SIST-TS CLC/TS 50625-3-2:2016

SLOVENSKI STANDARD
SIST-TS CLC/TS 50625-3-2:2016
01-junij-2016
=DKWHYH]D]ELUDQMHORJLVWLNRLQREGHODYRRGSDGQHHOHNWULþQHLQHOHNWURQVNH
RSUHPH:(((GHO7HKQLþQDVSHFLILNDFLMD]DSUHSUHþHYDQMHRQHVQDåHQMD
6YHWLONH
Collection, logistics & Treatment requirements for WEEE - Part 3-2: Technical
specification for de-pollution - Lamps
Exigences de collecte, de logistique et de traitement pour les déchets d'équipements
électriques et électroniques (DEEE) - Partie 3-2 : Spécification technique pour la
dépollution - Lampes
Ta slovenski standard je istoveten z: CLC/TS 50625-3-2:2016
ICS:
13.020.40 Onesnaževanje, nadzor nad Pollution, pollution control
onesnaževanjem in and conservation
ohranjanje
13.030.99 Drugi standardi v zvezi z Other standards related to
odpadki wastes
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
SIST-TS CLC/TS 50625-3-2:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TS CLC/TS 50625-3-2:2016

---------------------- Page: 2 ----------------------

SIST-TS CLC/TS 50625-3-2:2016

TECHNICAL SPECIFICATION CLC/TS 50625-3-2

SPÉCIFICATION TECHNIQUE

TECHNISCHE SPEZIFIKATION
May 2016
ICS 13.030.99; 29.140.01
English Version
Collection, logistics & Treatment requirements for WEEE - Part
3-2: Technical specification for de-pollution - Lamps
Exigences de collecte, de logistique et de traitement pour Sammlung, Logistik und Behandlung von Elektro- und
les déchets d'équipements électriques et électroniques Elektronik-Altgeräten (WEEE) - Teil 3-2: Technische
(DEEE) - Partie 3-2: Spécification technique pour la Spezifikation zur Schadstoffentfrachtung - Lampen
dépollution - Lampes
This Technical Specification was approved by CENELEC on 2016-02-09.

CENELEC members are required to announce the existence of this TS in the same way as for an EN and to make the TS available promptly
at national level in an appropriate form. It is permissible to keep conflicting national standards in force.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. CLC/TS 50625-3-2:2016 E

---------------------- Page: 3 ----------------------

SIST-TS CLC/TS 50625-3-2:2016
CLC/TS 50625-3-2:2016
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 De-pollution monitoring . 7
4.1 Introduction . 7
4.2 Target value methodology . 7
4.3 Mass Balance methodology. 7
4.4 Analysis methodology . 7
5 Overview of the applicable methodologies — Applicable methodologies . 8
6 Large appliances . 8
7 Cooling and freezing appliances . 8
8 CRT Display /FPD appliances . 8
9 Lamps . 9
9.1 Introduction . 9
9.2 Analysis methodology . 9
10 Small appliances . 9
11 Protocol for components removed during a batch process . 9
Annex A (normative) Sampling protocol for the physically smallest non-metallic mechanical treatment
fraction . 10
Annex B (normative) Sampling protocol for plastics . 11
Annex C (normative) Targets . 12
Annex D (informative) Target calculation example — Calculation example for large appliance. 13
Annex E (informative) Void . 14
Annex AA (normative) Sampling protocol for the lamp treatment fractions . 15
AA.1 Introduction . 15
AA.2 Number and size of samples . 15
AA.3 Principles of sampling . 16
AA.3.1 Sampling during treatment process . 16
AA.3.2 Sampling after a treatment process . 16
AA.4 Mixed sample preparation . 16
AA.5 Mixed sample reduction . 17
AA.6 Packaging of samples . 17
Annex BB (normative) Analysis of mercury in the lamp treatment fractions . 18
BB.1 Introduction . 18
BB.2 Principles . 18
BB.3 Verification . 18
2

---------------------- Page: 4 ----------------------

SIST-TS CLC/TS 50625-3-2:2016
CLC/TS 50625-3-2:2016
Annex CC (informative) Remarks on the analysis of mercury in heterogeneous metal or mixed metal-plastic
fractions . 19
Bibliography . 20

3

---------------------- Page: 5 ----------------------

SIST-TS CLC/TS 50625-3-2:2016
CLC/TS 50625-3-2:2016
European foreword
This document (CLC/TS 50625-3-2:2016) has been prepared by CLC/TC 111X “Environment”.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under Mandate M/518 given to CENELEC by the European Commission
and the European Free Trade Association.
CLC/TS 50625-3, Collection, logistics and treatment requirements for WEEE, is composed with the following
parts:
— Part 3-1: Specification for de-pollution — General;
— Part 3-2: Technical specification for de-pollution — Lamps [the present document].
— Part 3-4: Specification for de-pollution — Temperature exchange equipment [currently in preparation].
This Technical Specification is to be used in conjunction with the latest edition of CLC/TS 50625-3-1.
This Technical Specification supplements or modifies the corresponding clauses in CLC/TS 50625-3-1, so as
to convert that publication into the TS: Treatment specification for lamps.
When a particular subclause of Part 3-1 is not mentioned in this Part 3-2, that subclause applies as far as is
reasonable. When this standard states “addition”, “modification” or “replacement”, the relevant text in Part 3-
1 is to be adapted accordingly.
NOTE The following numbering system is used:
— subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;
— unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including
those in a replaced clause or subclause;
— additional annexes are lettered AA, BB, etc.
4

---------------------- Page: 6 ----------------------

SIST-TS CLC/TS 50625-3-2:2016
CLC/TS 50625-3-2:2016
Introduction
In order to support EN 50625-2-1 and thereby fulfil the requirement of the European Commission’s Mandate
M/518 it is necessary to include normative requirements, such as target and limit values for the analysis, into
a document that is able to be revised to take into account both practical experience and changes in
treatment technologies.
5

---------------------- Page: 7 ----------------------

SIST-TS CLC/TS 50625-3-2:2016
CLC/TS 50625-3-2:2016
1 Scope
Clause 1 is replaced with the following:
This European Technical Specification is intended to be used in conjunction with the WEEE Treatment
Standard for lamps, EN 50625-2-1, and the Technical Specification CLC/TS 50625-3-1:2015 for de-pollution
– General.
2 Normative references
Clause 2 is replaced with the following:
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 488, District heating pipes — Preinsulated bonded pipe systems for directly buried hot water networks —
Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of
polyethylene
EN 13650, Soil improvers and growing media — Extraction of aqua regia soluble elements
EN 14899, Characterization of waste — Sampling of waste materials — Framework for the preparation and
application of a Sampling Plan
EN 15002, Characterization of waste — Preparation of test portions from the laboratory sample
CEN/TR 15310-1, Characterization of waste — Sampling of waste materials — Part 1: Guidance on
selection and application of criteria for sampling under various conditions
CEN/TR 15310-2, Characterization of waste — Sampling of waste materials — Part 2: Guidance on
sampling techniques
CEN/TR 15310-3, Characterization of waste — Sampling of waste materials — Part 3: Guidance on
procedures for sub-sampling in the field
CEN/TR 15310-4, Characterization of waste — Sampling of waste materials — Part 4: Guidance on
procedures for sample packaging, storage, preservation, transport and delivery
CEN/TR 15310-5, Characterization of waste — Sampling of waste materials — Part 5: Guidance on the
process of defining the sampling plan
EN 50574 (all parts), Collection, logistics & treatment requirements for end-of-life household appliances
containing volatile fluorocarbons or volatile hydrocarbons
EN 50625-1:2014, Collection, logistics & Treatment requirements for WEEE — Part 1: General treatment
requirements
EN 50625-2-1:2014, Collection, logistics and treatment requirements for WEEE — Part 2-1: Treatment
requirements for lamps
EN 62321-4, Determination of certain substances in electrotechnical products — Part 4: Mercury in
polymers, metals and electronics by CV-AAS, CV-AFS, ICP-OES and ICP-MS (IEC 62321-4)
EN ISO 12846, Water quality — Determination of mercury — Method using atomic absorption spectrometry
(AAS) with and without enrichment (ISO 12846)
6

---------------------- Page: 8 ----------------------

SIST-TS CLC/TS 50625-3-2:2016
CLC/TS 50625-3-2:2016
EN ISO 15587-1, Water quality — Digestion for the determination of selected elements in water — Part 1:
Aqua regia digestion (ISO 15587-1)
EN ISO 15587-2, Water quality — Digestion for the determination of selected elements in water — Part 2:
Nitric acid digestion (ISO 15587-2)
EN ISO 17294-2, Water quality — Application of inductively coupled plasma mass spectrometry (ICP-MS) —
Part 2: Determination of 62 elements (ISO 17294-2)
EN ISO 17852, Water quality — Determination of mercury — Method using atomic fluorescence
spectrometry (ISO 17852)
EN ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories
(ISO/IEC 17025)
ISO 16772, Soil quality — Determination of mercury in aqua regia soil extracts with cold-vapour atomic
spectrometry or cold-vapour atomic fluorescence spectrometry
EPA Method 6020 - 1: Revision 1, February 2007, Inductively coupled plasma mass spectrometry
EPA Method 7473 - 1: Revision 0, February 2007, Mercury in solids and solutions by thermal desorption,
amalgamation and atomic absorption spectrophotometry
3 Terms and definitions
This clause of EN 50625-1 and CLC/TS 50625-3-1 is applicable.
4 De-pollution monitoring
4.1 Introduction
This subclause of CLC/TS 50625-3-1 is applicable.
4.2 Target value methodology
This subclause of CLC/TS 50625-3-1 is not applicable.
4.3 Mass Balance methodology
This subclause of CLC/TS 50625-3-1 is not applicable.
4.4 Analysis methodology
Subclause 4.4.is r
...