SIST EN ISO 1460:2020
(Main)Metallic coatings - Hot dip galvanized coatings on ferrous materials - Gravimetric determination of the mass per unit area (ISO 1460:2020)
Metallic coatings - Hot dip galvanized coatings on ferrous materials - Gravimetric determination of the mass per unit area (ISO 1460:2020)
This document specifies a method of determining the mass per unit area of hot dip galvanized coatings
on ferrous materials.
Since an exact knowledge of the area of the surface is essential, this document is mainly applicable to
shapes whose areas are easy to determine. If, with heavy samples, the specifications of Clause 7 cannot
be met, then the hot dip galvanized coating mass is determined by another method.
Metallische Überzüge - Feuerverzinken auf Eisenwerkstoffen - Gravimetrisches Verfahren zur Bestimmung der flächenbezogenen Masse (ISO 1460:2020)
Dieses Dokument legt ein Verfahren für die Bestimmung der flächenbezogenen Masse von Feuerverzinkungen auf Eisenwerkstoffen fest.
Da die genaue Kenntnis der Größe der Oberfläche wesentlich ist, ist dieses Dokument hauptsächlich für Gegenstände mit solchen Formen anwendbar, deren Flächen leicht zu bestimmen sind. Falls bei Proben mit schwer zu bestimmender Oberfläche die Anforderungen in Abschnitt 7 nicht erfüllt werden können, ist die Masse der Schicht des Feuerverzinkungsüberzuges durch ein anderes Verfahren zu bestimmen.
Revêtements métalliques - Revêtements de galvanisation à chaud sur métaux ferreux - Détermination gravimétrique de la masse par unité de surface (ISO 1460:2020)
Le présent document spécifie une méthode pour la détermination de la masse par unité de surface des revêtements de galvanisation à chaud sur métaux ferreux.
La connaissance exacte de l'aire de la surface revêtue de zinc étant indispensable, le présent document est essentiellement applicable aux formes dont les surfaces sont faciles à déterminer. Si, avec des échantillons épais, les spécifications de l'Article 7 ne peuvent être satisfaites, la masse du revêtement de galvanisation à chaud est déterminée au moyen d'une autre méthode.
Kovinske prevleke - Prevleke na železnem materialu, nanesene z vročim pocinkanjem - Gravimetrijski postopki za ugotavljanje mase nanosa na enoto površine (ISO 1460:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 1460:2020
01-november-2020
Nadomešča:
SIST EN ISO 1460:1999
Kovinske prevleke - Prevleke na železnem materialu, nanesene z vročim
pocinkanjem - Gravimetrijski postopki za ugotavljanje mase nanosa na enoto
površine (ISO 1460:2020)
Metallic coatings - Hot dip galvanized coatings on ferrous materials - Gravimetric
determination of the mass per unit area (ISO 1460:2020)
Metallische Überzüge - Feuerverzinken auf Eisenwerkstoffen - Gravimetrisches
Verfahren zur Bestimmung der flächenbezogenen Masse (ISO 1460:2020)
Revêtements métalliques - Revêtements de galvanisation à chaud sur métaux ferreux -
Détermination gravimétrique de la masse par unité de surface (ISO 1460:2020)
Ta slovenski standard je istoveten z: EN ISO 1460:2020
ICS:
25.220.40 Kovinske prevleke Metallic coatings
SIST EN ISO 1460:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 1460:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 1460:2020
EN ISO 1460
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2020
EUROPÄISCHE NORM
ICS 25.220.40 Supersedes EN ISO 1460:1994
English Version
Metallic coatings - Hot dip galvanized coatings on ferrous
materials - Gravimetric determination of the mass per unit
area (ISO 1460:2020)
Revêtements métalliques - Revêtements de Metallische Überzüge - Feuerverzinken auf
galvanisation à chaud sur métaux ferreux - Eisenwerkstoffen - Gravimetrisches Verfahren zur
Détermination gravimétrique de la masse par unité de Bestimmung der flächenbezogenen Masse (ISO
surface (ISO 1460:2020) 1460:2020)
This European Standard was approved by CEN on 2 September 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1460:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 1460:2020
EN ISO 1460:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 1460:2020
EN ISO 1460:2020 (E)
European foreword
This document (EN ISO 1460:2020) has been prepared by Technical Committee ISO/TC 107 "Metallic
and other inorganic coatings" in collaboration with Technical Committee CEN/TC 262 “Metallic and
other inorganic coatings, including for corrosion protection and corrosion testing of metals and alloys”
the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall
be withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1460:1994.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 1460:2020 has been approved by CEN as EN ISO 1460:2020 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 1460:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 1460:2020
INTERNATIONAL ISO
STANDARD 1460
Third edition
2020-09
Metallic coatings — Hot dip galvanized
coatings on ferrous materials —
Gravimetric determination of the
mass per unit area
Revêtements métalliques — Revêtements de galvanisation à chaud
sur métaux ferreux — Détermination gravimétrique de la masse par
unité de surface
Reference number
ISO 1460:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 1460:2020
ISO 1460:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 1460:2020
ISO 1460:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Stripping solution . 1
6 Sampling . 1
7 Procedure. 1
8 Expression of results .
...
SLOVENSKI STANDARD
oSIST prEN ISO 1460:2020
01-maj-2020
Kovinske prevleke - Prevleke na železnem materialu, nanesene z vročim
pocinkanjem - Gravimetrijski postopki za ugotavljanje mase nanosa na enoto
površine (ISO/DIS 1460:2020)
Metallic coatings - Hot dip galvanized coatings on ferrous materials - Gravimetric
determination of the mass per unit area (ISO/DIS 1460:2020)
Metallische Überzüge - Feuerverzinken auf Eisenwerkstoffen - Gravimetrisches
Verfahren zur Bestimmung der flächenbezogenen Masse (ISO/DIS 1460:2020)
Revêtements métalliques - Revêtements de galvanisation à chaud sur métaux ferreux -
Détermination gravimétrique de la masse par unité de surface (ISO/DIS 1460:2020)
Ta slovenski standard je istoveten z: prEN ISO 1460
ICS:
25.220.40 Kovinske prevleke Metallic coatings
oSIST prEN ISO 1460:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 1460:2020
---------------------- Page: 2 ----------------------
oSIST prEN ISO 1460:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 1460
ISO/TC 107/SC 4 Secretariat: BSI
Voting begins on: Voting terminates on:
2020-03-19 2020-06-11
Metallic coatings — Hot dip galvanized coatings on ferrous
materials — Gravimetric determination of the mass per
unit area
Revêtements métalliques — Revêtements de galvanisation à chaud sur métaux ferreux — Détermination
gravimétrique de la masse par unité de surface
ICS: 25.220.40
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 1460:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020
---------------------- Page: 3 ----------------------
oSIST prEN ISO 1460:2020
ISO/DIS 1460:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 1460:2020
ISO/DIS 1460:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Stripping solution . 1
6 Sampling . 1
7 Procedure. 1
8 Expression of results . 2
8.1 Method of calculation . 2
8.2 Reproducibility . 2
9 Test report . 2
© ISO 2020 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 1460:2020
ISO/DIS 1460:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.