SIST EN 12453:2017+A1:2022
(Main)Industrial, commercial and garage doors and gates - Safety in use of power operated doors - Requirements and test methods
Industrial, commercial and garage doors and gates - Safety in use of power operated doors - Requirements and test methods
This European Standard specifies requirements and test methods for the safety in use of power operated door, gate and barrier, intended for installation in areas in the reach of persons, and for which the main intended use is giving safe access for goods and vehicles accompanied or driven by persons in industrial, commercial or residential premises.
This European Standard also covers power operated vertically moving commercial doors such as rolling shutters and rolling grilles, used in retail premises which are mainly provided for goods protection.
This European Standard deals with all significant hazards, hazardous situations and events relevant to the power operation of industrial, commercial and garage doors, and gates when they are used as intended and under conditions of misuse which are reasonably foreseeable as identified in Clause 4.
All lifetime phases of the machinery including transportation, assembly, dismantling, disabling and scrapping are considered by this standard.
This European Standard does not apply to
- lock gates and dock gates;
- doors on lifts;
- doors on vehicles;
- armoured doors;
- doors mainly for the retention of animals, unless they are at the site perimeter ;
- theatre textile curtains;
- horizontally moving power operated doors mainly intended for pedestrian use;
- doors outside the reach of people (such as crane gantry fences);
- railway barriers;
- barriers intended solely for use by pedestrians;
- barriers used solely for vehicles on motorways.
Whenever the term "door" is used in this document, it shall be deemed to cover the full scope of types and variances of doors, gates and barriers in the scope of this Standard.
This European Standard does not deal with any specific requirements on noise emitted from power operated door, gate and barrier, intended for installation in areas in the reach of persons, and for which the main intended use is giving safe access for goods and vehicles accompanied or driven by persons in industrial, commercial or residential premises as their noise emission is not considered to be a relevant hazard.
NOTE Noise emission of power operated doors is not a significant hazard for the users of these products. It is a comfort aspect.
This European Standard is not applicable to machinery which are manufactured before the date of publication of the standard.
Tore - Nutzungssicherheit kraftbetätigter Tore - Anforderungen und Prüfverfahren
Den ersten Absatz durch Folgendes ersetzen:
"Dieses Dokument legt Anforderungen und Prüfverfahren hinsichtlich der Nutzungssicherheit kraftbetätigter industrieller und gewerblicher Tore sowie Garagentore und Schranken fest, die für den Einbau in Zugangsbereichen mit Personenverkehr vorgesehen sind und deren bestimmungsgemäße Verwendung hauptsächlich darin besteht, den sicheren Zugang von Waren und Fahrzeugen, die von Personen geführt oder gesteuert werden, zu industriellen und gewerblichen Anlagen sowie zu Wohnanlagen zu ermöglichen."
Portes et portails industriels, commerciaux et résidentiels - Sécurité d’utilisation des portes et portails motorisés - Exigences et méthodes d'essai
Le présent document définit les exigences et les méthodes d’essai relatives à la sécurité d’utilisation des portes, portails et barrières motorisés équipant des locaux industriels, commerciaux et résidentiels, qui sont destinés à être installés dans des zones accessibles aux personnes, et dont l’utilisation principale prévue est de permettre l’accès en toute sécurité des marchandises et des véhicules accompagnées ou conduits par des personnes à des locaux industriels, commerciaux ou résidentiels.
La présente Norme européenne concerne également les portes commerciales à déplacement vertical, tels que les grilles et rideaux à enroulement utilisées dans les locaux de vente au détail et dont l’utilisation principale prévue est la protection des marchandises.
La présente Norme européenne traite de tous les phénomènes dangereux, situations dangereuses et événements dangereux significatifs liés au fonctionnement motorisé des portes, portails et barrières lorsqu'ils sont utilisés comme prévu et dans des conditions de mauvaise utilisation raisonnablement prévisibles telles qu’identifiés à l’Article 4.
Le cycle de vie de la machine incluant le transport, l’assemblage, le démantèlement, la désactivation et la mise au rebut sont prises en compte dans cette norme.
La présente Norme européenne ne s’applique pas aux :
- Portes d’écluses et portes de bassin ;
- Portes d’ascenseurs ;
- Portes de véhicules ;
- Portes blindées ;
- Portes principalement destinées au parcage des animaux, à moins qu’elles ne soient dans le périmètre du site ;
- Rideaux de théâtre en tissu ;
- Blocs-portes motorisés à déplacement horizontal destinés à un usage piétonnier ;
- Portes situées hors d’atteinte des personnes (telles que barrières équipant les grues à portiques) ;
- Barrières de passages à niveau ;
- Barrières prévues à l’usage seul des piétons ;
- Barrières destinées uniquement aux véhicules sur autoroutes.
Chaque fois que le terme « porte » est utilisé dans le présent document, il doit être pris dans un sens large couvrant tous les types et variantes de portes, portails et barrières définis dans le domaine d’application de la présente norme.
La présente Norme européenne ne traite d'aucune exigence spécifique concernant le bruit émis par la porte, le portail et la barrière motorisée, destinée à être installée dans des zones accessibles aux personnes et dont l’utilisation principale prévue est de permettre l’accès en toute sécurité des marchandises et des véhicules accompagnés ou conduits par des personnes dans des locaux industriels, commerciaux ou résidentiels, car leur émission sonore n'est pas considérée comme un danger pertinent.
NOTE L'émission de bruit des portes motorisées ne représente pas un danger important pour les utilisateurs de ces produits. Il s’agit d’un aspect de confort.
La présente Norme européenne ne s’applique pas non plus aux machines fabriquées avant sa date de publication.
Vrata v industrijske in javne prostore ter garažna vrata - Varnost pri uporabi pogonskega mehanizma - Zahteve in preskusne metode (vključuje dopolnilo A1)
Ta evropski standard določa zahteve in preskusne metode za varnost pri uporabi vrat oziroma zapornic s pogonskim mehanizmom, ki so namenjene za namestitev v območjih, kjer so na dosegu posameznikom, in katerih glavni predvideni namen uporabe je omogočanje varnega dostopa za blago in vozila v spremstvu ali upravljanju oseb v industrijskih, poslovnih ter stanovanjskih objektih.
Ta evropski standard zajema tudi vrata v javne prostore na električni pogon, ki se pomikajo navpično, kot so roloji in rešetke, ki se uporabljajo v maloprodajnih prostorih ter so namenjene predvsem za zaščito blaga.
Ta evropski standard opisuje vse večje nevarnosti, nevarne situacije in dogodke v zvezi z delovanjem vrat v industrijske in javne prostore ter garažnih vrat in zapornic, kadar se ti uporabljajo v skladu s svojim namenom in pod pogoji razumno predvidene nepravilne uporabe, kot je opredeljeno v točki 4.
Ta standard obravnava vse življenjske faze izdelkov, vključno s transportom, montažo, razstavljanjem, onemogočanjem in razrezom.
Ta evropski standard se ne uporablja za:
– vodne zapornice in zapornice v dokih;
– vrata v dvigalih;
– vrata na vozilih;
– oklepna vrata;
– vrata, namenjena predvsem za zadrževanje živali, razen če so v območju lokacije;
– gledališke zavese iz tekstila;
– vodoravno premikajoča se vrata s pogonskim mehanizmom, namenjena predvsem za pešce;
– vrata na območjih izven dosega ljudi (npr. ograje portalnih žerjavov);
– železniške zapornice;
– zapornice, ki se uporabljajo izključno za pešce;
– zapornice, ki se uporabljajo izključno za vozila na avtocestah.
Izraz »vrata« na katerem koli mestu v tem dokumentu zajema vse vrste in različice vrat, pregrad in zapornic s področja uporabe tega standarda.
Ta evropski standard ne obravnava posebnih zahtev glede hrupa, ki ga povzročajo vrata, pregrade in zapornice s pogonskim mehanizmom, ki so namenjene za namestitev v območjih, kjer so na dosegu posameznikom, in katerih glavni predvideni namen uporabe je omogočanje varnega dostopa za blago in vozila v spremstvu ali upravljanju oseb v industrijskih, poslovnih ter stanovanjskih objektih, saj se njihove emisije hrupa ne obravnavajo kot pomembna nevarnost.
OPOMBA: Emisije hrupa vrat s pogonskim mehanizmom ne predstavljajo večje nevarnosti za uporabnike teh izdelkov. Gre bolj za vidik udobja.
Ta evropski standard se ne uporablja za izdelke, izdelane pred datumom objave tega standarda.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12453:2017+A1:2022
01-februar-2022
Nadomešča:
SIST EN 12453:2017
Vrata v industrijske in javne prostore ter garažna vrata - Varnost pri uporabi
pogonskega mehanizma - Zahteve in preskusne metode (vključuje dopolnilo A1)
Industrial, commercial and garage doors and gates - Safety in use of power operated
doors - Requirements and test methods
Tore - Nutzungssicherheit kraftbetätigter Tore - Anforderungen und Prüfverfahren
Portes et portails industriels, commerciaux et résidentiels - Sécurité d’utilisation des
portes et portails motorisés - Exigences et méthodes d'essai
Ta slovenski standard je istoveten z: EN 12453:2017+A1:2021
ICS:
91.060.50 Vrata in okna Doors and windows
91.090 Konstrukcije zunaj stavb External structures
SIST EN 12453:2017+A1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12453:2017+A1:2022
---------------------- Page: 2 ----------------------
SIST EN 12453:2017+A1:2022
EN 12453:2017+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2021
EUROPÄISCHE NORM
ICS 91.060.50 Supersedes EN 12453:2017
English Version
Industrial, commercial and garage doors and gates - Safety
in use of power operated doors - Requirements and test
methods
Portes et portails équipant les locaux industriels et Tore - Nutzungssicherheit kraftbetätigter Tore -
commerciaux et les garages - Sécurité à l'utilisation des Anforderungen und Prüfverfahren
portes motorisées - Exigences et méthodes d'essai
This European Standard was approved by CEN on 12 June 2017 and includes Amendment 1 approved by CEN on 16 December
2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12453:2017+A1:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12453:2017+A1:2022
EN 12453:2017+A1:2021 (E)
Contents Page
European foreword . 5
Introduction . 7
1 Scope . 8
2 Normative references . 9
3 Terms and definitions . 10
4 List of significant hazards . 12
4.1 General . 12
4.2 Hazards caused by crushing, shearing and drawing-in . 13
4.2.1 General . 13
4.2.2 !Hazards caused when persons can travel with the door" . 13
4.2.3 Hazards caused by impact . 13
4.3 Hazards caused by source of energy and power controls . 13
4.4 Manual operation . 14
4.5 Other hazards . 14
4.5.1 General . 14
4.5.2 Hazards caused by pass doors . 14
4.5.3 Hazards caused by imprisonment . 14
4.5.4 Hazards caused by trapping . 14
4.5.5 Hazards caused by falling or ejected parts or uncontrolled movement . 14
4.5.6 Hazards caused by the locking devices . 14
4.5.7 Hazards caused due to a loss of stability . 14
4.5.8 Hazards caused by glazing material . 15
4.5.9 Hazards caused by modification of settings . 15
5 Safety requirements and/or protective measures . 15
5.1 General . 15
5.1.1 General requirements . 15
5.1.2 Safety Function performed by control system. 15
5.1.3 Minimum level of safeguarding at the main closing edge . 16
5.2 Crushing, shearing and drawing-in . 17
5.2.1 General . 17
5.2.2 Safeguarding against hazards caused when persons can travel with the door . 21
5.2.3 Safeguarding against impact hazard . 21
5.3 Source of energy and power controls . 22
5.3.1 General . 22
5.3.2 Electrical drive units . 22
5.3.3 Hydraulic drive units . 25
5.3.4 Pneumatic drive units . 25
5.3.5 Restart after unintended interruption . 26
5.3.6 Supply disconnection . 26
5.4 Manual operation . 26
5.4.1 General . 26
5.4.2 Manual operation by direct movement of the door leaf . 26
5.4.3 Manual operation directly applied to the drive unit . 26
5.4.4 Balancing failure at manual operation . 26
5.4.5 Human physical strength for manual operation of the door leaf . 27
2
---------------------- Page: 4 ----------------------
SIST EN 12453:2017+A1:2022
EN 12453:2017+A1:2021 (E)
5.5 Other hazards . 27
5.5.1 Pass doors . 27
5.5.2 Imprisonment . 27
5.5.3 Trapping. 27
5.5.4 Falling or ejected parts or uncontrolled movement . 27
5.5.5 Locking devices . 28
5.5.6 Loss of stability . 28
5.5.7 Glazing material . 29
5.5.8 Modification of setting . 29
6 Verification of the safety requirements and/or protective measures . 29
6.1 General . 29
6.2 Crushing, shearing and drawing-in points . 29
6.2.1 General . 29
6.2.2 !Hazards caused when persons can travel with the door" . 31
6.2.3 Impact hazard . 31
6.3 Source of energy . 31
6.3.1 Electrical drive units . 31
6.3.2 Hydraulic drive units . 32
6.3.3 Pneumatic drive units . 32
6.3.4 Restart after unintended interruption . 32
6.3.5 Supply disconnection . 32
6.4 Manual operation . 32
6.4.1 Manual operation by direct movement of the door leaf . 32
6.4.2 Manual operation directly applied to the drive unit . 32
6.4.3 Balancing failure at manual operation . 32
6.4.4 Human physical strength for manual operation of the door leaf . 33
6.5 Other hazards . 33
6.5.1 Pass doors . 33
6.5.2 Imprisonment . 33
6.5.3 Trapping. 33
6.5.4 Falling or ejected parts or uncontrolled movement . 33
6.5.5 Locking devices . 34
6.5.6 Loss of stability . 34
6.5.7 Glazing material . 34
6.5.8 Modification of settings . 34
7 Information for use . 34
7.1 General . 34
7.2 Marking . 37
Annex A (normative) Limitation of forces . 38
A.1 Specifications . 38
A.2 Admissible forces . 38
Annex B (informative) Examples of mechanical protection and safety distances . 40
B.1 Examples of mechanical protection . 40
B.2 Examples of appropriate safety clearances and safety distances . 41
Annex C (normative) Force measuring method. 43
C.1 General . 43
C.2 Measuring equipment . 43
3
---------------------- Page: 5 ----------------------
SIST EN 12453:2017+A1:2022
EN 12453:2017+A1:2021 (E)
C.3 Points of measuring . 43
Annex D (normative) Testing method for presence detection . 53
D.1 General . 53
D.2 Test pieces . 53
D.3 Testing of supplementary device to be used with force limitation . 54
D.4 Testing of presence detection system to be used without force limitation . 57
Annex E (informative) Safeguarding against dropping by other design features incorporated
in the suspension system of vertically moving power operated door leaves . 61
Annex F (informative) Relationship between Hazards, Requirements and Test clauses . 62
Annex G (informative) Logbook . 64
Annex ZA (informative) Relationship between this European standard and the Essential
Requirements of Directive 2006/42/EC aimed to be covered . 65
Bibliography . 68
4
---------------------- Page: 6 ----------------------
SIST EN 12453:2017+A1:2022
EN 12453:2017+A1:2021 (E)
European foreword
This document (EN 12453:2017+A1:2021) has been prepared by Technical Committee CEN/TC 33
“Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2022, and conflicting national standards shall be
withdrawn at the latest by June 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document will supersedes !EN 12453:2017".
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral
part of this document.
This document includes Amendment 1 approved by CEN on 4 January 2021.
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
Compared with EN 12453:2000 and EN 12445:2000, the following changes have been made:
a) EN 12453 has been revised to be harmonized under Machinery Directive 2006/42/EC;
b) EN 12453 has been merged with EN 12445; as EN 12445:2000 will be withdrawn;
c) aligning structure of EN 12453 according to MD templates;
d) revision of the list of significant hazards (Clause 4);
e) revision of safety and/or protective measures (Clause 5);
f) revision of the verification of the safety requirements (Clause 6);
g) editorial revision of Annex A (limitation of forces);
h) introducing Annex B (Examples of mechanical protection and safety distances);
i) introducing Annex C (Force measuring method);
j) introducing Annex D (Testing method for presence detection);
k) introducing Annex E (Safeguarding against dropping by other design features incorporated in the
suspension system of vertically moving power operated door leaves);
l) introducing Annex ZA for harmonization of EN 12453 under MD.
5
---------------------- Page: 7 ----------------------
SIST EN 12453:2017+A1:2022
EN 12453:2017+A1:2021 (E)
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
6
---------------------- Page: 8 ----------------------
SIST EN 12453:2017+A1:2022
EN 12453:2017+A1:2021 (E)
Introduction
This document is a type C document as stated in EN ISO 12100.
This document is of relevance, in particular, for the following stakeholder groups representing the
market players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance etc.)
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events
are covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or type-
B standards, the requirements of this type-C standard take precedence over the requirements of the
other standards for machines that have been designed and built according to the requirements of this
type-C standard.
This document has been prepared to meet the needs of manufacturers, users and safety enforcement
authorities, with the primary purpose of providing design and performance for safety in use of power
operated industrial, commercial and garage doors and gates used by vehicular traffic.
Mechanical aspects of the doors are covered by normative references to
!EN 12604:2017+A1:2020".
7
---------------------- Page: 9 ----------------------
SIST EN 12453:2017+A1:2022
EN 12453:2017+A1:2021 (E)
1 Scope
!This document specifies requirements and test methods for the safety in use of power operated
industrial, commercial and garage doors, gates and barriers intended for installation in areas in the
reach of persons, and for which the main intended use is giving safe access for goods and vehicles
accompanied or driven by persons in industrial, commercial or residential premises."
This European Standard also covers power operated vertically moving commercial doors such as rolling
shutters and rolling grilles, used in retail premises which are mainly provided for goods protection.
This European Standard deals with all significant hazards, hazardous situations and events relevant to
the power operation of industrial, commercial and garage doors, and gates when they are used as
intended and under conditions of misuse which are reasonably foreseeable as identified in Clause 4.
All lifetime phases of the machinery including transportation, assembly, dismantling, disabling and
scrapping are considered by this standard.
This European Standard does not apply to:
— lock gates and dock gates;
— doors on lifts;
— doors on vehicles;
— armoured doors;
— doors mainly for the retention of animals, unless they are at the site perimeter;
— theatre textile curtains;
— horizontally moving power operated doors mainly intended for pedestrian use;
— doors outside the reach of people (such as crane gantry fences);
— railway barriers;
— barriers intended solely for use by pedestrians;
— barriers used solely for vehicles on motorways.
Whenever the term “door” is used in this document, it shall be deemed to cover the full scope of types
and variances of doors, gates and barriers in the scope of this Standard.
This European Standard does not deal with any specific requirements on noise emitted from power
operated door, gate and barrier, intended for installation in areas in the reach of persons, and for which
the main intended use is giving safe access for goods and vehicles accompanied or driven by persons in
industrial, commercial or residential premises as their noise emission is not considered to be a relevant
hazard.
NOTE Noise emission of power-operated doors is not a significant hazard for the users of these products. It is
a comfort aspect.
This European Standard is not applicable to machinery which are manufactured before the date of
publication of the standard.
8
---------------------- Page: 10 ----------------------
SIST EN 12453:2017+A1:2022
EN 12453:2017+A1:2021 (E)
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 349:1993+A1:2008, Safety of machinery — Minimum gaps to avoid crushing of parts of the human
body
EN 12433-1:1999, Industrial, commercial and garage doors and gates - Terminology - Part 1: Types of
doors
EN 12433-2:1999, Industrial, commercial and garage doors and gates - Terminology - Part 2: Parts of
doors
!EN 12604:2017+A1:2020, Industrial, commercial and garage doors and gates — Mechanical
aspects — Requirements and test methods"
!deleted text"
EN 12978:2003+A1:2009, Industrial, commercial and garage doors and gates - Safety devices for power
operated doors and gates - Requirements and test methods
EN 60335-1:2012, Household and similar electrical appliances — Safety — Part 1: General requirements
(IEC 60335-1:2012)
EN 60335-2-95:2015, Safety of household and similar electrical appliances — Part 2-95: Particular
requirements for drives for vertically moving garage doors for residential use (IEC 60335-2-95:2015)
EN 60335-2-103:2015, Household and similar electrical appliances — Safety — Part 2-103: Particular
requirements for drives for gates, doors and windows (IEC 60335-2-103:2015)
1
!EN 60529:1991," Degrees of protection provided by enclosures (IP Code)
2
EN 60204-1:2006, Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN 61000-6-1:2007, Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for
residential, commercial and light-industrial environments
EN 61000-6-2:2005, Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for
industrial environments
EN 61000-6-3:2007, Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission
standard for residential, commercial and light-industrial environments
EN 61000-6-4:2007, Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission
standard for industrial environments
1
As impacted by EN 60529:1991/A1:2000, EN 60529:1991/A2:2013, EN 60529:1991/corrigendum May 1993,
EN 60529:1991/A2:2013/AC:2019-02 and EN 60529:1991/AC:2016-12.
2
As impacted by EN 60204-1:2006/A1:2009 and EN 60204-1:2006/AC:2010.
9
---------------------- Page: 11 ----------------------
SIST EN 12453:2017+A1:2022
EN 12453:2017+A1:2021 (E)
EN 61032:1998, Protection of persons and equipment by enclosures - Probes for verification
EN ISO 4413:2010, Hydraulic fluid power - General rules and safety requirements for systems and their
components (IS
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.