oSIST prEN IEC 60335-2-39:2026/oprAA:2026

SLOVENSKI STANDARD
01-julij-2026
Gospodinjski in podobni električni aparati - Varnost - 2-39. del: Posebne zahteve
za komercialne električne večnamenske kuhalne posode - Dopolnilo AA
Household and similar electrical appliances - Safety - Part 2-39: Particular requirements
for commercial electric multi-purpose cooking pans
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-39:
Besondere Anforderungen für elektrische Mehrzweck-Koch- und -Bratpfannen für den
gewerblichen Gebrauch
Appareils électrodomestiques et analogues - Sécurité - Partie 2-39: Exigences
particulières pour les sauteuses électriques à usage commercial
Ta slovenski standard je istoveten z: prEN IEC 60335-2-39:2026/prAA:2026
ICS:
97.040.50 Majhni gospodinjski aparati Small kitchen appliances
oSIST prEN IEC 60335-2- en
39:2026/oprAA:2026
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD DRAFT
prEN IEC 60335-2-39:2026
NORME EUROPÉENNE
EUROPÄISCHE NORM
prAA
May 2026
ICS 97.040.50 -
English Version
Household and similar electrical appliances - Safety - Part 2-39:
Particular requirements for commercial electric multi-purpose
cooking pans
Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und
Partie 2-39: Exigences particulières pour les sauteuses ähnliche Zwecke - Teil 2-39: Besondere Anforderungen für
électriques à usage commercial elektrische Mehrzweck-Koch- und -Bratpfannen für den
gewerblichen Gebrauch
This draft amendment prAA, if approved, will modify the European Standard prEN IEC 60335-2-39:2026; it is submitted to CENELEC
members for enquiry.
Deadline for CENELEC: 2026-08-14.

It has been drawn up by CLC/TC 61.

If this draft becomes an amendment, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.

This draft amendment was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 81655 Ref. No. prEN IEC 60335-2-39:2026/prAA:2026 E

Contents Page
18 European foreword . 3
19 1 Modification to the Introduction . 4
20 2 Modification to Clause 1, “Scope” . 4
21 3 Modification to Clause 2, “Normative references” . 5
22 4 Modification to Clause 3, “Terms and definitions” . 5
23 5 Modification to Clause 7, “Marking and instructions” . 5
24 6 Modification to Clause 11, “Heating”. 6
25 7 Modification to Clause 15, “Moisture resistance” . 6
26 8 Modification to Clause 18, “Endurance” . 6
27 9 Modification to Clause 19, “Abnormal operation” . 7
28 10 Modification to Clause 22, “Construction” . 7
29 11 Modification to Clause 25, “Supply connection and external flexible cords” . 8
30 12 Modification to Clause 29, “Clearances, creepage distances and solid insulation" . 8
31 13 Modification to the annexes . 8
32 14 Modification to Bibliography . 20
33 European foreword
34 This document (prEN IEC 60335-2-39:2026/prAA:2026) has been prepared by CLC/TC 61 "Safety of household
35 and similar electrical appliances".
36 This document is currently submitted to the Enquiry.
37 The following dates are proposed:
• latest date by which the existence of this (doa) dav + 6 months
document has to be announced at national level
• latest date by which this document has to be (dop) dav + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dav + 36 months
conflicting with this document have to be (to be confirmed or
withdrawn modified when voting)
38 This document will modify prEN IEC 60335-2-39:2026 and all its amendments and corrigenda (if any).
39 prEN IEC 60335-2-39:2026/prAA:2026 includes the following significant technical modifications:
40 — introduce requirements for power driven moving parts;
41 — introduce mechanical test set-up clarifications;
42 — introduce the hygienic requirements;
43 — introduce ergonomic requirements.
44 This document is read in conjunction with EN IEC 60335-2-39:2026 and EN IEC 60335-2-39/A1:2026.
45 The numbering system for European clauses, subclauses, notes, tables, figures and annexes that are additional
46 to those in the IEC standard are prefixed with the letter “Z”.
47 This document has been prepared under a standardization request addressed to CENELEC by the European
48 Commission. The Standing Committee of the EFTA State subsequently approves these requests for its Member
49 States.
50 For the relationship with EU legislation, see informative Annexes ZZA, ZZB and ZZC, which are an integral part
51 of this document.
Secretary’s note: The text contained in the Secretary’s notes will be removed from the standard before
publication, as it is provided solely to inform stakeholders about the reasons for introducing the European
common modifications.
Secretary’s Note: The above sentence in lines 60/61 will be removed when the BT approves the removal of
the link to legislation.
53 1 Modification to the Introduction
54 Delete the words “manufacturer's”.
55 2 Modification to Clause 1, “Scope”
56 Replace the fourth paragraph starting with “As far as is practicable…” with the following:
57 “This document deals with the reasonably foreseeable hazards presented by appliances that are encountered
58 by all persons in and around the installation place or workplace.”
59 Convert the paragraph starting with “Attention is drawn to the…” into a note.
60 Addition:
61 With European Amendment A11, EN IEC 60335-2-39:2024+A11:2024 is superseded.
62 This European Amendment A11 supplements or modifies the corresponding clauses of the standards below:
63 — EN IEC 60335-1:2023 (Part 1)
64 — EN IEC 60335-2-39:2026 (Part 2)
65 The appliance can be combined with a fuel burning function, in which case EN IEC 60335-2-102 and
66 EN IEC 60335-2-39 cover the electrical safety and some other safety aspects. All safety aspects related to the
67 use of fuel-burning gas are covered by the relevant product standard for fuel-burning appliances.
Secretary’s note: the above sentence has been modified in base of the HAS comment.
69 For the purpose of this document, the term “appliance” includes the term “machine” where applicable.
70 Additional requirements for appliances with power driven moving parts are given in Annex ZE.
71 This document does not deal with any specific requirements on noise emitted from these appliances the
72 generated noise is not considered to be a relevant hazard. Thus, the emission sound pressure level LpA is
73 considered to be LpA ≤ 70 dB(A).
74 This document contains requirements for appliances with radio function, remote communication, and remote
75 operation.
76 For the scope of this document, the term “radio appliance” is used with the same meaning of “radio equipment”.
77 For the scope of this document, the term “appliance” is used with the same meaning of “equipment”.
Secretary’s note: the above sentence has been modified in base of the RED HAS comment.
79 Compliance with this Part 2 when used together with the Part 1 provides one means of conformity with the
80 safety objectives as listed in Table ZZA.1, Table ZZB.1 and Table ZZC.1.
Secretary’s Note: The above sentence in lines 79/80 will be removed when the BT approves the removal of
the link to legislation.
As impacted by EN IEC 60335-1:2023/A11:2023 and EN IEC 60335-1:2023/prAB:2026.
As impacted by prEN IEC 60335-2-39:2026/prA1:2026.
81 3 Modification to Clause 2, “Normative references”
82 Addition:
83 EN 1672-2:2020, Food processing machinery - Basic concepts - Part 2: Hygiene and cleanability requirements
84 EN IEC 60335-1:2023, Household and similar electrical appliances - Safety - Part 1: General requirements
85 4 Modification to Clause 3, “Terms and definitions”
86 3.1.9 Replace “manufacturer's” with “user’s” (twice).
87 3.1.101 Delete “by the manufacturer”.
88 3.8.101 Replace the definition with the following:
89 “fixed construction containing supply facilities for wall mounted appliances on one or both sides”.
90 5 Modification to Clause 7, “Marking and instructions”
91 7.12 Modification
92 Replace the fourth paragraph starting with “This appliance is not intended for use by persons (including children)
93 …” with the following:
94 “The instructions shall state the substance of the following:
95 — This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or
96 lack of experience and knowledge, unless they have been given supervision or instruction concerning use
97 of the appliance by a person responsible for their safety.”
98 Add the following:
99 “The front cover of the instructions shall include the substance of the following:
100 CAUTION: Read the instructions before using the appliance
101 This wording may be replaced by symbols ISO 7000-0434A (2004-01) and ISO 7000-0790 (2016-08).”
102 Add the following:
103 “The instructions shall also state the maximum weight of the empty appliance.”
104 In the addition replace the sentence starting with “If the manufacturer.” with the following:
105 “If the intended use of the appliance shall be limited to less than the above, this shall be clearly stated in the
106 instructions.”
107 Replace the fourth paragraph of the addition with the following:
108 “If any of symbols IEC 60417-5021 (2002-10), ISO 7000-0434A (2004-01) or ISO 7000-0790 (2016-08) are
109 used on the product or in the instructions, their meaning shall be explained.”
110 Add the following:
111 “The instructions shall also state:
112 — the intended use of the appliance as covered by the scope of this document;

As impacted by EN IEC 60335-1:2023/A11:2023 and EN IEC 60335-1:2023/prAB:2026.
113 — instructions regarding user maintenance and operation of the appliance and, if necessary, instructions for
114 the training of operators;
115 — instructions designed to enable adjustment and maintenance to be carried out safely, including the
116 protective measures that should be taken during these operations;
117 — the conditions under which the appliance is stable during use, dismantling when out of use, testing or
118 foreseeable breakdowns;
119 — the operating method to be followed in the event of accident or breakdown to prevent unsafe actions;
120 — information regarding the use of personal protection equipment in case of spreading hot food stuff;
121 — a warning concerning possible slippery floor adjacent to the appliance.”
122 Replace the Modification with the following:
123 “This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack
124 of experience and knowledge, unless they have been given supervision or instruction concerning use of the
125 appliance by a person responsible for their safety.”
126 7.12.1 Add the following:
127 “The instructions for table-top appliances shall state that a support is needed so that the working height of the
128 appliance is between 695 and 980 mm.
129 The instructions shall state that any repairs shall be carried out by competent persons.
130 7.12.Z101
131 The instructions shall include the possible reasonably foreseeable misuse and, whenever relevant, a warning
132 against the effects it may have on the safe use of the appliance. At least, it shall include the substance of the
133 following:
134 WARNING: Appliances must be disconnected from their power supply during cleaning or maintenance and
135 when replacing parts.
136 Compliance is checked by inspection.”
137 6 Modification to Clause 11, “Heating”
138 11.2 Modification:
139 Delete “manufacturer’s”.
140 11.3 Modification:
141 Delete the sentence “Any measuring instrument giving the same results as the probe may be used.”.
142 11.7 Modification:
143 Replace “by the manufacturer” with “in the instruction”.
144 7 Modification to Clause 15, “Moisture resistance”
145 15.101 Modification:
146 Replace in the third paragraph starting with “The tap is fully opened…” “by the manufacturer” with “in the
147 instruction”.
148 8 Modification to Clause 18, “Endurance”
149 Replace the sentence “This clause of Part 1 is applicable.“ with “This clause of Part 1 is not applicable.“.
150 9 Modification to Clause 19, “Abnormal operation”
151 19.1 Modification:
152 Delete in the last paragraph starting with “A control or switching device …” the term “manufacturer’s”.
153 10 Modification to Clause 22, “Construction”
154 22.13 Addition:
155 Lids shall be equipped with at least one handle, if not motorized.
156 22.48 Addition:
157 After the first paragraph, add the following:
158 “For appliances within the scope of this document without cleaning system, Fluid Category is 2 according to
159 EN 61770:2009 .
160 For appliances within the scope of this document with cleaning system, Fluid Category is 3 according to
161 EN 61770:2009 ."
162 22.106 Add the following as a second paragraph:
163 “This requirement is met, if:
164 — the hinge incorporates a click stop; or
165 — the lid is counter balanced; or
166 — the lid can be opened through an angle of at least 100°.”
167 Replace the compliance criteria with the following:
168 “Compliance is checked by applying a force of 20 N in the most unfavourable position and direction to the raised
169 lid. The lid shall not fall back to its operating position.”
170 Add the following note:
171 “NOTE Z101  Lids that can be opened through an angle of at least 100°, even if placed against a wall, are not subjected to
172 this test.”
173 Add the following new subclauses:
174 “
175 22.Z.101 Appliances shall meet the following ergonomic requirements:
176 — the working height of the hob shall be between 695 and 980 mm,
177 — the rear edge of the pan shall be a maximum of 850 mm from the front edge of the appliance,
178 — operator controls shall be
179 — attached at a minimum height of 350 mm,
180 — clearly visible and identifiable,

As impacted by EN 61770:2009/AC:2011, EN 61770:2009/A11:2018, EN 61770:2009/A1:2019,
EN 61770:2009/A12:2022, EN 61770:2009/AC:2023 and EN 61770:2009/A13:2026.
181 — positioned within easy reach of the operator's hand,
182 — secured against accidental actuation, if their actuation could result in a hazard.
183 Compliance is checked by inspection.
184 NOTE Guidance can be found in EN 614-1 and EN 614-2.
185 22.Z.102 Appliances shall meet hygiene requirements.
186 Compliance is checked by inspection and by the requirements in Annex ZAA.
187 22.Z.103 Filling and draining taps shall be designed and constructed so that it is not possible to inadvertently
188 open them.
189 Compliance is checked by inspection and by manual test.
190 NOTE For example, this requirement is met when the valve handle is such that, when released, it returns automatically
191 to the closed position or is of the wheel type or is placed in a recess.”
192 11 Modification to Clause 25, “Supply connection and external flexible cords”
193 25.3 Modification:
194 Delete at the end of the first paragraph “manufacturer’s”.
195 12 Modification to Clause 29, “Clearances, creepage distances and solid insulation"
196 29.2 Modification:
197 Replace “unlikely to be” with “not”.
198 13 Modification to the annexes
199 The annexes of Part 1 and Part 2 are applicable except as follows:
200 Annex ZA
201 (normative)
203 Normative references to international publications with their
204 corresponding European publications
Publication Year Title EN/HD Year
Addition:
IEC 60584-1 - Thermocouples – Part 1: EMF specifications and EN 60584-1 2013
tolerances
ISO 898-1 - Mechanical properties of fasteners made of carbon EN ISO 898-1 2013
steel and alloy steel – Part 1: Bolts, screws and studs
with specified property classes – Coarse thread and
fine pitch thread
+ AC 2013
ISO 3506-1 - Mechanical properties of corrosion-resistant EN ISO 3506-1 2020
stainless steel fasteners – Part 1: Bolts, screws and
studs
ISO 3506-2 - Mechanical properties of corrosion-resistant EN ISO 3506-2 2020
stainless steel fasteners – Part 2: Nuts
ISO 3506-3 - Mechanical properties of corrosion-resistant EN ISO 3506-3 2025
stainless steel fasteners – Part 3: Set screws and
similar fasteners not under tensile stress
ISO 3506-4 - Mechanical properties of corrosion-resistant EN ISO 3506-4 2025
stainless steel fasteners – Part 4: Tapping screws
Household and similar electrical appliances - Safety EN IEC 60335-1 2023
- Part 1: General requirements
+ A11 2023
+ prAB 2026
Food processing machinery - Basic concepts - Part EN 1672-2 2020
2: Hygiene and cleanability requirements
205 Annex ZE
206 (normative)
208 Specific additio
...