SIST EN 1715-1:2008

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium and aluminium alloys - Drawing stock - Part 1: General requirements and technical conditions for inspection and deliveryAluminium et alliages d'aluminium - Fil machine - Partie 1: Exigences générales et conditions techniques de contrôle et de livraisonAluminium und Aluminiumlegierungen - Vordraht - Teil 1: Allgemeine Anforderungen und Technische Lieferbedingungen77.150.10Aluminijski izdelkiAluminium productsICS:SIST EN 1715-1:2008en,fr,deTa slovenski standard je istoveten z:EN 1715-1:200801-julij-2008SIST EN 1715-1:2008SLOVENSKI
STANDARDSIST EN 1715-1:19981DGRPHãþD







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1715-1April 2008ICS 77.150.10Supersedes EN 1715-1:1997
English VersionAluminium and aluminium alloys - Drawing stock - Part 1:General requirements and technical conditions for inspectionand deliveryAluminium et alliages d'aluminium - Fil machine - Partie 1:Exigences générales et conditions techniques de contrôleet de livraisonAluminium und Aluminiumlegierungen - Vordraht - Teil 1:Allgemeine Anforderungen und TechnischeLieferbedingungenThis European Standard was approved by CEN on 14 March 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1715-1:2008: E



EN 1715-1:2008 (E) 2 Contents Page Foreword.3 1 Scope.5 2 Normative references.5 3 Terms and definitions.6 4 Ordering information.6 5 Requirements.7 5.1 Production and manufacturing processes.7 5.2 Quality control.8 5.3 Aluminium and aluminium alloys used.8 5.4 Technical specifications.8 6 Product inspection and test methods.11 6.1 Analysis of chemical composition.11 6.2 Thermal treatment control.11 6.3 Mechanical properties.11 6.4 Surface appearance.12 6.5 Other tests.12 7 Delivery documents and inspection documents.12 7.1 Certificate of mass and analysis.12 7.2 Inspection certificate.12 8 Marking.12 9 Packaging, transport and storage.13 9.1 Packaging.13 9.2 Transport and storage.13 10 Complaints of non conformity.13 Annex A (normative)
Rules for rounding.14



EN 1715-1:2008 (E) 3 Foreword This document (EN 1715-1:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by October 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1715-1:1997. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 4 "Wires and drawing stock" to revise EN 1715-1:1997. Besides editorial adjustments in the text and update of normative references, the following changes have been made:  Scope: maximum unit mass increased from 3 t to 4 t. Addition of metal spraying and food packaging applications. Addition of hot extruded rod (HER).  Clause 2: addition of EN 12258-1, EN 14242, EN 14726, EN ISO 18273  Clause 4: amended  Clause 5: amended  Table 1: deleted  Table 2: becomes Table 1  Clause 6: amended  Clause 7: in 7.2 deletion of 7.2.1 to 7.2.2.3  Clause 10: title amended EN 1715 comprises the following parts under the general title "Aluminium and aluminium alloys – Drawing stock":  Part 1: General requirements and technical conditions for inspection and delivery  Part 2: Specific requirements for electrical applications  Part 3: Specific requirements for mechanical uses (excluding welding)  Part 4: Specific requirements for welding applications



EN 1715-1:2008 (E) 4  Part 5: Specific requirements for aluminium food packaging1) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms that it is its policy that in the case when a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory conditions, then this product is removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
1) Under preparation.



EN 1715-1:2008 (E) 5 1 Scope This European Standard specifies general requirements for drawing stock of aluminium and aluminium alloys delivered in the form of coils with a unit mass ranging between 1 t and 4 t and obtained by common industrial processes. It also specifies the technical conditions for inspection and delivery of these products. It applies to drawing stock intended for the following main fields of application:  wires for general electrical purposes;  wires for general mechanical uses;  wires for brazing and welding and metal spraying;  food packaging. The specific requirements to drawing stock for these applications are specified in EN 1715-2, EN 1715-3 and EN 1715-4. It does not apply to wires which are drawn, but only to drawing stock which is produced by hot-working. NOTE Three main methods exist for the manufacture of drawing stock: a) continuously cast rod (CCR):  a section is cast continuously in the groove of a wheel, the groove being closed by an endless strip;  the solid and still hot section is rolled in a multistand rolling mill to the required diameter;  the drawing stock rod thus produced is wound continuously to form coils up to 4 t in mass; b) hot rolled rod (HRR):  a wirebar of diameter approximately 100 mm to 150 mm is heated and rolled to the required diameter;  the coils, weighing up to approximately 100 kg are butt welded together and wound to form coils with mass of 1 t to 4 t; c) hot extruded rod (HER):  coils up to 100 kg can be produced in a single fibre without butt welds (depending on the size of the extrusion press);  coils over 100 kg are normally produced by block on block extrusion, generating "Zweiwachs"-joints. For mechanical applications (i.e fasteners) the "Zweiwachs" area should be marked. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 515, Aluminium and aluminium alloys — Wrought products — Temper designations



EN 1715-1:2008 (E) 6 EN 573-3, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 3: Chemical composition and form of products EN 1715-2, Aluminium and aluminium alloys — Drawing stock — Part 2: Specific requirements for electrical applications EN 1715-3, Aluminium and aluminium alloys — Drawing stock — Part 3: Specific requirements for mechanical uses (excluding welding) EN 1715-4, Aluminium and aluminium alloys — Drawing stock – Part 4: Specific requirements for welding applications EN 10002-1, Metallic materials — Tensile testing — Part 1: Method of test at ambient temperature EN 10204, Metallic products — Types of inspection documents EN 12258-1:1998, Aluminium and aluminium alloys — Terms and definitions — Part 1: General terms EN 14242, Aluminium and aluminium alloys — Chemical analysis — Inductively coupled plasma optical emission spectral analysis EN 14726, Aluminium and aluminium alloys — Chemical analysis — Guideline for spark optical emission spectrometric analysis EN ISO 18273, Welding consumables — Wire electrodes, wires and rods for welding of aluminium and aluminium alloys — Classification (ISO 18273:2004) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 drawing stock intermediate wrought solid product manufactured by hot working with cross-section approximately circular along its entire length, delivered in coils and in a single length, and with a unit mass normally ranging between 1 t and 4 t 3.2 cast quantity of liquid metal in the furnace that has simultaneously undergone the same treatment before continuously casting and rolling or casting into wirebar or extrusion ingot 3.3 manufacturing batch quantity of final product produced from the same cast, during the same manufacturing run and treatment charge with the same temper and diameter 3.4 delivery batch quantity of final product produced from the same cast, temper, diameter, and forming part of the same shipment 4 Ordering information The order shall define the product in detail and shall contain the following information:



EN 1715-1:2008 (E) 7 a) the type of product:  product identification: drawing stock;  designation of the aluminium grade or aluminium alloy in accordance with EN 573-3;  unit mass of the coil; b) the dimensions expressed in millimetres:  nominal diameter of the drawing stock;  dimensions of coils; c) the temper of the product for delivery and, if different, the temper for use in accordance with EN 515; d) reference to the relevant parts of this European Standard; e) quantity:  mass (in metric tons);  tolerances on quantity (if required); f) any special requirement agreed between supplier and purchaser, for example:  properties other than those specified in EN 1715-2, EN 1715-3 or EN 1715-4;  loose or tight winding;  surface protection;  special packaging;  special marking;  any requirement for certificates of conformity, test and/or anal
...