43.060 - Internal combustion engines for road vehicles

This document specifies tests and requirements for the manual cylinder valve, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with ISO 15403-1. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers;...view more

This document specifies tests and requirements for the manual valve, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with ISO 15403-1. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; c) stati...view more

This document specifies the dimensions required for the installation and integration of the fuel injectors in gasoline (GDI) engines. It also describes the interface of the fuel injector cup within the fuel rail to the individual injector. NOTE When the word "fuel" is used in the terms listed, it can be omitted, provided there is no misunderstanding.

This document specifies tests and requirements for the excess flow valve, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with the ISO 15403 series. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel contai...view more

This document establishes and specifies uniform test procedures, conditions, equipment and a performance report to permit the direct laboratory performance comparison of air cleaners. The basic performance characteristics of greatest interest are air flow restriction or differential pressure, dust collection efficiency, dust capacity and oil carry-over on oil bath air cleaners. This test code therefore deals with the measurement of these parameters. This document is applicable to air cleaners us...view more

This document specifies tests and requirements for the filter, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with the ISO 15403 series. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; c) st...view more

This document specifies tests and requirements for the automatic valve, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with the ISO 15403 series. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containe...view more

This document specifies tests and requirements for the pressure regulator, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with the ISO 15403 series It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel contai...view more

This document specifies tests and requirements for the check valve, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with the ISO 15403 series. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; ...view more

This document specifies tests and requirements for fittings, compressed natural gas (CNG) fuel system components intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with the ISO 15403 series. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; c) stati...view more

This document specifies tests and requirements for the rigid fuel line in stainless steel, a compressed natural gas (CNG) fuel system component in accordance with ISO 1127 intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with the ISO 15403 series. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of,...view more

This document specifies a method for testing engines designed for automotive vehicles. It applies to the evaluation of their performance with a view, in particular to presenting curves of power and specific fuel consumption at full load as a function of engine speed. It applies only to net power assessment. This document concerns internal combustion engines used for propulsion of passenger cars, trucks and other motor vehicles, excluding motorcycles, mopeds and agricultural tractors normally tra...view more

This document defines particle size distribution by number and chemical content limits involving one grade of test aerosol made from combustion soot.

This document specifies the principal dimensional characteristics of V-ribbed pulley groove profiles, together with the corresponding endless V-ribbed belts of PK profile which are used predominantly for automotive accessory drive applications. This document does not apply to the complete array of V-ribbed belts and pulleys of PH, PJ, PK, PL and PM profile for industrial and other non-automotive applications which are covered by ISO 9982. PK belt profile dimensions and tolerances are the same in...view more

This document specifies the requirements for belts and pulleys for V-belt drives used for driving auxiliaries of internal combustion engines for the automotive industry.

This document specifies measurement methods for the drive monitoring system that is
specified in IEC TS 63033-1:2017.

This document specifies cleanliness assessment procedures for evaluating the amount of debris present on the clean side of the constituent parts of high-pressure gasoline direct fuel injection systems. The presence of such debris could lead to a reduction in the system's operational performance. While other International Standards (e.g. ISO 16232) relate to the cleanliness of different types of components used in road vehicle fluid circuits, this document focuses on the special procedures applie...view more

This document specifies a method for testing internal combustion engines for propulsion of road vehicles as defined in ISO 3833. It applies to the evaluation of their performance with a view, in particular, to presenting curves of power and specific fuel consumption at full load as a function of engine speed. This document is applicable to gross power assessment. This document concerns internal combustion engines used for propulsion of passenger cars, trucks and other motor vehicles, excluding m...view more

This document defines the measuring principles used for measuring piston pins; it applies to piston pins with a nominal outer diameter from 8 mm up to and including 100 mm, for reciprocating internal combustion engines for road vehicles and other applications. In certain applications, except road vehicles, and provided that mutual agreement is made between the purchaser and the manufacturer, this document can be used with suitable modifications.

This document defines the minimum design, installation, commissioning, operation, inspection and maintenance requirements, for the safety, and, where appropriate, for the performance of public and non-public fuelling stations that dispense gaseous hydrogen to light duty road vehicles (e.g. fuel cell electric vehicles). This document is not applicable to the dispensing of cryogenic hydrogen, or hydrogen to metal hydride applications. Since this document is intended to provide minimum requirements...view more