SIST EN 1715-3:2008
(Main)Aluminium and aluminium alloys - Drawing stock - Part 3: Specific requirements for mechanical uses (excluding welding)
Aluminium and aluminium alloys - Drawing stock - Part 3: Specific requirements for mechanical uses (excluding welding)
This European Standard specifies specific requirements for drawing stock of aluminium and aluminium alloys for general mechanical uses (excluding welding).
The general requirements and technical conditions for inspection and delivery are specified in EN 1715-1.
This European Standard does not apply to drawn wire.
Aluminium und Aluminiumlegierungen - Vordraht - Teil 3: Besondere Anforderungen für mechanische Anwendungen (ausgenommen Schweißen)
Diese Europäische Norm legt die besonderen Anforderungen an Vordraht aus Aluminium und
Aluminiumlegierungen für mechanische Anwendungen (ausgenommen Schweißen) fest.
Die allgemeinen Anforderungen und Technischen Lieferbedingungen sind in EN 1715-1 festgelegt.
Diese Europäische Norm gilt nicht für gezogenen Draht.
Aluminium et alliages d'aluminium - Fil machine - Partie 3: Exigences spécifiques pour les applications mécaniques (soudage excepté)
La présente Norme européenne prescrit des exigences spécifiques applicables au fil machine en aluminium et
alliages d'aluminium pour les applications mécaniques (soudage excepté).
Les exigences générales et les conditions techniques de contrôle et de livraison sont spécifiées dans
l’EN 1715-1.
La présente Norme européenne ne s'applique pas au fil étiré.
Aluminij in aluminijeve zlitine - Vlečeni polizdelki - 3. del: Posebne zahteve za uporabo v strojne namene (razen varjenja)
General Information
- Status
- Published
- Publication Date
- 19-May-2008
- Technical Committee
- INEK - Nonferrous metals
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 07-May-2008
- Due Date
- 12-Jul-2008
- Completion Date
- 20-May-2008
Relations
- Effective Date
- 01-Jul-2008
- Effective Date
- 01-Jul-2008
Overview
EN 1715-3:2008 - Aluminium and aluminium alloys - Drawing stock - Part 3: Specific requirements for mechanical uses (excluding welding) specifies the requirements for aluminium drawing stock intended for general mechanical uses (excluding welding and excluding drawn wire). It defines alloy selection, delivery tempers, inspection and testing frequency, and the documentation required at delivery. General delivery conditions are covered in EN 1715-1.
Keywords: EN 1715-3:2008, aluminium drawing stock, mechanical uses, tempers, chemical composition, mechanical properties
Key topics and technical requirements
- Scope and exclusions
- Applies to drawing stock for mechanical uses; does not apply to drawn wire and excludes welding applications.
- Chemical composition
- Alloys and compositions must comply with EN 573-3.
- Certificates must report Si, Fe, Cu, Mn, Mg, Cr, Ni, Zn, Ti, Ga and V; any other elements specified in EN 573-3 (e.g., Pb, Bi, Zr) shall also be reported.
- Alloys and typical tensile ranges
- Table 1 in the standard lists main alloys used for mechanical purposes (examples: EN AW-6060, EN AW-6061, EN AW-6082, EN AW-7075, etc.) with typical tensile strength ranges and recommended delivery tempers.
- Foreword notes updates from the previous edition (e.g., alloy EN AW-6056 added).
- Tempers for delivery
- Tempers shall be designated per EN 515. Usual tempers include F (as fabricated), O (annealed), O3 (homogenised), T4 (solution treated, naturally aged).
- If no temper is specified by the purchaser, the default delivered temper is F.
- Inspection and testing
- Chemical composition: checked for each cast as per EN 1715-1.
- Mechanical properties: measured at least once per coil; alternate sampling frequencies may be agreed between manufacturer and purchaser.
- Delivery documentation
- Requires a certificate of mass and analysis and a test report (identifying alloy, temper, diameter, coil IDs, mechanical test results, dates, net mass) as specified in EN 1715-1.
- Marking and packaging
- Per EN 1715-1.
Applications
- Use for procurement, manufacture and quality control of aluminium drawing stock intended for mechanical forming and fabrication (excluding welding). The standard is relevant where defined alloy chemistry, temper and tensile properties affect downstream processing and final part performance.
Who should use this standard
- Aluminium drawing-stock manufacturers, quality and production engineers, procurement specialists, testing laboratories, and designers specifying material for mechanical applications.
Related standards
- EN 1715-1 (General requirements and inspection/delivery)
- EN 515 (Temper designations)
- EN 573-3 (Chemical composition of wrought products)
- Other EN 1715 parts (Part 2 electrical, Part 4 welding, Part 5 food packaging)
Frequently Asked Questions
SIST EN 1715-3:2008 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Aluminium and aluminium alloys - Drawing stock - Part 3: Specific requirements for mechanical uses (excluding welding)". This standard covers: This European Standard specifies specific requirements for drawing stock of aluminium and aluminium alloys for general mechanical uses (excluding welding). The general requirements and technical conditions for inspection and delivery are specified in EN 1715-1. This European Standard does not apply to drawn wire.
This European Standard specifies specific requirements for drawing stock of aluminium and aluminium alloys for general mechanical uses (excluding welding). The general requirements and technical conditions for inspection and delivery are specified in EN 1715-1. This European Standard does not apply to drawn wire.
SIST EN 1715-3:2008 is classified under the following ICS (International Classification for Standards) categories: 77.150.10 - Aluminium products. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 1715-3:2008 has the following relationships with other standards: It is inter standard links to SIST EN 1715-3:2002/AC:2002, SIST EN 1715-3:2002. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 1715-3:2008 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium and aluminium alloys - Drawing stock - Part 3: Specific requirements for mechanical uses (excluding welding)Aluminium et alliages d'aluminium - Fil machine - Partie 3: Exigences spécifiques pour les applications mécaniques (soudage excepté)Aluminium und Aluminiumlegierungen - Vordraht - Teil 3: Besondere Anforderungen für mechanische Anwendungen (ausgenommen Schweißen)77.150.10Aluminijski izdelkiAluminium productsICS:SIST EN 1715-3:2008en,fr,deTa slovenski standard je istoveten z:EN 1715-3:200801-julij-2008SIST EN 1715-3:2008SLOVENSKI
STANDARDSIST EN 1715-3:2002/AC:2002SIST EN 1715-3:20021DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1715-3April 2008ICS 77.150.10Supersedes EN 1715-3:1997
English VersionAluminium and aluminium alloys - Drawing stock - Part 3:Specific requirements for mechanical uses (excluding welding)Aluminium et alliages d'aluminium - Fil machine - Partie 3:Exigences spécifiques relatives aux applicationsmécaniques (soudage excepté)Aluminium und Aluminiumlegierungen - Vordraht - Teil 3:Besondere Anforderungen für mechanische Anwendungen(ausgenommen Schweißen)This European Standard was approved by CEN on 14 March 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1715-3:2008: E
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...