SIST EN ISO 1514:2024

SLOVENSKI STANDARD
01-september-2024
Nadomešča:
SIST EN ISO 1514:2016
Barve in laki - Standardne ploščice za preskušanje (ISO 1514:2024)
Paints and varnishes - Standard panels for testing (ISO 1514:2024)
Beschichtungsstoffe - Norm-Probenplatten (ISO 1514:2024)
Peintures et vernis - Panneaux normalisés pour essai (ISO 1514:2024)
Ta slovenski standard je istoveten z: EN ISO 1514:2024
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 1514
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2024
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 1514:2016
English Version
Paints and varnishes - Standard panels for testing (ISO
1514:2024)
Peintures et vernis - Panneaux normalisés pour essai Beschichtungsstoffe - Norm-Probenplatten (ISO
(ISO 1514:2024) 1514:2024)
This European Standard was approved by CEN on 3 July 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1514:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 1514:2024) has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2025, and conflicting national standards shall
be withdrawn at the latest by January 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1514:2016.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 1514:2024 has been approved by CEN as EN ISO 1514:2024 without any modification.

International
Standard
ISO 1514
Sixth edition
Paints and varnishes — Standard
2024-07
panels for testing
Peintures et vernis — Panneaux normalisés pour essai
Reference number
ISO 1514:2024(en) © ISO 2024
ISO 1514:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 1514:2024(en)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Steel panels . 2
4.1 Properties .2
4.2 Storage prior to preparation .2
4.3 Preparation by solvent cleaning .2
4.4 Preparation by aqueous cleaning (spray or immersion process) .3
4.5 Preparation by abrasion .3
4.5.1 General .3
4.5.2 Hand abrasion .3
4.5.3 Circular mechanical abrasion .4
4.5.4 Linear grinding .4
4.6 Inspection and cleaning .4
4.7 Preparation by phosphate treatment .4
4.7.1 General .4
4.7.2 Amorphous iron phosphate treatment .4
4.8 Preparation by blast-cleaning .4
5 Tinplate panels . 4
5.1 Properties .4
5.2 Preparation by solvent or aqueous cleaning .5
5.3 Preparation by abrasion .5
6 Zinc- and zinc-alloy-coated panels . 5
6.1 Properties .5
6.2 Preparation by solvent cleaning .5
6.3 Preparation by aqueous cleaning .5
7 Aluminium panels . 6
7.1 Properties .6
7.2 Preparation by solvent cleaning .6
7.3 Preparation by aqueous cleaning .6
7.4 Preparation by abrasion .6
8 Coil-coating panels of steel or aluminium . 6
8.1 Properties .6
8.2 Coating .6
8.3 Substrate .7
8.4 Preparation by solvent cleaning .7
9 Plastics panels . 7
9.1 Properties .7
9.2 Preparation by solvent cleaning .7
9.3 Preparation by detergent cleaning .7
9.4 Pre-treatment by flaming .7
10 Glass-fibre reinforced plastic composite panels (GRP) . 7
10.1 Properties .7
10.2 Preparation by solvent cleaning .7
10.3 Preparation by detergent cleaning .7
11 Carbon-fibre reinforced plastic composite panels (CFRP) . 8
11.1 Properties .8
11.2 Preparation by solvent cleaning .8

iii
ISO 1514:2024(en)
11.3 Preparation by detergent cleaning .8
12 Glass panels . 8
12.1 Properties .8
12.2 Preparation by solvent cleaning .8
12.3 Preparation by detergent cleaning .8
13 Hardboard. 8
13.1 Properties .8
13.2 Preparation .8
14 Gypsum plasterboards panels and gypsum boards with fibrous reinforcement panels . 9
14.1 Properties .9
14.2 Preparation .9
15 Fibre-reinforced cement panels . 9
16 Concrete . 9
Annex A (informative) General guidelines on preparation of steel panels by blast-cleaning .10
Annex B (informative) Common substrate panels .11
Bibliography .12

iv
ISO 1514:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139, Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This sixth edition cancels and replaces the fifth edition (ISO 1514:2016), which has been technically revised.
The main changes are as follows:
— Clause 3 (terms and definitions) has been added;
— the preparation of plastics substrate including glass-fibre reinforced plastic composite panels (GRP) and
carbon-fibre reinforced plastic composite panels (CFRP) has been updated;
— concrete test panels have been added;
— the normative references have been updated.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

v
ISO 1514:2024(en)
Introduction
For many of the most widely used test methods for paints and varnishes, the type of panel used and the
particular way in which it is prepared for use can affect the test results to a significant degree. Consequently,
it is important to standardize as carefully as possible both the panels and the procedures used to prepare
the panels prior to painting.
It is not possible to include in this document all the types of panels and preparation needed for paint
testing. Thus, this document describes preparation procedures that are known to be reproducible and gives
additional guidance and requirements in instances where there can still be doubt, due to lack of international
uniformity of the procedure.
Common substrate panels and the documents which specify their technical delivery conditions are listed in
Table B.1.
vi
International Standard ISO 1514:2024(en)
Paints and varnishes — Standard panels for testing
1 Scope
This document specifies several types of standard panels and provides guidance and requirements on the
procedures for their preparation prior to painting. The standard panels described in this document are
intended for use in general methods of test for paints, varnishes and related products.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 1268-1, Fibre-reinforced plastics — Methods of producing test plates — Part 1: General conditions
ISO 1268-2, Fibre-reinforced plastics — Methods of producing test plates — Part 2: Contact and spray-up
moulding
ISO 1268-3, Fibre-reinforced plastics — Methods of producing test plates — Part 3: Wet compression moulding
ISO 1268-4, Fibre-reinforced plastics — Methods of producing test plates — Part 4: Moulding of prepregs
ISO 1268-5, Fibre-reinforced plastics — Methods of producing test plates — Part 5: Filament winding
ISO 1268-6, Fibre-reinforced plastics — Methods of producing test plates — Part 6: Pultrusion moulding
ISO 1268-7, Fibre-reinforced plastics — Methods of producing test plates — Part 7: Resin transfer moulding
ISO 1268-8, Fibre-reinforced plastics — Methods of producing test plates — Part 8: Compression moulding of
SMC and BMC
ISO 1268-9, Fibre-reinforced plastics — Methods of producing test plates — Part 9: Moulding of GMT/STC
ISO 1268-10, Fibre-reinforced plastics — Methods of producing test plates — Part 10: Injection moulding of BMC
and other long-fibre moulding compounds — General principles and moulding of multipurpose test specimens
ISO 1268-11, Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC
and other long-fibre moulding compounds — Small plates
ISO 2409, Paints and varnishes — Cross-cut test
ISO 2808, Paints and varnishes — Determination of film thickness
ISO 4618, Paints and varnishes — Vocabulary
ISO 8336, Fibre-cement flat sheets — Product specification and test methods
ISO 11949, Cold-reduced tinmill products — Electrolytic tinplate
ISO 21920-2, Geometrical product specifications (GPS) — Surface texture: Profile — Part 2: Terms, definitions
and surface texture parameters
EN 520, Gypsum plasterboards — Definitions, requirements and test methods
EN 622-1, Fibreboards — Specifications — Part 1: General requirements

ISO 1514:2024(en)
EN 622-2, Fibreboards — Specifications — Part 2: Requirements for hardboards
EN 622-3, Fibreboards — Specifications — Part 3: Requirements for medium boards
EN 622-4, Fibreboards — Specifications — Part 4: Requirements for softboards
EN 622-5, Fibreboards — Specifications — Part 5: Requirements for dry process boards (MDF)
EN 1396, Aluminium and aluminium alloys — Coil coated sheet and strip for general applications — Specifications
EN 1766, Products and systems for the protection and repair of concrete structures — Test methods — Reference
concretes for testing
EN 10205, Cold redu
...