SIST EN 683-2:2024
(Main)Aluminium and aluminium alloys - Finstock - Part 2: Mechanical properties
Aluminium and aluminium alloys - Finstock - Part 2: Mechanical properties
This document specifies the mechanical properties of wrought aluminium and wrought aluminium alloy finstock.
The chemical composition limits of these materials are specified in EN 573-3, unless otherwise agreed between supplier and purchaser.
The designations of wrought aluminium and wrought aluminium alloys and the temper designations used in this document are specified in EN 573-3, and the temper designations are defined in EN 515.
Aluminium und Aluminiumlegierungen - Vormaterial für Wärmeaustauscher (Finstock) - Teil 2: Mechanische Eigenschaften
Dieses Dokument legt die mechanischen Eigenschaften von Vormaterial für Wärmeaustauscher aus Aluminium und Aluminium-Knetlegierungen fest.
Die Grenzen der chemischen Zusammensetzung dieser Werkstoffe sind in EN 573-3 festgelegt, falls nichts anderes zwischen Lieferer und Käufer vereinbart wurde.
Die in diesem Dokument verwandten Bezeichnungen für Aluminium und Aluminium-Knetlegierungen sind in EN 573-3 festgelegt und die Bezeichnungen der Werkstoffzustände in EN 515 definiert.
Aluminium et alliages d'aluminium - Bandes pour échangeurs thermiques - Partie 2 : Caractéristiques mécaniques
Le présent document spécifie les caractéristiques mécaniques des bandes pour échangeurs thermiques en aluminium et alliages d'aluminium corroyés.
Les limites de la composition chimique de ces matériaux sont données dans l‘EN 573-3, sauf accord contraire entre le fournisseur et l’acheteur.
La désignation de l'aluminium et des alliages d'aluminium, ainsi que la désignation des états métallurgiques utilisées dans le présent document sont spécifiées dans l'EN 573-3 et la désignation des états métallurgiques est définie dans l'EN 515.
Aluminij in aluminijeve zlitine - Hladno valjani polizdelki za toplotne izmenjevalnike - 2. del: Mehanske lastnosti
Ta dokument določa mehanske lastnosti hladno valjanih polizdelkov za toplotne izmenjevalnike iz kovanega aluminija in kovanih aluminijevih zlitin.
Omejitve kemijske sestave za te materiale so določene v standardu EN 573-3, razen če se dobavitelj in kupec dogovorita drugače.
Oznake kovanega aluminija in kovanih aluminijevih zlitin ter oznake za popuščanje, uporabljene v tem dokumentu, so določene v standardu EN 573-3. Oznake za popuščanje so opredeljene v standardu EN 515.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 683-2:2024
01-junij-2024
Aluminij in aluminijeve zlitine - Hladno valjani polizdelki za toplotne izmenjevalnike
- 2. del: Mehanske lastnosti
Aluminium and aluminium alloys - Finstock - Part 2: Mechanical properties
Aluminium und Aluminiumlegierungen - Vormaterial für Wärmeaustauscher (Finstock) -
Teil 2: Mechanische Eigenschaften
Aluminium et alliages d'aluminium - Bandes pour échangeurs thermiques - Partie 2 :
Caractéristiques mécaniques
Ta slovenski standard je istoveten z: EN 683-2:2024
ICS:
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 683-2:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 683-2:2024
---------------------- Page: 2 ----------------------
SIST EN 683-2:2024
EN 683-2
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2024
EUROPÄISCHE NORM
ICS 77.120.10 Supersedes EN 683-2:2006
English Version
Aluminium and aluminium alloys - Finstock - Part 2:
Mechanical properties
Aluminium et alliages d'aluminium - Bandes pour Aluminium und Aluminiumlegierungen - Vormaterial
échangeurs thermiques - Partie 2 : Caractéristiques für Wärmeaustauscher (Finstock) - Teil 2: Mechanische
mécaniques Eigenschaften
This European Standard was approved by CEN on 27 February 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 683-2:2024 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 683-2:2024
EN 683-2:2024 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Tensile testing . 4
5 Mechanical properties . 6
6 Rounding of test results . 6
Annex A (informative) Rules for rounding . 11
Bibliography . 12
2
---------------------- Page: 4 ----------------------
SIST EN 683-2:2024
EN 683-2:2024 (E)
European foreword
This document (EN 683-2:2024) has been prepared by Technical Committee CEN/TC 132 “Aluminium
and aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2024, and conflicting national standards shall
be withdrawn at the latest by October 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for ident
...
SLOVENSKI STANDARD
oSIST prEN 683-2:2023
01-junij-2023
Aluminij in aluminijeve zlitine - Hladno valjani polizdelki za toplotne izmenjevalnike
- 2. del: Mehanske lastnosti
Aluminium and aluminium alloys - Finstock - Part 2: Mechanical properties
Aluminium und Aluminiumlegierungen - Vormaterial für Wärmeaustauscher (Finstock) -
Teil 2: Mechanische Eigenschaften
Aluminium et alliages d'aluminium - Bandes pour échangeurs thermiques - Partie 2 :
Caractéristiques mécaniques
Ta slovenski standard je istoveten z: prEN 683-2
ICS:
77.150.10 Aluminijski izdelki Aluminium products
oSIST prEN 683-2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 683-2:2023
---------------------- Page: 2 ----------------------
oSIST prEN 683-2:2023
DRAFT
EUROPEAN STANDARD
prEN 683-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2023
ICS Will supersede EN 683-2:2006
English Version
Aluminium and aluminium alloys - Finstock - Part 2:
Mechanical properties
Aluminium et alliages d'aluminium - Bandes pour Aluminium und Aluminiumlegierungen - Vormaterial
échangeurs thermiques - Partie 2 : Caractéristiques für Wärmeaustauscher (Finstock) - Teil 2: Mechanische
mécaniques Eigenschaften
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 132.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 683-2:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 683-2:2023
prEN 683-2:2023 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Tensile testing . 4
5 Mechanical properties . 6
6 Rounding of test results . 6
Annex A (normative) Rules for rounding .11
Bibliography .12
2
---------------------- Page: 4 ----------------------
oSIST prEN 683-2:2023
prEN 683-2:2023 (E)
European foreword
This document (prEN 683-2:2023) has been prepared by Technical Committee CEN/TC 132 “Aluminium
and aluminium alloys”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.