SIST EN IEC 63033-3:2020
(Main)Car multimedia systems and equipment - Drive monitoring system - Part 3: Measurement methods (IEC 63033-3:2019)
Car multimedia systems and equipment - Drive monitoring system - Part 3: Measurement methods (IEC 63033-3:2019)
This document specifies measurement methods for the drive monitoring system that is
specified in IEC TS 63033-1:2017.
Multimediasysteme und -geräte in Fahrzeugen - Fahrüberwachungssystem - Teil 3: Messverfahren (IEC 63033-3:2019)
Systèmes et équipements multimédias pour automobiles - Système de surveillance de la conduite Partie 3: Méthodes de mesure (IEC 63033-3:2019)
L'IEC 63033-3:2019 spécifie les méthodes de mesure pour le système de surveillance de la conduite spécifié dans l’IEC TS 63033-1:2017.
Avtomobilski multimedijski sistemi in oprema - Sistem za nadzor vožnje - 3. del: Merilne metode (IEC 63033-3:2019)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 63033-3:2020
01-julij-2020
Avtomobilski multimedijski sistemi in oprema - Sistem za nadzor vožnje - 3. del:
Merilne metode (IEC 63033-3:2019)
Car multimedia systems and equipment - Drive monitoring system - Part 3:
Measurement methods (IEC 63033-3:2019)
Multimediasysteme und -geräte in Fahrzeugen - Fahrüberwachungssystem - Teil 3:
Messverfahren (IEC 63033-3:2019)
Systèmes et équipements multimédias pour automobiles - Système de surveillance de la
conduite Partie 3: Méthodes de mesure (IEC 63033-3:2019)
Ta slovenski standard je istoveten z: EN IEC 63033-3:2019
ICS:
33.160.60 Večpredstavni (multimedijski) Multimedia systems and
sistemi in oprema za teleconferencing equipment
telekonference
43.060.50 Električna in elektronska Electrical and electronic
oprema. Krmilni sistemi equipment. Control systems
SIST EN IEC 63033-3:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 63033-3:2020
---------------------- Page: 2 ----------------------
SIST EN IEC 63033-3:2020
EUROPEAN STANDARD EN IEC 63033-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2019
ICS 33.160.60; 43.040.10; 43.040.15
English Version
Car multimedia systems and equipment - Drive monitoring
system - Part 3: Measurement methods
(IEC 63033-3:2019)
Systèmes et équipements multimédias pour automobiles - Multimediasysteme und -geräte in Fahrzeugen -
Système de surveillance de la conduite Partie 3: Méthodes Fahrüberwachungssystem - Teil 3: Messverfahren
de mesure (IEC 63033-3:2019)
(IEC 63033-3:2019)
This European Standard was approved by CENELEC on 2019-10-18. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63033-3:2019 E
---------------------- Page: 3 ----------------------
SIST EN IEC 63033-3:2020
EN IEC 63033-3:2019 (E)
European foreword
The text of document 100/3147/CDV, future edition 1 of IEC 63033-3, prepared by IEC/TC 100 "Audio,
video and multimedia systems and equipment" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 63033-3:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-07-18
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-10-18
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 63033-3:2019 was approved by CENELEC as a European
Standard without any modification.
2
---------------------- Page: 4 ----------------------
SIST EN IEC 63033-3:2020
EN IEC 63033-3:2019 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
ISO 16505 2019 Road vehicles - Ergonomic and performance - -
aspects of Camera Monitor Systems -
Requirements and test procedures
IEC/TS 63033-1 2017 Car multimedia systems and equipment - Drive - -
monitoring system - Part 1: General
UN Regulation No. Uniform provisions concerning the approval of - -
46 devices for indirect vision and of motor
vehicles with regards to the installation of
these devices
UN Regulation No. Uniform provisions concerning the approval of - -
125 motor vehicles with regards to the forward field
of vision of the motor vehicle driver
3
---------------------- Page: 5 ----------------------
SIST EN IEC 63033-3:2020
---------------------- Page: 6 ----------------------
SIST EN IEC 63033-3:2020
IEC 63033-3
®
Edition 1.0 2019-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Car multimedia systems and equipment – Drive monitoring system
Part 3: Measurement methods
Systèmes et équipements multimédias pour automobiles – Système de
surveillance de la conduite
Partie 3: Méthodes de mesure
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.160.60; 43.040.10; 43.040.15 ISBN 978-2-8322-7312-8
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 63033-3:2020
– 2 – IEC 63033-3:2019 © IEC 2019
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviated terms . 6
3.1 Terms and definitions . 6
3.2 Abbreviated terms . 6
4 System model . 6
5 Camera image quality . 7
5.1 Camera resolution. 7
5.2 Camera image quality . 7
6 Camera calibration . 7
6.1 General . 7
6.2 Verification. 7
7 Field of view . 9
8 Time behaviour . 9
8.1 Start-up time . 9
8.2 Frame rate . 9
8.3 Latency . 9
Annex A (informative) Field of view (FOV) . 10
Bibliography . 16
Figure 1 – System model of drive monitoring system . 7
Figure 2 – Orthogonal reference . 8
Figure 3 – Reference guideline . 8
Figure A.1 – Example view for Class I FOV . 10
Figure A.2 – Example view for Class II FOV . 11
Figure A.3 – Example view for Class III FOV . 12
Figure A.4 – Example view for Class IV FOV . 12
Figure A.5 – Example view for Class V FOV . 13
Figure A.6 – Example view for Larger FOV on the passenger side . 13
Figure A.7 – Example view for Class VI FOV . 14
Figure A.8 – Example view for FOV of 5.4.1 defined in UN Regulation No. 125 . 15
---------------------- Page: 8 ----------------------
SIST EN IEC 63033-3:2020
IEC 63033-3:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CAR MULTIMEDIA SYSTEMS AND EQUIPMENT –
DRIVE MONITORING SYSTEM
Part 3: Measurement methods
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The
...
SLOVENSKI STANDARD
oSIST prEN IEC 63033-3:2018
01-december-2018
Avtomobilski multimedijski sistemi in oprema - Sistem za nadzor vožnje - 3. del:
Merilne metode (TA 17)
Car multimedia systems and equipment - Drive monitor system Part 3 : Measurement
methods (TA 17)
Ta slovenski standard je istoveten z: prEN IEC 63033-3:2018
ICS:
33.160.60 9HþSUHGVWDYQL PXOWLPHGLMVNL Multimedia systems and
VLVWHPLLQRSUHPD]D teleconferencing equipment
WHOHNRQIHUHQFH
43.060.50 (OHNWULþQDLQHOHNWURQVND Electrical and electronic
RSUHPD.UPLOQLVLVWHPL equipment. Control systems
oSIST prEN IEC 63033-3:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN IEC 63033-3:2018
---------------------- Page: 2 ----------------------
oSIST prEN IEC 63033-3:2018
100/3147/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 63033-3 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2018-10-26 2019-01-18
SUPERSEDES DOCUMENTS:
100/3030/CD,100/3104/CC
IEC TA 17 : MULTIMEDIA SYSTEMS AND EQUIPMENT FOR CARS
SECRETARIAT: SECRETARY:
Korea, Republic of Mr Ock-Woo Nam
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
TITLE:
Car multimedia systems and equipment - Drive monitoring system - Part 3 : Measurement
methods (TA 17)
PROPOSED STABILITY DATE: 2022
NOTE FROM TC/SC OFFICERS:
Copyright © 2018 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
---------------------- Page: 3 ----------------------
oSIST prEN IEC 63033-3:2018
100/3147/CDV - 2 - IEC 63033-3/CDV © IEC 2018
CONTENTS
FOREWORD . 2
INTRODUCTION . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviated terms . 5
3.1 Terms and definitions . 5
3.2 Abbreviated terms . 5
4 System model . 5
4.1 General . 5
5 Camera image quality . 6
5.1 Camera resolution. 6
5.2 Camera image quality . 6
6 Camera calibration . 6
6.1 General . 6
6.2 Verification. 6
7 Field of view . 8
8 Time behaviour . 8
8.1 Start-up time . 8
8.2 Frame rate . 8
8.3 Latency . 9
Annex A (informative) Field of view (FOV) . 10
A.1 General . 10
A.2 Example view for Class I FOV . 10
A.3 Example view for Class II FOV . 11
A.4 Example view for Class III FOV . 12
A.5 Example view for Class IV FOV . 12
A.6 Example view for Class V FOV . 13
A.7 Example view for Larger FOV on the passenger side . 13
A.8 Example view for Class VI FOV . 14
A.9 Example view for FOV of 5.4.1 defined in UN REGULATION No. 125 . 14
Bibliography . 16
Figure 1 – System model of drive monitoring system . 6
Figure 2 – Orthogonal Reference . 7
Figure 3 – Reference Guideline . 8
Figure A.1 – Example view for Class I FOV . 10
Figure A.2 – Example view for Class II FOV . 11
Figure A.3 – Example view for Class III FOV . 12
Figure A.4 – Example view for Class IV FOV . 12
Figure A.5 – Example view for Class V FOV . 13
Figure A.6 – Example view for Larger FOV on the passenger side . 13
Figure A.7 – Example view for Class VI FOV . 14
Figure A.8 – Example view for FOV of 5.4.1 defined in UN REGULATION No. 125 . 15
---------------------- Page: 4 ----------------------
oSIST prEN IEC 63033-3:2018
---------------------- Page: 5 ----------------------
oSIST prEN IEC 63033-3:2018
100/3147/CDV - 2 - IEC 63033-3/CDV © IEC 2018
1 INTERNATIONAL ELECTROTECHNICAL COMMISSION
2 ____________
3
4 CAR MULTIMEDIA SYSTEMS AND EQUIPMENT –
5 DRIVE MONITORING SYSTEM
6
7 Part 3: Measurement methods
8
9 FOREWORD
10 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
11 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
12 international co-operation on all questions concerning standardization in the electrical and electronic fields. To
13 this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
14 Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
15 Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
16 in the subject dealt with may participate in this preparatory work. International, governmental and non-
17 governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
18 with the International Organization for Standardization (ISO) in accordance with conditions determined by
19 agreement between the two organizations.
20 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
21 consensus of opinion on the relevant subjects since each technical committee has representation from all
22 interested IEC National Committees.
23 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
24 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
25 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
26 misinterpretation by any end user.
27 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
28 transparently to the maximum extent possible in their national and regional publications. Any divergence
29 between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
30 the latter.
31 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
32 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
33 services carried out by independent certification bodies.
34 6) All users should ensure that they have the latest edition of this publication.
35 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
36 members of its technical committees and IEC National Committees for any personal injury, property damage or
37 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
38 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
39 Publications.
4
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.