of
that Directive, and associated EFTA regulations.
Table ZZ.1 — Correspondence between this European standard and Annex I of Directive
2014/35/EU [2014 OJ L96]
Clause(s) / sub-clause(s)
Remarks /
Safety objectives of Directive 2014/35/EU
Notes
of this EN
1. General conditions
a) the essential characteristics, the recognition and 22.6
observance of which will ensure that electrical
22.17
equipment will be used safely and in applications for
which it was made, shall be marked on the electrical
equipment, or, if this is not possible, on an
accompanying document;
b) the electrical equipment, together with its All
component parts, shall be made in such a way as to
ensure that it can be safely and properly assembled
and connected;
c) the electrical equipment shall be so designed and See item 2 and 3 of this
manufactured as to ensure that protection against table
the hazards set out in points 2 and 3 is assured,
providing that the equipment is used in applications
for which it was made and is adequately maintained.
2. Protection against hazards arising from the
electrical equipment
Measures of a technical nature shall be laid down in
accordance with point 1, in order to ensure that:
a) persons and domestic animals are adequately 22.7
protected against the danger of physical injury or
22.8
other harm which might be caused by direct or
22.9
indirect contact;
22.10
22.11
22.12
22.15
22.20
7

---------------------- Page: 9 ----------------------
SIST EN IEC 60598-2-22:2022
EN IEC 60598-2-22:2022 (E)
Clause(s) / sub-clause(s)
Remarks /
Safety objectives of Directive 2014/35/EU
Notes
of this EN
b) temperatures, arcs or radiation which would cause 22.7
a danger, are not produced;
22.8
22.13
22.15
c) persons, domestic animals and property are 22.7
adequately protected against non-electrical dangers
22.15
caused by the electrical equipment which are
22.8
revealed by experience;
22.18
22.20
22.21
d) the insulation is suitable for foreseeable 22.8
conditions.
22.14
22.15
22.20
3. Protection against hazards which may be
caused by external influences on the electrical
equipment
Technical measures shall be laid down in
accordance with point 1, in order to ensure that the
electrical equipment:
a) meets the expected mechanical requirements in 22.6
such a way that persons, domestic animals and
22.7
property are not endangered;
b) is resistant to non-mechanical influences in 22.14
expected environmental conditions, in such a way
22.16
that persons, domestic animals and property are not
22.19
endangered;
c) does not endanger persons, domestic animals and 22.7
property in foreseeable conditions of overload.
22.13
22.16
22.19
22.20
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.

8

---------------------- Page: 10 ----------------------
SIST EN IEC 60598-2-22:2022



IEC 60598-2-22

®


Edition 5.0 2021-12




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Luminaires –

Part 2-22: Particular requirements – Luminaires for emergency lighting




Luminaires –

Partie 2-22: Exigences particulières – Luminaires pour éclairage de secours
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.140.40 ISBN 978-2-8322-1053-8




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 11 ----------------------
SIST EN IEC 60598-2-22:2022
– 2 – IEC 60598-2-22:2021 © IEC 2021
CONTENTS
FOREWORD . 3
22.1 Scope . 5
22.2 Normative references . 5
22.3 Terms and definitions . 6
22.4 General test requirements . 10
22.5 Classification of luminaires . 11
22.6 Marking . 11
22.7 Construction . 13
22.8 Creepage distances and clearances . 16
22.9 Provision of earthing . 16
22.10 Terminals . 16
22.11 External and internal wiring . 16
22.12 Protection against electric shock . 17
22.13 Endurance test and thermal test . 17
22.14 Resistance to dust and moisture . 19
22.15 Insulation resistance and electric strength . 19
22.16 Resistance to heat, fire and tracking . 19
22.17 Photometric data . 20
22.18 Changeover operation . 21
22.19 High temperature operation . 21
22.20 Battery chargers for self-contained emergency luminaires . 22
22.21 Test devices for emergency operation . 22
Annex A (normative) ESSSs for self-contained emergency luminaires . 23
Annex B (normative) Luminaire classification . 28
Annex C (normative) Luminance measurements . 30
Annex D (informative) Rest mode and remote inhibiting mode facilities . 31
Annex E (normative) Requirements for self-contained portable emergency luminaires . 33
Bibliography . 38

Figure C.1 – Typical example of measurement positions . 30

Table 1 – Voltage per cell to which the battery is discharged . 18
Table D.1 – Time scale rest mode and inhibiting mode versus status of normal mains
supply . 31

---------------------- Page: 12 ----------------------
SIST EN IEC 60598-2-22:2022
IEC 60598-2-22:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

LUMINAIRES –

Part 2-22: Particular requirements –
Luminaires for emergency lighting

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 60598-2-22 has been prepared by subcommittee 34D: Luminaires of IEC technical
committee 34: Lighting. It is an International Standard.
This fifth edition cancels and replaces the fourth edition published in 2014 and
Amendment 1:2017. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) update of requirements for rest mode and inhibiting mode;
b) clarification of high temperature operation tests;
c) introduction of new requirements for lithium batteries;
d) introduction of new requirements for electric double layer capacitors (EDLCs);

---------------------- Page: 13 ----------------------
SIST EN IEC 60598-2-22:2022
– 4 – IEC 60598-2-22:2021 © IEC 2021
e) clarification of resistance to heat, fire and tracking;
f) clarification of test facilities for self-contained luminaires;
g) clarification of the test method for contrast measurements of exit signs.
The text of this International Standard is based on the following documents:
Draft Report on voting
34D/1635/FDIS 34D/1642/RVD

Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement,
available at www.iec.ch/members_experts/refdocs. The main document types developed by
IEC are described in greater detail at www.iec.ch/standardsdev/publications.
This Part 2-22 is to be used in conjunction with the latest edition of IEC 60598-1 and its
amendment(s). It was established on the basis of the ninth edition (2020) of that standard.
NOTE 1 When "Part 1" is mentioned in this document, it refers to IEC 60598-1.
NOTE 2 In this document, the following print type is used:
– compliance statements: in italic type.
A list of all parts in the IEC 60598 series, published under the general title Luminaires, can be
found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 14 ----------------------
SIST EN IEC 60598-2-22:2022
IEC 60598-2-22:2021 © IEC 2021 – 5 –
LUMINAIRES –

Part 2-22: Particular requirements –
Luminaires for emergency lighting



22.1 Scope
This part of IEC 60598 specifies requirements for emergency luminaires for use with electrical
lamps on emergency power supplies not exceeding 1 000 V.
This document does not cover the effects of non-emergency voltage reductions on luminaires
incorporating high pressure discharge lamps.
This document gives general requirements for emergency lighting equipment.
In this document, the term "lamp" which also includes "light source(s)" where appropriate, is
used.
22.2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60073, Basic and safety principles for man-machine interface, marking and identification
– Coding principles for indicators and actuators
IEC 60155, Glow-starters for fluorescent lamps
IEC 60598-1, Luminaires – Part 1: General requirements and tests
IEC 60896-21, Stationary lead-acid batteries – Part 21: Valve regulated types – Methods of
test
IEC 61032:1997, Protection of persons and equipment by enclosures – Probes for verification
IEC 61056-1, General purpose lead-acid batteries (valve-regulated types) – Part 1: General
requirements, functional characteristics – Methods of test
IEC TR 61341, Method of measurement of centre beam intensity and beam angle(s) of
reflector lamps
IEC 61347-2-2, Lamp controlgear – Part 2-2: Particular requirements for d.c. or a.c. supplied
electronic step-down convertors for filament lamps
IEC 61347-2-3:2011, Lamp control gear – Part 2-3: Particular requirements for a.c. and/or d.c.
supplied electronic control gear for fluorescent lamps

---------------------- Page: 15 ----------------------
SIST EN IEC 60598-2-22:2022
– 6 – IEC 60598-2-22:2021 © IEC 2021
IEC 61347-2-7:2011, Lamp controlgear – Part 2-7: Particular requirements for battery
supplied electronic controlgear for emergency lighting (self-contained)
IEC 61347-2-7:2011/AMD1:2017
IEC 61347-2-7:2011/AMD2:2021
IEC 61347-2-12, Lamp controlgear – Part 2-12: Particular requirements for d.c. or a.c.
supplied electronic ballasts for discharge lamps (excluding fluorescent lamps)
IEC 61347-2-13, L
...