Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions

This document specifies the tolerances on dimensions of aluminium and aluminium alloy drawn wire for general engineering applications (except aeronautical applications), covering diameters, thicknesses or widths or width across flats up to and including 20 mm.
It applies to drawn wires, except for electrical or welding purposes.
It does not apply to drawing stock.

Aluminium und Aluminiumlegierungen - Gezogene Drähte - Teil 3: Grenzabmaße

Dieses Dokument legt die Grenzabmaße für gezogene Drähte aus Aluminium und Aluminiumlegierungen für
allgemeine Anwendungen fest (ausgenommen Anwendungen in der Luftfahrt) und gilt für Durchmesser,
Dicken, Breiten oder Schlüsselweiten bis 20 mm.
Es gilt für gezogene Drähte, ausgenommen Drähte für elektrotechnische oder schweißtechnische Anwendungen.
Es gilt nicht für Vordraht.

Aluminium et alliages d'aluminium - Fil étiré - Partie 3: Tolérances sur dimensions

Le présent document spécifie les tolérances sur dimensions du fil étiré en aluminium ou en alliage
d'aluminium destiné à des applications mécaniques (à l'exception des rivets utilisés en aéronautique), et
correspondant à des diamètres, des épaisseurs ou des largeurs entre plats inférieures ou égales à 20 mm.
Il s'applique aux fils étirés, à l’exception des applications en électricité ou en soudage.
Il ne s’applique pas aux fils machine.

Aluminij in aluminijeve zlitine - Vlečena žica - 3. del: Tolerance mer

General Information

Status
Published
Publication Date
05-Oct-2008
ICS
77.150.10 - Aluminium products
Technical Committee
INEK - Nonferrous metals
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
24-Sep-2008
Due Date
29-Nov-2008
Completion Date
06-Oct-2008
Ref Project
EN 1301-3:2008 - Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions

Relations

Replaces
SIST EN 1301-3:1998 - Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions
Effective Date
01-Nov-2008

Overview

EN 1301-3:2008 (CEN) defines the tolerances on dimensions for aluminium and aluminium-alloy drawn wire used in general engineering applications (excluding aeronautical uses). It covers drawn wire forms - round, square, hexagonal and rectangular - with nominal dimensions up to and including 20 mm. The standard does not apply to wire for electrical or welding purposes, nor to drawing stock. Measurement and sampling conditions refer to EN 1301-1.

Key topics

  • Scope and applicability
    • Applies to aluminium and aluminium-alloy drawn wire for general engineering (not aeronautical, electrical or welding wire, nor drawing stock).
    • Limits dimensions up to 20 mm.
  • Dimensional tolerances by cross-section
    • Round wire: tolerances vary by diameter range (example values: ≈ ±0.02 mm for ≤1 mm up to ≈ ±0.11 mm for 18–20 mm). Ovality (difference between max and min diameter on one cross-section) shall not exceed 50% of the total tolerance.
    • Square & hexagonal wire: tolerances on width across flats (examples: ±0.04 mm for ≤3 mm; ±0.14 mm for 15–20 mm). Deviations from a regular polygon are included.
    • Rectangular wire: separate tolerances for thickness and width (examples: thickness ±0.03 mm for ≤1 mm; width ±0.04 mm for ≤1 mm; up to ±0.14 mm thickness and ±0.18 mm width for 15–20 mm).
  • Measurement rules
    • Sampling and measurement procedures are to follow EN 1301-1.
  • Exclusions
    • Cross-section distortions caused by winding/unwinding are explicitly not covered.

Applications

EN 1301-3:2008 is used by:

  • Manufacturers and wire-drawing mills to specify and control dimensional quality of aluminium drawn wire.
  • Quality control and inspection teams for acceptance testing, sampling and measurement.
  • Procurement and specification writers who require clear dimensional tolerance limits in purchase orders and product datasheets.
  • Designers and component makers who select drawn aluminium wire for fasteners, formed parts and general engineering components (non-aeronautical).
  • Standards bodies and conformity assessors referencing harmonized European tolerances.

Related standards

  • EN 1301-1: Technical conditions for inspection and delivery (normative reference for sampling and measurement).
  • EN 1301-2: Mechanical properties (other part of the EN 1301 series).

Keywords: EN 1301-3:2008, aluminium drawn wire tolerances, tolerances on dimensions, aluminium and aluminium alloys, drawn wire, CEN.

Frequently Asked Questions

SIST EN 1301-3:2008 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions". This standard covers: This document specifies the tolerances on dimensions of aluminium and aluminium alloy drawn wire for general engineering applications (except aeronautical applications), covering diameters, thicknesses or widths or width across flats up to and including 20 mm. It applies to drawn wires, except for electrical or welding purposes. It does not apply to drawing stock.

This document specifies the tolerances on dimensions of aluminium and aluminium alloy drawn wire for general engineering applications (except aeronautical applications), covering diameters, thicknesses or widths or width across flats up to and including 20 mm. It applies to drawn wires, except for electrical or welding purposes. It does not apply to drawing stock.

SIST EN 1301-3:2008 is classified under the following ICS (International Classification for Standards) categories: 77.150.10 - Aluminium products. The ICS classification helps identify the subject area and facilitates finding related standards.

SIST EN 1301-3:2008 has the following relationships with other standards: It is inter standard links to SIST EN 1301-3:1998. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

SIST EN 1301-3:2008 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium und Aluminiumlegierungen - Gezogene Drähte - Teil 3: GrenzabmaßeAluminium et alliages d'aluminium - Fil étiré - Partie 3: Tolérances sur dimensionsAluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions77.150.10Aluminijski izdelkiAluminium productsICS:Ta slovenski standard je istoveten z:EN 1301-3:2008SIST EN 1301-3:2008en,fr,de01-november-2008SIST EN 1301-3:2008SLOVENSKI
STANDARDSIST EN 1301-3:19981DGRPHãþD

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1301-3September 2008ICS 77.150.10Supersedes EN 1301-3:1997
English VersionAluminium and aluminium alloys - Drawn wire - Part 3:Tolerances on dimensionsAluminium et alliages d'aluminium - Fil étiré - Partie 3:Tolérances sur dimensionsAluminium und Aluminiumlegierungen - Gezogene Drähte -Teil 3: GrenzabmaßeThis European Standard was approved by CEN on 16 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1301-3:2008: ESIST EN 1301-3:2008
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...