SIST EN 1175-2:1998/kFprA1:2010

SLOVENSKI STANDARD
SIST EN 1175-2:1998/kFprA1:2010
01-julij-2010
9DUQRVWYR]LO]DWDOQLWUDQVSRUW(OHNWULþQH]DKWHYHGHO6SORãQH]DKWHYH]D
YR]LOD]DWDOQLWUDQVSRUW]PRWRUMHP]QRWUDQMLP]JRUHYDQMHP'RSROQLOR$
Safety of industrial trucks - Electrical requirements - Part 2: General requirements of
internal combustion engine powered trucks
Sicherheit von Flurförderzeugen - Elektrische Anforderungen - Teil 2: Allgemeine
Anforderungen für Flurförderzeuge mit Verbrennungsmotoren
Sécurité des chariots de manutention - Prescriptions électriques - Partie 2: Prescriptions
générales des chariots équipés d'un moteur thermique
Ta slovenski standard je istoveten z: EN 1175-2:1998/FprA1
ICS:
43.060.01 Motorji z notranjim Internal combustion engines
zgorevanjem za cestna vozila for road vehicles in general
na splošno
53.060 Industrijski tovornjaki Industrial trucks
SIST EN 1175-2:1998/kFprA1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1175-2:1998/kFprA1:2010

---------------------- Page: 2 ----------------------

SIST EN 1175-2:1998/kFprA1:2010


EUROPEAN STANDARD
FINAL DRAFT
EN 1175-2:1998
NORME EUROPÉENNE

EUROPÄISCHE NORM
FprA1
March 2010
ICS 53.060
English Version
Safety of industrial trucks - Electrical requirements - Part 2:
General requirements of internal combustion engine powered
trucks
Sécurité des chariots de manutention - Prescriptions Sicherheit von Flurförderzeugen - Elektrische
électriques - Partie 2: Prescriptions générales des chariots Anforderungen - Teil 2: Allgemeine Anforderungen für
équipés d'un moteur thermique Flurförderzeuge mit Verbrennungsmotoren
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 150.

This draft amendment A1, if approved, will modify the European Standard EN 1175-2:1998. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.



Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1175-2:1998/FprA1:2010: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1175-2:1998/kFprA1:2010
EN 1175-2:1998/FprA1:2010 (E)
Contents
Page
Foreword . 3
1 Modifications to the Foreword . 4
2 Modifications to the Introduction . 5
3 Modifications to Clause 1 ( Scope ) . 5
4 Modification to Clause 2 ( Normative references ) . 5
5 Modifications to Clause 4 ( List of hazards ) . 5
6 Modification to 5.3.3 ( Load handling control ) . 6
7 Modification to 5.3.4 ( Speed limitation ) . 6
8 Modification to 5.3.5 ( Steering control ). 6
9 Addition of 5.3.6 ( Parameter ) . 6
10 Addition of 5.6 ( Electromagnetic radiations ) . 7
11 Addition of 6.3 ( Non ionising radiation ) . 7
12 Modification to Annex ZA . 7
13 Addition of Annex ZB. 7
2

---------------------- Page: 4 ----------------------

SIST EN 1175-2:1998/kFprA1:2010
EN 1175-2:1998/FprA1:2010 (E)
Foreword
This document (EN 1175-2:1998/FprA1:2010) has been prepared by Technical Committee
CEN/TC 150 “Industrial trucks - Safety”, the secretariat of which is held by BSI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive, see informative Annexes ZA and ZB, which are integral parts of this
document.

3

---------------------- Page: 5 ----------------------

SIST EN 1175-2:1998/kFprA1:2010
EN 1175-2:1998/FprA1:2010 (E)
1 Modifications to the Foreword
nd
Add after the 2 paragraph:
"This document has been prepared under a mandate given to CEN by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of
this document.".
rd
Add after the 3 paragraph:
"The main changes compared to the previous version are:
 addition of Annex ZB;
 editorial modification of Annex ZA;
 , minor technical changes in 5.3;
 requirements for radiation and software parameters;
 reference to EN 292-1 be replaced with EN ISO 12100-1:2003, EN 292-2 be replaced with
EN ISO 12100-2:2003 and EN 954-1 be replaced with EN ISO 13849-1.".
st
Delete the whole 3 paragraph.
st
Replace in the 4 paragraph
"prEN 1726 Safety of machinery - Industrial trucks - Self propelled trucks up to and including 10 000
kg capacity and tractors with a drawbar pull up to and including 20 000 N." with "prEN ISO 3696-1,
Industrial trucks - Safety requirements and verification - Part 1: Self-propelled industrial trucks, other
than driverless variable-reach trucks and burden-carrier trucks (ISO/DIS 3691-1:2008)",
"prEN 1726-2" with "EN 1726-2",
"prEN 1551" with "EN 1551",
"prEN 1459" with "EN 1459" and replace "Variable" with "Self propelled variable",
"prEN 1757-1, Safety of industrial trucks - Pedestrial controlled manual and semi manual trucks - Part
1: Stacker trucks" with "EN ISO 3691-5, Industrial trucks - Safety requirements and verification - Part
5: Pedestrian-propelled trucks (ISO 3691-5:2009)" and delete the references to
...