SIST EN 13112:2003/kFprA1:2009
(Amendment)Tannery machines - Splitting and bandknife shearing machines - Safety requirements
Tannery machines - Splitting and bandknife shearing machines - Safety requirements
Type 1 amendment.
Gerberei-Maschinen - Spalt- und Bandmesserschermaschinen - Sicherheitsanforderungen
Machines de tannerie - Machines à refendre et tondeuses à ruban - Prescriptions de sécurité
Strojarski stroji - Stroji za cepljenje in tračno striženje - Varnostne zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13112:2003/kFprA1:2009
01-junij-2009
6WURMDUVNLVWURML6WURML]DFHSOMHQMHLQWUDþQRVWULåHQMH9DUQRVWQH]DKWHYH
Tannery machines - Splitting and bandknife shearing machines - Safety requirements
Gerberei-Maschinen - Spalt- und Bandmesserschermaschinen -
Sicherheitsanforderungen
Machines de tannerie - Machines à refendre et tondeuses à ruban - Prescriptions de
sécurité
Ta slovenski standard je istoveten z: EN 13112:2002/FprA1
ICS:
59.140.40 Stroji in oprema za Machines and equipment for
proizvodnjo usnja in krzna leather and fur production
SIST EN 13112:2003/kFprA1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13112:2003/kFprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 13112:2003/kFprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 13112:2002
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
April 2009
ICS 59.140.40
English Version
Tannery machines - Splitting and bandknife shearing machines -
Safety requirements
Machines de tannerie - Machines à refendre et tondeuses à Gerberei-Maschinen - Spalt- und
ruban - Prescriptions de sécurité Bandmesserschermaschinen - Sicherheitsanforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 200.
This draft amendment A1, if approved, will modify the European Standard EN 13112:2002. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13112:2002/FprA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13112:2003/kFprA1:2009
EN 13112:2002/FprA1:2009 (E)
Foreword
This document (EN 13112:2002/FprA1:2009) has been prepared by Technical Committee CEN/TC 200
“Tannery machinery - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
The first reason for amending the published standard EN 13112:2002 is the revision of the EU-Machinery
Directive 98/37/EC into 2006/42/EC, requiring the adaptation of published European Standards cited in the
Official Journal of the European Communities under that Directive.
Additionally at this occasion the normative references have been updated, while also some other limited rather
editorial improvements and corrections have been made.
2
---------------------- Page: 4 ----------------------
SIST EN 13112:2003/kFprA1:2009
EN 13112:2002/FprA1:2009 (E)
1 Modification to the Foreword
th
Replace the existing 4 paragraph with the following: "For relationship with EU Directive(s), see informative
Annexes ZA and ZB, which are integral parts of this document.".
2 Modification to the Introduction
Replace the complete text with the following:
"This document is a type C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and hazardous events are
covered are indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.".
3 Modification to Clause 1, Scope
th
Replace the 4 paragraph “This European Standard applies to the machines manufactured after its date of
issue.” with the following: "This document is not applicable to the splitting and bandknife shearing machines
which are manufactured before the date of its publication as EN.".
4 Modification to Clause 2, Normative references
Introductory text: Replace the first paragraph with the following: "The following referenced documents are
indispensable for the application of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.".
Delete all full stops at the end of reference titles.
EN 292-1: Delete this item and add the following: "EN ISO 12100-1:2003, Safety of machinery — Basic
concepts, general principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003)".
EN 292-2: Delete this item and add the following: "EN ISO 12100-2:2003, Safety of machinery — Basic
concepts, general principles for design — Part 2: Technical principles (ISO 12100-2:2003)".
EN 418: Delete this item and add the following: "EN ISO 13850:2006, Safety of machinery — Emergency stop
— Principles for design (ISO 13850:2006)".
EN 457: Delete this item and add the following: “EN ISO 7731:2008, Ergonomics — Danger signals for public
and work areas — Auditory danger signals (ISO 7731:2003)”.
EN 954-1: Delete this item and add the following: "EN ISO 13849-1:2008, Safety of machinery — Safety-
related parts of control systems — Part 1: General principles for design (ISO 13849-1:2006)".
Delete reference to EN 1070.
3
---------------------- Page: 5 ----------------------
SIST EN 13112:2003/kFprA1:2009
EN 13112:2002/FprA1:2009 (E)
prEN 1760-2: Replace this item with the following: "EN 1760-2:2001, Safety of machinery — Pressure
sensitive protective devices — Part 2: General principles for the design and testing of pressure sensitive
edges and pressure sensitive bars”.
EN ISO 3743-1: Replace "EN ISO 3743-1" with "EN ISO 3743-1:1995”.
EN ISO 3743-2: Replace "EN ISO 3743-2" with "EN ISO 3743-2:1996”.
EN ISO 3744: Replace "EN ISO 3744" with "EN ISO 3744:1995”.
EN ISO 3746: Replace "EN ISO 3746" with "EN ISO 3746:1995”.
EN ISO 3747: Replace "EN ISO 3747" with "EN ISO 3747:2000”.
EN ISO 4871: Replace "EN ISO 4871" with "EN ISO 4871:1996”.
Replace the reference EN ISO 9614 with the following:
“EN ISO 9614-1:1995, Acoustics — Determination of sound power levels of noise sources using sound
intensity — Part 1: Measurements at discrete points (ISO 9614-1:1993)
EN ISO 9614-2:1996, Acoustics — Determination of sound power levels of noise sources using sound
intensity — Part 2: Measurement by scanning (ISO 9614-2:1996)
EN ISO 9614-3:2002, Acoustics — Determination of sound power levels of noise sources using sound
intensity — Part 3: Precision method for measurement by scanning (ISO 9614-3:2002)”.
EN ISO 11201: Replace "EN ISO 11201" with "EN ISO 11201:1995”.
EN ISO 11202: Replace "EN ISO 11202" with "EN ISO 11202:1995”.
EN ISO 11203: Replace "EN ISO 11203" with "EN ISO 11203:1995”.
EN ISO 11204: Replace "EN ISO 11204" with "EN ISO 11204:1995”.
EN ISO 11688-1: Replace "EN ISO 11688-1" with "EN ISO 11688-1:1998".
EN ISO 11688-2: Replace "EN ISO 11688-2" with "EN ISO 11688-2:2000".
EN 61496-1:1997: Replace this item with the following: "EN 61496-1:2004, Safety of machinery — Electro-
sensitive protective equipment — Part 1: General requirements and tests (IEC 61496-1:2004, modified)".
prEN 61496-2:1997: Replace this item with the following: "CLC/TS 61496-2:2006, Safety of machinery —
Electro-sensitive protective equipment — Particular requirements for equipment using active optoelectronic
protective devices (AOPDs) (IEC 61496-2:2006)".
EN 60204-1:1997: Replace this item with: "EN 60204-1:2006, Safety of machinery — Electrical equipment of
machines — Part 1: General requirements (IEC 60204-1:2005, modified)".
5 Modification to Clause 3, Terms and definitions - Terminology
Introductory paragraph: replace the text with the following: "For the purposes of this document, the terms and
definitions given in EN ISO 12100-1:2003 and the following apply.".
4
---------------------- Page: 6 ----------------------
SIST EN 13112:2003/kFprA1:2009
EN 13112:2002/FprA1:2009 (E)
6 Modification to Clause 4, List of hazards
Replace the heading of this clause with: "List of significant hazards" and add the following table title: "Table 1 -
List of significant hazards".
Introductory paragraphs: replace the text with the following:
"This clause contains all the significant hazards, hazardous situations and events, as far as they are dealt with
in this document, identified by risk assessment as significant for this type of machinery and which require
action to eliminate or reduce the risk.
The significant hazards for splitting and bandknife shearing machines are outlined in 4.1 to 4.7.
The danger zones which give rise to mechanical hazards are illustrated in Figures 1, 2, 3, 4 and 5. The figures
are informative only.".
7 Modification to Clause 5, Safety requirements and/or measures
Delete the NOTE and the introductory text (hanging paragraphs).
5.1:
Replace the text with the following:
"Machinery shall comply with the safety requirements and/or protective measures of this clause.
In addition, the machine shall be designed according to the principles of EN ISO 12100-2 for relevant but not
significant hazards which are not dealt with by this document.
For hazards which are to be reduced by the application of a type B-standard such as EN 294, EN 953,
EN ISO 13850, EN 60204-1 etc., the manufacturer shall carry out a risk assessment to establish the
requirements of the B-standards which are to be applied.".
5.2.1.1:
st
Replace the following text in the 1 indent "EN 953 and 4.2.2.2 of EN 292-2:1991/A1:1995" with:
"EN 953 and 5.3.2.2 of EN ISO 12100-2:2003".
nd
Replace the following text in the 2 indent "EN 953, EN 1088 and 4.2.2.3 of EN 292-2:1991/A1:1995" with:
"EN 953, EN 1088 and 5.3.2.3 of EN ISO 12100-2:2003".
5.2.1.2:
st
Replace the following text in the 1 indent "EN 953 and 4.2.2.2 of EN 292-2:1991/A1:1995" with: "EN 953 and
5.3.2.2 of EN ISO 12100-2:2003".
nd
Replace the following text in the 2 indent "EN 953:1997, 4.2.2.1 of EN 292-2:1991/A1:1995" with: "EN 953
and 5.3.2.3 of EN ISO 12100-2:2003".
Add a second paragraph as follows: "Fixing systems of fixed guards and fixed covers shall remain attached to
these parts or to the machine when the parts are removed.".
5
---------------------- Page: 7 ----------------------
SIST EN 13112:2003/kFprA1:2009
EN 13112:2002/FprA1:2009 (E)
5.2.1.4:
st
Replace "will effect a shutdown of the" in the 1 paragraph with "will shutdown the" and "before reaching" with
"before".
nd
Replace the text in the 2 paragraph with the following:
“Suitable protective devices are:
- movable interlocking guards which satisfy EN 953 and EN 1088, 5.3.2.3 of EN ISO 12100-2:2003 and the
distances given in the appropriate table (1 or 3) of EN 294;
- trip devices, such as:
- electrosensitive protective devices satisfying EN 61496-1, CLC/TS 61496-2 and EN 999;
- pressure sensitive protective device satisfying EN 1760-2 type 3.1 or 3.2.”.
5.2.2.1:
Replace "EN 60529:1991" with: "EN 60529.
5.2.3:
Replace "see 7.1.2 j of this standard" with: "see 7.3.2 j)".
5.2.4:
rd
Replace the following text in the 3 paragraph "satisfy 3.8 of EN 292-2:1991/A1:1995, EN 982 and EN 983"
with: "satisfy 4.10 of EN 12100-2:2003, EN 982 and EN 983".
5.2.5:
Replace the text “in annex A and 7.1.2.h of this standard” with: “in Annex A and 7.3.2 h)”.
5.2.6.2:
Replace “see 7.1.1” with: “see 7.3.1”.
5.2.7.3:
st
Replace "same level as the" in the 1 indent with: "same performance level as for the".
nd
Replace the text in the 2 indent with:
"shall as a minimum comply with performance level “c” as defined in EN ISO 13849-1.".
5.2.8.1:
st st
Replace in the 1 sentence of the 1 paragraph "EN 418" with: "EN ISO 13850".
6
---------------------- Page: 8 ----------------------
SIST EN 13112:2003/kFprA1:2009
EN 13112:2002/FprA1:2009 (E)
5.3.1.2:
st
Replace the following text in the 1 indent "according to prEN 1760-2:1996 with a control system conforming
to the requirements of at least category 3 of EN 954-1 shall be applied" with: "according to EN 1760-2 and
with the related parts of the control system as a minimum complying with performance level “d” as defined in
EN ISO 13849-1".
nd
Replace the complete text in the 2 indent with
“an electrosensitive protective device of type 4 in accordance with EN 61496-1 and CLC/TS 61496-2 and with
the related parts of the control system as a minimum complying with performance level “d” as defined in
EN ISO 13849-1 and conforming to EN 999.".
Replace “EN 457” in the last but one paragraph with: “EN ISO 7731”.
5.3.1.3:
st
Replace “according to 3.7.9 and 1.2.5 of annex A of EN 292-2:1991/A1:1995” in the 1 paragraph with:
“according to 4.11.10 of EN ISO 12100-2:2003”.
5.3.1.4:
st
Replace the complete text in the 1 indent with:
“an electrosensitive protective device of type 4 in accordance with EN 61496-1 and CLC/TS 61496-2 and with
the related parts of the control system as a minimum complying with performance level “d” as defined in
EN ISO 13849-1 and conforming to EN 999.".
5.3.2.1.1:
Replace the text in the indents with the following:
“a fixed distance guard, according to EN 953, to 5.3.2.1 of EN ISO 12100-2:2003 and respecting the distances
of Table 4 of EN 294:1992, and
- a pressure sensitive protective device of type 3.1 or 3.2 according to EN 1760-2 and with the related parts of
the control system as a minimum complying with performance level “d” as defined in EN ISO 13849-1.”.
5.3.2.1.2:
Replace the text in the indent with the following:
“fixed enclosing guard in accordance with EN 953 and 5.3.2.2 of EN ISO 12100
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.